Rugged Mobile Terminal
User Guide
Accessories
Main Device
1Set
Power Adapter
1Piece
Battery
1Piece
User Guide
1Volume
Before using the device，ensure that all the accessories
above are included in the package.
If you have any problems，please contact the services
provider of the distributors.
Screwdriver
1Volume
2
NFC Card Reading
1. Put the NFC card above the NFC board and hold.
7
1 3 4
Battery Installation
1. Put the battery into the holder and install the battery cover as figure.
Then lock the battery cover with four screws.
1. This device uses a custom battery. Please not replace other
types of batteries.
CAUTION: Attempting to replace the incorrect battery can
cause an explosion from the battery.
2. Do not put the battery into the fire or a hot oven, or undergo
mechanical shock or crush, there is a danger of explosion.
3. If the battery is not used for a long time (>6 months), please
charge it to 50%~70%, then remove it from the device, and
store it in the environment of 10°C~35°C, 45%RH~85%RH.
It is recommended that the battery should be recharged every
3 months to avoid damaging.
4. If the device is not used for more than 2 weeks, please unplug
Warning
the battery to prevent overcharge.
Product Description
封面
封底
材质为105铜版纸，页面1和页面2，双面印刷，成品尺寸为90*150mm，风琴折
①
②
③
Front Camera
Volume Button
Power Button
Function Button
NFC
Type-C Port
Bracket Mounting Hole Reset Key
Rear Camera
2. Push the SIM card into the socket correctly. Be sure the SIM
card is in right position.
SAM Card Slot
Micro SD Card Slot
Micro SIM Card Slot
SIM Card, SAM Card & TF Card Installation
1. Remove the four screws and remove the battery cover as
figure. Take out the battery and remove the sticker.
① ②
③
④
USB Cable
1Piece
Bracket
1piece
Wristband
1Piece
6
Option B
5
There are two options available for your use.
*When mounting the device on the wall and connecting it to a DC input
through the access control port, please do not connectthe power adapter
to the Type-C port at the same time.
Option A
1
2
3
4
5
1
2
3
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not
explicitly approved by manufacturer could void your authority
to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two
conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Statement
Specific Absorption Rate (SAR) information:
This Rugged Mobile Terminal meets the government's requirements for exposure to
radiowaves. The guidelines are based on standards that were developed by
independentscientific organizations through periodic and thorough evaluation of
scientific studies.The standards include a substantial safety margin designed to
assure the safety of allpersons regardless of age or health. FCC RF Exposure
Information and Statementthe SAR limit of USA (FCC) is 1.6 W/kg averaged over one
gram of tissue. Devicetypes: Rugged Mobile Terminal has also been tested against this
SAR limit. This devicewas tested for typical body-worn operations with the back of the
device kept 0mmfrom the body. To maintain compliance with FCC RF exposure
requirements, useaccessories that maintain an 0mm separation distance between the
user's body andthe back of the device. The use of belt clips, holsters and similar
accessories shouldnot contain metallic components in its assembly. The use of
accessories that do notsatisfy these requirements may not comply with FCC RF
exposure requirements, andshould be avoided.
