User guide.
WARNING! Reduce the risk of serious injury by reading the User
Guides to your nutribullet
®
Ultra Plus+ Compact Kitchen System
before operating. Save these instructions. Ensure anyone who
uses the nutribullet
®
knows how to do so safely.
Compact Kitchen System
Scan here to
access delicious
recipes for the
nutribullet
®
Ultra Plus+
32
AVOID HEATING AND
OVER-PRESSURIZING CUP:
WARNING! NEVER blend hot,
warm, or carbonated ingredients
or liquid in the nutribullet
®
Cup!
Such use may over-pressurize the
nutribullet
®
Cup, causing the Cup to
separate violently when removed
from the Motor Base or opened,
which may result in bodily injury from
the hot contents or exposed blades
.
• DO NOT blend continuously for
more than one minute.
– Blending causes ingredients to heat
up, which builds pressure in the Cup
over time. Continuous blending for
more than one minute may cause
the Cup to separate, exposing the
Blade, or expel heated contents,
causing injury.
• DO NOT run for more than 6
consecutive 30-second intervals
to prevent the contents from
overheating and pressurizing, which
can lead to a forced separation or
shattering of the Cup resulting in
severe bodily injury, lacerations,
amputations or property damage.
Important safeguards.
When operating your nutribullet
®
Ultra Plus+, remember: SAFETY COMES FIRST.
WARNING! To avoid the risk of serious injury, death, property damage or damage to
your device carefully read all instructions before operating your nutribullet
®
Ultra
Plus+. When using any electrical appliance, basic safety precautions should always
be observed, including the following important information. READ CAREFULLY AND
THOROUGHLY BEFORE OPERATING.
If you let anyone else use your nutribullet
®
Ultra Plus+, make sure that they understand
the health and safety information in this User Guide, as well as any additional safety
or usage instructions provided. Each person using a device should completely read the
User Guide and become familiar with the safe operation of the unit.
– If running continuous cycles, after
each cycle carefully open the cup
to relieve any built-up pressure
before starting the next cycle.
– Allow contents to settle at least 10
to 15 minutes after completing the
last consecutive extraction cycle.
WARNING! DO NOT attempt to
open the Cup if it feels hot or warm
to the touch. See Cup Caution
section for details.
• DO NOT blend anything carbonated
or eervescent — no bubbles.
- Carbonated and eervescent
ingredients (e.g., soda, baking
powder, baking soda, yeast, some
batters, cake mix, dry ice, or
other things that become bubbly)
release gasses that increase
pressure. Pressure from
released gases can cause a
sealed nutribullet
®
Cup to
burst, resulting in possible injury
and/or property damage.
Note: Some protein powders
include eervescent ingredients.
Always check the ingredients of
all supplements before adding.
!
Save these instructions!
FOR HOUSEHOLD USE ONLY
• DO NOT overfill.
- Filling above the MAX line can
result in leakage. The cyclonic
action of the nutribullet
®
requires
space to extract eectively.
Exceeding the MAX line can result
in leakage and may create a
dangerous pressurization which
can cause the Cup and Rapid
Extractor Blade assembly to
separate.
• DO NOT leave blended foods
inside sealed Cup.
– Blended mixtures can spoil and
ferment, increasing pressure when
left inside the Cup, which can lead
to a forced separation or shattering
of the Cup causing possible severe
bodily injury or property damage.
– Always use the To-Go Lid or
transfer to another container for
storage after blending.
CUP CAUTION:
WARNING! NEVER attempt to
open a sealed nutribullet
®
Cup if
it feels hot or warm to the touch.
The contents may be heated and
pressurized, which can cause the
Cup to violently separate when
opened, potentially resulting in
bodily injury. If the Cup feels hot or
warm, take the following steps:
1. LEAVE ALONE, DO NOT OPEN. Leave
the Cup where it is and do not
touch it or allow another individual
to touch. DO NOT attempt to
disengage the Cup from the Motor
Base or separate the Cup from the
Rapid Extractor Blade by applying
heat, force, or prying apart the
components, which may crack
or shatter the Cup and result in
bodily injury.
2. Do not continue to blend.
3. Allow the Cup to cool for at least
30 minutes.
4. After 30 minutes, check if the Cup
is completely cooled. If still warm,
allow to cool more.
5. If cool to the touch, slowly disengage
the Cup from the Motor Base.
6. With the Cup pointed away from
your face and body, use a towel to
slowly untwist the Cup from the Rapid
Extractor Blade and gently release
any residual pressure.
WARNING! If you are still unable
to remove the Cup from the Rapid
Extractor Blade, contact Customer
Service. If you are unable to untwist
the Cup from the Rapid Extractor
Blade, NEVER leave the sealed
contents out for a prolonged period
of time. The contents may ferment
causing the Cup to violently separate,
which can result in bodily injury or
property damage. Dispose of the Cup
and contents properly so you or others
will not be injured if fermentation
causes the Cup to separate.
CUP SAFETY:
WARNING! Always make sure
the Cup is securely locked on the
Motor Base before blending.
The motor will not turn on unless the
Cup is set in the locked position.
• Do not exceed the MAX line.
Exceeding the MAX line can result
in leakage.
• Do not remove the Cup while the unit
is in operation.
• Periodically inspect your nutribullet
®
Ultra Plus+ blender components
for damage or wear that may
impair proper function or create a
safety hazard.
• NEVER operate your nutribullet
®
Ultra
Plus+ if the Cup is empty.
• Do not overfill Cup with ice. Always
use sucient liquid ingredients
when blending.
54
• Do not place on the bottom rack
or use the heat/sanitize cycle of
your dishwasher to wash the Cup
or To-Go Lids.
• NOT MICROWAVE SAFE. Do not
place the Cups and To-Go Lids in
the microwave.
• Do not use the Cup if you detect
cracking, cloudiness, or other
damage. You may purchase new
Cups at nutribullet.com or by
contacting Customer Service.
• Do not use the Rapid Extractor Blade
as a storage lid as the blended
mixture can ferment, increasing
pressure within the Cup that may
cause the Cup and blade to separate,
potentially resulting in bodily injury
and property damage. Use the To-Go
Lid or transfer to a vented container
for storage after blending.
• Do not use after-market replacement
parts for your nutribullet
®
Ultra Plus+.
Use of after-market replacement
parts may result in damage to your
nutribullet
®
or create safety hazards
resulting in bodily injury or damage.
Only order replacement parts
from nutribullet.com or by
contacting Customer Service at:
1 (800) 523-5993, please specify the
model for parts that are compatible
with your unit.
RAPID EXTRACTOR
BLADE SAFETY:
WARNING! BLADES ARE SHARP!
HANDLE WITH CARE TO AVOID
BODILY INJURY. Non-food items or
hard ingredients may damage the
blades. Routinely inspect the blades
and discontinue use if damaged.
Continued use with a damaged
blade or use inconsistent with these
instructions may result in bodily
injury, property damage, or
damage to your unit.
• Do not touch the sharp edges of
the blades. To avoid laceration
injury, do not handle or touch any
blade edge.
• NEVER store any exposed Rapid
Extractor Blade in the Motor Base
unattached to a nutribullet
®
Cup.
An exposed blade can present a
laceration hazard.
• ALWAYS securely tighten the Rapid
Extractor Blade to the Cup to
prevent leakage or cup separation
from the blade.
• Do not attempt to disengage the
Cup from the Motor Base if the Cup
starts to leak during blending. Allow
the motor to come to a complete
stop before removing the Cup.
• Do not crush ice. Your nutribullet
®
Ultra Plus+ is not intended to be used
as an ice crusher.
• Do not leave any non-food items in
the Cup when blending.
REMOVE ALL UTENSILS FROM THE
CUP WHICH MAY SHATTER THE
CUP AND CAUSE SEVERE
LACERATION INJURIES.
• Do not blend stone fruit in this
appliance unless pits/seeds have
been removed. Fruit pits may
damage the Cup. In addition, apple
seeds and the pits of cherries, plums,
peaches, and apricots contain a
chemical known to release cyanide
into the body when ingested.
• DO NOT USE the Rapid Extractor
Blade for grinding dry ingredients
such as grains, cereal, or coee, as
this may damage the motor and/or
the blade.
• Do not remove the Cup until blades
have come to a complete stop.
Removing before the blades come to
a complete stop can cause damage
to the Rapid Extractor Blade
coupling or motor gear.
• Always POWER OFF and UNPLUG
the unit when assembling,
disassembling, changing
accessories, or cleaning.
• Do not overload the Cup by
exceeding the MAX line. The blades
may stop turning if the Cup is
overloaded. If this occurs, turn o
the unit, empty contents down to the
Max line, reattach the Cup, and
resume blending.
• AVOID CONTACT WITH MOVING
PARTS! Keep hands and utensils out
of and away from the Blade while
blending to reduce the risk of
severe personal injury or damage
to the unit.
• DO NOT attempt to defeat any
safety interlock mechanisms.
• NEVER place the Rapid Extractor
Blade on the bottom rack or use
the heat/sanitize cycle of your
dishwasher when cleaning.
• Periodically inspect the blades for
damage. DO NOT use the Rapid
Extractor Blade if the blades do
not rotate freely or if the gasket is
missing or damaged.
• The Rapid Extractor Blade is
designed for longevity and comes
with a 5-year warranty.
• We recommend replacing at least
every 5 years.
PROCESSOR ATTACHMENT
PRECAUTIONS:
Proper operation of the nutribulle
t®
Ultra Plus+ Processor Attachment is
essential for safety. Using the Ultra Plus+
Processor Attachment inconsistent with
these instructions may result in bodily
injury, property damage, or damage to
your unit.
WARNING! BLADES AND DISCS
ARE SHARP! HANDLE WITH CARE.
• Do not attempt to remove the
Work Bowl or Lid while the unit is
in operation.
• Avoid contact with moving parts.
ALWAYS make sure that the Motor
Base Is powered o and the blades
are completely stopped before
removing any attachment.
• After use, unplug the unit from
the outlet and ensure that the
blades have come to a complete
stop before removing the lid and
disassembling parts, and before
cleaning. To unplug, grasp the plug
and pull from the outlet. Never pull
from the power cord.
WORK BOWL AND FEED
CHUTE SAFETY:
• Ensure the Processor Attachment is
securely attached to the nutribullet
®
Ultra Motor Base. The Work Bowl
will audibly “click” when it is securely
attached to the Motor Base. When
attaching the Work Bowl Lid, make
sure the arrow on the Lid aligns with
the arrow on the Work Bowl.
• NEVER open the Work Bowl Lid while
the unit is operating or when the
Blades or Discs are still moving. Doing
so may pose a risk of severe bodily
injury or property damage. A scraper
or spatula may be used only when the
Processor Attachment is not running
and the unit is POWERED OFF.
• NEVER place hands, fingers, or
utensils inside the Work Bowl or Feed
Chute when the Blades or Discs are
moving. Always allow the Blades or
Discs to come to a complete stop
before handling.
• Do not allow processed ingredients to
exceed the maximum fill line of
the Work Bowl.
• Do not remove the Processor
Attachment until the Blades have
come to a complete stop.
NOTE: The Work Bowl will not
disengage from the Motor Base
until the Work Bowl Lid is removed.
First, remove the Work Bowl Lid, then
disengage the Work Bowl from the
Motor Base. Attempting to remove the
attachment before the Blades come
to a complete stop or failing to first
remove the Work Bowl Lid can cause
damage to the attachment or unit.
• NEVER use your hands, fingers, or
utensils to push food down into the
Feed Chute or Work Bowl. Doing so
may result in severe bodily injury or
damage to the machine. Use only
the Food Pusher included with your
76
Processor Attachment to move
ingredients down the Feed Chute.
• DO NOT overload the Feed Chute
with ingredients or use excessive
force on the Food Pusher to push
food down the Feed Chute. This
may cause the Blades or Discs to
seize, which may cause the motor to
overheat or the Work Bowl to fracture
and break. If the Blades or Discs
cease to function, turn o and unplug
the unit and wait until all moving
parts — Blades included — come
to a complete stop. Clear out the
contents from the Feed Chute before
reattaching and resuming blending.
• For best results, power on your
Processor Attachment before adding
ingredients to the Feed Chute.
Use the Food Pusher to slowly and
steadily move ingredients toward the
Blades/Discs. Always add ingredients
to the Chute at a slow, steady pace.
GENERAL BLADE & DISC SAFETY:
WARNING! BLADES AND DISCS
ARE SHARP! DO NOT TOUCH THE
SHARP EDGES OF THE BLADES
OR DISCS. HANDLE THE BLADES
AND DISCS CAREFULLY BY THE
CENTER PLASTIC AREA TO AVOID
LACERATION, AMPUTATION, OR
OTHER BODILY INJURY.
• Always POWER OFF and UNPLUG
the unit and wait until the Blades
or Discs come to a complete stop
before assembling, disassembling,
changing accessories, or cleaning
to avoid laceration or other
bodily injury.
WARNING! ALWAYS REMOVE
THE BLADES OR DISCS CAREFULLY
BEFORE ACCESSING THE FOOD
FROM THE WORK BOWL. NEVER
ATTEMPT TO REMOVE THE BLADES
OR DISCS BY TILTING THE WORK
BOWL FOR THE PURPOSE OF
HAVING THE BLADE OR DISC DROP
OUT ONTO YOUR HAND, DOING SO
MAY CAUSE SEVERE LACERATION
INJURIES, AMPUTATION OR BODILY
INJURIES.
• AVOID CONTACT WITH MOVING
PARTS! Do not attempt to defeat
any safety interlock mechanisms.
• DO NOT leave non-food items
(such as a spoon or fork) or use
hard ingredients in your Processor
Attachment. Doing so can damage
your nutribullet
®
device, which
may result in bodily injury or
property damage.
• NEVER LEAVE OR STORE AN
EXPOSED BLADE OR DISC
DIRECTLY ON TOP OF THE MOTOR
BASE. Exposed Blades and Discs
present a safety hazard that may
result in severe laceration injuries.
Always place Blades and Discs
inside of the Work Bowl and
cover with the Work Bowl Lid
when storing.
• Do not use the Blades or Discs for
grinding dry ingredients such as
grains, cereal, or coee, as this may
damage the motor, Blades, and
Discs. Use of dry ingredients may
cause the motor to overheat.
• Use only the top rack when using
the dishwasher to clean Blades,
Discs, and any other nutribullet
®
part or accessory. NEVER wash any
nutribullet
®
part or accessory on the
bottom rack of the dishwasher or
use the heat/sanitize cycle.
WARNING! ALWAYS USE
EXTREME CARE AND EXERCISE
CAUTION WHEN CLEANING THE
BLADES OR DISCS BY HAND. DO
NOT TOUCH THE SHARP EDGES OF
THE BLADES OR DISCS
WITH YOUR HANDS OR FINGERS.
DOING SO MAY CAUSE SEVERE
LACERATION INJURIES.
• Routinely inspect your nutribullet
®
device, Blades, and Discs, and
discontinue use if damaged.
Immediately discontinue use if the
device or any part appears to be
damaged. Continued use with a
damaged nutribullet
®
device or
part, or use inconsistent with these
instructions may result in bodily
injury, property damage, or further
damage to your unit. For assistance
with a damaged device or part,
contact Customer Service at
1 (800) 523-5993.
COFFEE & SPICE GRINDER
ATTACHMENT PRECAUTIONS:
WARNING! READ ALL
INSTRUCTIONS. FAILURE TO
FOLLOW ALL INSTRUCTIONS
REGARDING THE USE OF YOUR
NUTRIBULLET
®
ULTRA PLUS+
BLENDER AND COFFEE & SPICE
GRINDER ATTACHMENT
MAY RESULT IN SERIOUS
PERSONAL INJURY, DEATH, OR
PROPERTY DAMAGE.
• Always check the device for any
foreign objects or damage
before use.
• NEVER add liquids to the Coee &
Spice Grinder Attachment. Doing so
can damage the product.
• Do not grind ice. The Coee & Spice
Grinder Attachment is not intended
to be used as an ice crusher. Doing
so can damage the product and may
cause serious injuries and damage
your unit.
• Do not use the Coee & Spice
Grinder Attachment for anything
other than its intended use.
• Do not place the Coee & Spice
Grinder Attachment in a microwave,
conventional oven, or air fryer, or on
a stovetop.
• The Coee & Spice Grinder
Attachment is top-rack dishwasher-
safe only. NEVER wash any
nutribullet
®
part or accessory on the
bottom rack of the dishwasher or use
the heat/sanitize cycle. NEVER place
the Motor Base in the dishwasher.
• Do not use the Coee & Spice
Grinder Attachment as a storage
container or store it in a refrigerator
or freezer.
• Avoid contact with moving parts.
ALWAYS make sure that the Motor
Base is powered o and the blades
have come to a complete stop
before removing the The Coee &
Spice Grinder Attachment.
GENERAL USE AND SAFETY:
WARNING! FAILURE TO FOLLOW
ALL INSTRUCTIONS REGARDING
THE USE OF YOUR NUTRIBULLET
®
ULTRA PLUS+ MAY RESULT IN
SERIOUS PERSONAL INJURY,
DEATH, OR PROPERTY DAMAGE.
BE AWARE OF POSSIBLE HAZARDS
WHEN USING OR STORING YOUR
NUTRIBULLET
®
ULTRA PLUS+.
• NEVER blend hot, warm, or
carbonated ingredients in the
nutribullet
®
Cup. This may
pressurize contents, causing them
to erupt upon opening, which can
result in serious bodily injury or
property damage.
• Do not use this blender for anything
other than its intended use.
• Close supervision is necessary when
any appliance is used by or near
children to ensure they do not play
with the appliance. Keep cord out of
reach of children.
• This appliance is not intended for
use by persons (including children)
with reduced physical, sensory,
or mental capabilities, or lack of
experience and knowledge, unless
they are closely supervised and
instructed concerning use of the
appliance by a person responsible
for their safety.
• NEVER LEAVE THE NUTRIBULLET
®
UNATTENDED WHILE IT IS IN USE.
• Do not place your nutribullet
®
blender on uneven or
unstable surfaces.
98
• The risk of fire, shock or damage
to nutribullet
®
Ultra Plus+ during
cleaning can be reduced by taking
the following precautions:
– Unplug and turn your device o
before cleaning.
– Only clean the exterior of
your device.
– Clean your device with a dry cloth.
– Do not attempt to clean by
immersing in water or other
cleaning liquids. Only gently wipe
and dry with a clean cloth.
• Do not place any of the nutribullet
®
Ultra Plus+ parts or Attachments in
a microwave, conventional oven, air
fryer or stovetop pot, or immerse in
boiling water, as this will damage
the part and may cause severe
bodily injury.
• NEVER use the sanitize or heat
cycle on any nutribullet
®
part or
accessory. This may cause warping
and possibly create a hazardous
conditions leading to severe injury.
• NEVER place a nutribullet
®
Cup or
Attachments in the freezer or use as
a storage container in the freezer.
• Make sure your nutribullet
®
Ultra
Plus+ is powered o and the motor
and blades are completely stopped
before removing or cleaning unit.
• Use of incompatible parts or
aftermarket parts may result in
damage to your nutribullet
®
Ultra
Plus+ or the Attachments and may
create safety hazards that may
create a risk of personal injury or
property damage. When ordering
replacement parts, always use
genuine nutribullet
®
parts and
accessories from nutribullet.com or
contact Customer Service at
1 (800) 523-5993.
• Periodically inspect your nutribullet
®
Ultra Plus+ components for damage
or wear that may impair proper
function or present a danger or
safety hazard. Discontinue use if
you detect cracking, cloudiness,
or damage to the Cups or other
parts. Ensure that the blades to the
Rapid Extractor Blade rotates freely
and that gasket is not missing or
damaged. Make sure that the Motor
Base is unobstructed and clean.
Always follow the maintenance
instructions in this user guide.
Never operate your nutribullet
®
Ultra Plus+ with damaged parts or
components. If your nutribullet
®
Ultra
Plus+ malfunctions, is damaged
or compromised in any way,
immediately discontinue use and
contact customer service at
1 (800) 523-5993 with any
comments, questions, or concerns.
ELECTRICAL SAFETY:
• Modification, improper use, and
failure to follow the instructions for
proper set up, use, and care of your
nutribullet
®
Ultra Plus+ blender can
increase the risk of serious personal
injury, death, or property damage.
• NEVER use the unit in locations with
dierent electrical specifications or
plug types.
• NEVER use the unit with a voltage
converter device as it may cause
electrical shorting, fire, or electric
shock, resulting in personal injury or
product damage.
• Do not use the unit in an area t
hat is wet or anywhere it could
become wet.
• Do not attempt to plug the unit into
an electrical outlet with wet hands.
• Do not use if the cord, plug, or Motor
Base was immersed in water or
other liquids.
• Do not modify the electrical cord
in any way.
• Do not operate with a damaged
electrical cord or plug. The electrical
cord and plug are not suitable
for replacement. If damaged, the
appliance should be replaced.
Contact Customer Service for
assistance at: 1 (800) 523-5993.
• Do not allow or place the electrical
cord near or touching any hot
surfaces, heat source, or flame,
including the stove.
• Do not allow the electrical cord to
hang over the edge of the table
or counter.
• Do not pull, twist, or damage the
power cord.
• Overloading the Cup with ice or
other hard ingredients, or use
without sucient liquids may
overheat the motor and engage
the thermal breaker. If the internal
thermal breaker shuts o the
motor, unplug the Motor Base
and let it cool for an hour before
attempting to use it again. The
thermal breaker will reset when the
unit is unplugged and the thermal
breaker cools down.
• Always UNPLUG the nutribullet
®
Ultra Plus+ when it is not in use, and
when assembling, disassembling,
changing accessories, or cleaning.
• This appliance has a polarized plug
(one blade is wider than the other).
To reduce the risk of electric shock,
this plug will fit in a polarized outlet
only one way. If the plug does not fit
fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified
electrician. Do not modify the plug
in any way.
• DO NOT USE OUTDOORS.
VENTILATION:
• NEVER obstruct the ventilation
openings on the bottom of the
Motor Base of your nutribullet
®
Ultra
Plus+. Openings on the bottom of
the Motor Base should be free of
dust or lint and never obstructed.
Obstructing the ventilation openings
may overheat the motor and result
in a fire, increasing the risk of
serious personal injury, death, or
property damage.
• ALWAYS operate the nutribullet
®
on a level surface, leaving
unobstructed space beneath and
around the Motor Base to permit
proper air circulation. Slots on
the bottom of the Motor Base are
provided for ventilation to ensure
reliable operation and to prevent
motor overheating.
• NEVER place your nutribullet
®
Ultra
Plus+ on top of flammable materials
such as newspapers, tablecloths,
napkins, dishtowels, place mats, or
other similar types of materials.
MEDICAL SAFETY:
WARNING! ALWAYS CONSULT
YOUR PHYSICIAN REGARDING
HEALTH AND NUTRITION CONCERNS
AND ADVICE. THE INFORMATION
CONTAINED IN THIS USER GUIDE,
ACCOMPANIED RECIPE GUIDE, AND/
OR ONLINE RECIPES ARE GENERAL
SUGGESTIONS AND IDEALS AND
ARE NOT MEANT TO REPLACE THE
ADVICE OF YOUR PHYSICIAN.
MEDICATION INTERACTIONS:
• If you are taking any medication,
especially cholesterol-lowering
medication, blood thinners, blood
pressure drugs, tranquilizers, or
antidepressants, please check with
your physician before trying any of
the smoothie recipes contained in the
Recipe Guide or online recipes.
Save these
instructions!
1110
Contents.
2 Important safeguards
12 What’s included
14 Assembly
17 Control panel
18 Using your nutribullet
®
Ultra Plus+
22 Troubleshooting
23 Cup maintenance & storage
26 Using your nutribullet
®
Ultra Plus+
Processor Attachment
27 Using the Chopping Blade
30 Using the Reversible Slice/Shred Disc
33 Removing food from the Processor Attachment
35 Troubleshooting
37 Maintenance & storage
40 Using your nutribullet
®
Ultra Plus+
Coffee & Spice Grinder Attachment
43 Troubleshooting
44 Maintenance & storage
46 General care & maintenance.
48 nutribullet
®
Ultra Plus+ Limited
Warranty & Product registration
48 nutribullet
®
Ultra Plus+
51 nutribullet
®
Ultra Plus+ Extractor Blade
54 nutribullet
®
Ultra Plus+ Product Registration
Thank you for purchasing the nutribullet
®
Ultra Plus+ Compact Kitchen System.
1312
To see our full list of nutribullet
®
accessories, please visit nutribullet.com
What’s included.
work bowl
work bowl lid
chopping blade
processor base
with blade adapter
reversible
slice/shred disc
food pusher
Work bowl Empty
Chopping blade (overhead)
Slice shred disc
Food Pusher (straight on)
grinder blade
motor base
grinding cup
Grinder Blade
Grinder Cover
Motor base
32oz cup
32 oz cup
24oz double
walled cup
24 oz cup
2 to-go lids
2 to-go lids
rapid extractor
blade
Extractor blade
Food Processor Bowl + Lid Empty
1514
Assembly guide.
processor
base with
blade
adapter
work bowl
work bowl lid
reversible slice/
shred disc
motor base
chopping blade
Assembly guide illustration: Food Processor
Processor
Attachment
Blender
nutribullet
®
cup
rapid extractor blade
motor base
suction cup feet
1716
grinder blade
motor base
grinding cup
Assembly guide illustration: Grinder
Coffee & Spice Grinder Attachment
Control panel.
OFF
PULSE
The Control Panel is
not illuminated.
BLEND
After twisting the Blade/Cup
assembly onto the Motor Base,
the Control Panel will appear.
Touch the illuminated Solid
Circle icon on the Control Panel
to activate the automatic
30-second blending program.
After twisting the Blade/Cup
assembly onto the Motor Base,
the Control Panel will appear.
Press and hold the Dashed
Circle on the Control Panel to
activate the pulse feature.
For short, intermittent pulses,
tap the Pulse icon. For longer
pulses, tap and hold the
Pulse icon until your desired
consistency is reached.
Control panel - O
Control panel - blend
1918
WARNING: KEEP
THESE IMPORTANT
SAFEGUARDS IN
MIND WHEN USING
THE NUTRIBULLET
®
:
Using your nutribullet
®
Ultra Plus+.
Creating too much pressure
in the nutribullet
®
Cup can
result in injury from hot
contents, flying components,
or blade exposure.
• DO NOT blend hot or
warm ingredients,
carbonated liquids, or
eervescent ingredients.
• Do not overfill the Cup.
• DO NOT run for more than
6 consecutive 30-second
intervals to prevent the
contents from overheating
and pressurizing, which
can lead to a forced
separation or shattering of
the Cup resulting in severe
bodily injury, laceration
or amputation. If running
continuous cycles, after
each cycle carefully open
the cup to relieve any
built up pressure before
starting the next cycle. After
running multiple consecutive
extraction cycles allow
contents to settle for
10 to 15 minutes before
opening the Cup.
• See Avoid Heating and
Over-Pressurizing Cup
(pg. 2) for details.
• DO NOT attempt to open
a sealed nutribullet
®
Cup if
it feels hot or warm to the
touch. The contents may
be heated and pressurized,
causing the Cup to violently
separate when opened, and
potentially resulting in bodily
injury. See Cup Caution
(pg. 3) for details.
• Blades are sharp!
Handle with care to avoid
bodily injury. NEVER store
any exposed Rapid
Extractor Blade in the
Motor Base unattached to a
nutribullet
®
Cup.
1 Review all warning and
caution statements in the
Important Safeguards
section (pg. 2-10) and on
the previous page before
proceeding to Step 2.
2 Place the Motor Base on
a clean, dry, level surface
such as a counter or table.
3 Add ingredients and liquid
to the nutribullet
®
Cup.
WARNING! To
avoid leakage and
over-pressurizing,
do not overfill beyond
the MAX line.
Direction #3
4 Twist the Rapid Extractor
Blade onto the nutribullet
®
Cup until it’s tightly sealed.
Direction #4
WARNING! Rapid
Extractor Blade is sharp.
Handle with care.
2120
6 Flip the Cup downward
and set it onto the
Motor Base.
Direction #6
5 Plug the Motor Base’s
Power Cord into an
electrical outlet.
Direction #5
7 Twist the Cup clockwise
onto the Motor Base to
lock it into place. (A “click”
signals that the Cup is
locked.) This will illuminate
the Control Panel.
Direction #7
8 Pressing the Solid Circle
will start an automated
blending cycle. When the
blending cycle is activated,
it will automatically
stop after 30 seconds.
Pressing and holding the
Dashed Circle will pulse
blend your ingredients.
Release the Dashed Circle
to stop blending.
Direction #8
9 Twist the Cup
counterclockwise to
unlock and remove it from
the Motor Base. You will
hear a “click” when the
Cup unlocks. Enjoy!
Direction #9
WARNING! NEVER blend
hot, warm, or carbonated
ingredients or liquid in the
nutribullet
®
Cup! Such use
may over-pressurize the
nutribullet
®
Cup, causing the
Cup to separate violently
when removed from the
Motor Base or opened, which
may result in bodily injury
from the hot contents or
exposed blades.
NEVER apply heat or force, or
attempt to pry apart the Cup
from the Rapid Extractor
Blade. Doing so may crack
or shatter the Cup resulting
in severe bodily injury. Allow
the contents of the Cup to
settle down for at least 30
minutes before attempting
to open again. If still
unable to open, contact
Customer Service.
22 23
Troubleshooting.
PROBLEM:
The unit does not power
on OR the Control Panel
does not appear.
SOLUTIONS:
• Make sure the Power
Cord is plugged into an
electrical outlet, and that
outlet has power.
• Make sure that the Cup/
Blade assembly is securely
attached to the Motor Base.
You will hear a ‘Click’ when
they are securely attached.
PROBLEM:
The Control Panel
flashes continuously.
SOLUTIONS:
• You have exceeded 6
consecutive blend cycles in
a 6-minute time frame, OR
the unit has overheated. If
this has occurred, unplug the
unit and allow it to cool down
for at least 15 minutes before
attempting to use again.
PROBLEM:
The unit has become very loud
during the blending cycle.
SOLUTIONS:
• Check that you have not
exceeded the MAX fill line
on the Cup when filling with
ingredients. Overfilled Cups
can cause strain on the
motor which will result in an
increased noise level.
PROBLEM:
There is an odor coming from
the Motor Base when it is in use.
SOLUTIONS:
• During the first few uses of
the unit, there may be a smell
emitted from the Motor Base,
but this is normal with the
first use of the product and
should not cause alarm.
• If you notice a smell after
using the product several
times, check to ensure that
you have not exceeded the
MAX fill line on the Cup with
ingredients. Overfilled Cups
can cause strain on the motor
which can result in an odor.
Cup maintenance
& storage.
WARNING: KEEP
THESE IMPORTANT
SAFEGUARDS IN
MIND WHEN USING
THE NUTRIBULLET
®
:
• Always power o and
unplug your nutribullet
®
Ultra Plus+ when not in
use or when assembling,
disassembling, changing
accessories, or cleaning.
• Always wait until the motor
comes to a complete stop
before removing the Cup,
Attachments, or when
handling the unit.
• Do not place Cups,
Attachments, and To-Go Lids
in the microwave, they are
not microwave safe.
• NEVER place the Rapid
Extractor Blade, Cups,
Attachments or To-Go Lids
on the bottom rack or use
the heat/sanitize cycle of
your dishwasher when
cleaning. It may cause
warping and possible
safety hazards.
• Do not attempt to clean the
Motor Base by immersing
in water or other cleaning
liquids. Gently wipe and dry
with a clean cloth.
• Do not place any parts or
accessories in a microwave,
conventional oven, air fryer
or stovetop pot, or immerse
in boiling water to clean or
sanitize, as this will damage
the part.
• Make sure that the Motor
Base ventilation areas are
unobstructed and clean.
• Periodically inspect your
nutribullet
®
Ultra Plus+
components for damage or
wear that may impair proper
function or present a danger
or safety hazard. Never
operate your nutribullet
®
Ultra Plus+ with damaged
parts or components:
- Discontinue use if
you detect cracking,
cloudiness, warping, or
damage to the Cups or
Processor Work Bowl.
2524 25
• NEVER attempt to use
your nutribullet Ultra if it
malfunctions, dropped,
appears to be damaged
or compromised in any
manner. Contact Customer
Service for assistance at:
1 (800) 523-5993.
• NEVER use after-market
replacement parts for your
nutribullet
®
Ultra Plus+.
Aftermarket parts are
not made to nutribullet
®
specifications and may
damage your unit or
cause serious injury. Use
only genuine nutribullet
®
attachments/accessories
specifically designed for
your nutribullet
®
Ultra Plus+
blender by calling Customer
Service at: 1 (800) 523-5993.
24
1 Once blending is complete,
make sure your nutribullet
®
Ultra Plus+ Motor Base is
powered o and unplugged
from its outlet.
2 Detach the nutribullet
®
Cup
and Rapid Extractor Blade
from the Motor Base.
3 Clean the individual
components as follows:
Cleaning: #1
Cleaning #2
EXTRACTOR BLADES:
• Rinse the Rapid
Extractor Blade with
warm, soapy water.
• Use a small brush or sponge
dampened in soapy water to
remove any residue on the
Rapid Extractor Blade.
NOTE: It’s best to clean the Rapid
Extractor Blade immediately after
use to avoid the buildup of residue.
MOTOR BASE:
• Use a sponge or dishcloth
dampened with soapy water
to clean the surface of the
Motor Base.
• Use a small brush to scrub
the actuator system of the
Motor Base.
CUPS & TO-GO LIDS:
• Cups and To-Go Lids are
dishwasher-safe. Rinse or
scrub beforehand to remove
any debris.
WARNING! NEVER place
the Rapid Extractor Blade,
Cups or To-Go Lids on the
bottom rack or use the
heat/sanitize cycle of your
dishwasher when cleaning,
as this may cause warping
and possible safety hazards.
For replacement
parts.
Visit nutribullet.com/shop/
accessories or call customer
service at 1 (800) 523-5993.
STUCK INGREDIENTS:
• For stuck ingredients on
Cups or Rapid Extractor
Blades, fill with room
temperature water to the
MAX line and add 1-2 drops
of dish soap.
• Twist on the Rapid Extractor
Blade and blend for 20-30
seconds to loosen debris
enough to scrub away with
soap and water.
STORAGE:
• Always store your
nutribullet
®
Ultra Plus+
upright without any objects
placed on top of it. Store
accessories in a safe place
until use.
• NEVER leave an exposed
blade in the Motor Base
when storing.
27
1 Place the Motor Base, Work
Bowl, and Processor Base
& Blade Adapter on a flat
clean and dry surface.
2 Remove the Work Bowl
Lid from the Work Bowl,
and slide the Work Bowl
over the Processor Base
& Blade Adapter. Turn
the Work Bowl so that the
bowl sits flush. The handle
of the Work Bowl should
sit opposite of the lid-
locking mechanism on the
Processor Base & Blade
Adapter. Twist the Work
Bowl clockwise to lock onto
the Processor Base
& Blade Adapter.
Place the Motor Base and Work Bowl on a flat, clean, and dry surface.
Using the Chopping Blade:
chop, mix, and mince food.
3 Lower the Chopping Blade
atop the central shaft of the
Work Bowl and push down
to secure into place.
WARNING: The blades are
sharp, handle with care.
WARNING: TO REDUCE
THE RISK OF SEVERE
BODILY INJURIES OR
PROPERTY DAMAGE,
ALWAYS KEEP IN MIND:
• Always read the instructions
before operating.
• Blades and discs are sharp,
carefully handle using the
center plastic area.
• Do not overload the Feed
Chute or use excessive force
on the Food Pusher. It is
recommended to first start the
unit and then place the food
into the Food Chute.
• NEVER use your hands, fingers
or utensils to push ingredients
down towards the blade, use
only the Food Pusher.
• NEVER leave the blades or
discs exposed when storing.
ALWAYS store blades and
discs in the Work Bowl with
the Work Bowl Lid attached.
• Always remove the Blades or
Discs before accessing the
food from the Work Bowl.
26
Using your nutribullet
®
Ultra
Plus+ Processor Attachment.
WARNING: NEVER ATTEMPT
TO REMOVE THE BLADES OR
DISCS BY TILTING THE WORK
BOWL FOR THE PURPOSE
OF HAVING THE BLADE
OR DISC DROP OUT ONTO
YOUR HAND. DOING SO MAY
CAUSE SEVERE LACERATION
INJURIES, AMPUTATION, OR
BODILY INJURIES.
2928
6 Attach the Work Bowl Lid.
Place the Work Bowl Lid on
top of the Work Bowl and
align the locking tab with
the locking mechanism on
the Processor Base & Blade
Adapter. Push the Work
Bowl Lid down while twisting
Attach the Work Bowl Lid. Aligning the arrow on the Work Bowl Lid
with the arrow on the Work Bowl and twist the Lid clockwise.
Place the Work Bowl onto the unplugged Motor Base. Twist clockwise.
The Work Bowl will click when locked into place.
4 Prepare ingredients and
add them to the Work Bowl.
Remove seeds, stems, and
other non-edible pieces. Cut
large items into 1-to-2-inch
pieces before processing.
WARNING: DO NOT fill
beyond the MAX line.
5 Place the Work Bowl &
Processor Base onto the
unplugged Motor Base.
With the Work Bowl handle
facing to the right side of
the Motor Base, lower the
Work Bowl onto the Motor
Base and turn clockwise.
The Processor Base will
click when locked into place.
clockwise to lock the lid into
place. Plug in the Motor
Base. The control panel will
illuminate. The Processor
Attachment will not work
unless both the Processor
Base and Work Bowl Lid are
properly locked into place.
9 After processing, wait until
the blades have come to
a complete stop before
attempting to remove
the food. To safely and
properly remove/access
the food, see the steps
on page 33.
7 Choose your processing
method: press the
Solid Circle to begin an
automated processing
cycle of 30 seconds, or
press and hold the Dashed
Circle for your desired
amount of time to pulse
or process manually.
8 You may pour liquid through
the top chute ONLY when
the Processor Attachment is
powered o and the blades
are at a complete stop. (DO
NOT fill ingredients beyond
the Work Bowl’s MAX line).
Choose your processing method
Choose your processing method
WARNING: Keep fingers
away from the Chopping
Blade’s sharp edges. Only
handle the chopping
blade using the plastic
center hub to avoid severe
bodily injuries, lacerations,
or amputation.
WARNING: Do not remove
the Blades or Discs by
tilting the Work Bowl and
having the Blade or Disc
drop out onto your hand.
3130
Using the Reversible Slice/Shred Disc:
slice or shred ingredients.
1 Place the Motor Base,
Work Bowl, and Processor
Base & Blade Adapter on a
flat clean and dry surface.
2 Remove the Work Bowl
Lid from the Work Bowl,
and slide the Work Bowl
over the Processor Base
& Blade Adapter. Turn
the Work Bowl so that the
bowl sits flush. The handle
of the Work Bowl should
sit opposite of the lid-
locking mechanism on the
Processor Base & Blade
Adapter. Twist the Work
Bowl clockwise to lock onto
the Processor Base &
Blade Adapter.
3 The Slice/Shred Disc is
reversible, with one side
labeled for shredding and
the other for slicing. Install
the Disc on central shaft
of the Work Bowl with the
desired function facing up.
Place the Motor Base and Work Bowl on a flat, clean, and dry surface.
Locate The Disc will be nearly
flush with the top rim of the
Work Bowl when installed
properly.
WARNING: The Disc blades
are sharp, handle with care.
4 Place the Work Bowl &
Processor Base onto the
unplugged Motor Base.
With the Work Bowl handle
facing to the right side of
the Motor Base, lower the
Work Bowl onto the Motor
Base and turn clockwise.
The Processor Base will
click when locked into place.
5 Attach the Work Bowl Lid.
Place the Work Bowl Lid on
top of the Work Bowl and
align the locking tab with
the locking mechanism
on the Processor Base &
Blade Adapter. Push the
Work Bowl Lid down while
twisting clockwise to lock
the lid into place. Plug in
the Motor Base. The control
panel will illuminate. The
Processor Attachment will
not work unless both the
Processor Base and Work
Bowl Lid are properly
locked into place.
Place the Work Bowl onto the unplugged Motor Base
and twist clockwise to secure.
Attach the Work Bowl Lid
3332
8 After processing, wait
until the Disc has come to
a complete stop before
attempting to remove the
food. To safely and properly
remove/access the food,
see the steps on page 33.
7 Choose your processing
method: press the Solid
Circle to begin an automated
slicing/shredding cycle of 30
seconds, or press and hold
the Dashed Circle for your
desired amount of time to
pulse or slice/shred manually.
WARNING: Do not apply
excessive pressure on the
Food Pusher.
6 Plug in the Motor Base.
The Control Panel will
illuminate.
Plug in the Motor Base. The Control Panel will illuminate.
Choose your processing method
Removing food from the Processor Attachment:
1 Remove the Work Bowl
Lid: Turn the Lid counter-
clockwise to unlock, then
lift from the Work Bowl.
3 Carefully remove the
Chopping Blade or Slice/
Shred Disc from the Work
Bowl by grasping the central
plastic knob of the Slice/
Shred Disc or Chopping Blade
and gently pulling upwards.
2 Remove the Work Bowl &
Processor Base:
Turn the Work Bowl &
Processor Base counter-
clockwise to unlock, then lift
from the Motor Base.
WARNING: Keep fingers
away from the Chopping
Blade and Slice/Shred
Disc’s sharp edges. Only
handle the Disc using the
plastic center hub to avoid
severe bodily injuries,
lacerations, or amputation.
Choose your processing method
3534
5 To remove the Work Bowl
from the Processor Base
& Blade Adapter, grasp
the Processor Base from
the bottom with one hand,
and with the other hand
grasp the handle of the
Work Bowl. Twist the Work
Bowl counter-clockwise and
carefully lift the Work Bowl
o of the Processor Base &
Blade Adapter.
4 Once the Chopping
Blade or Slice/ Shred
Disc are removed, use a
spoon or spatula to remove
ingredients from the
Work Bowl.
WARNING: NEVER attempt
to remove the Blade or
Disc by tilting the Work
Bowl for the purpose of
having the Blade or Disc
drop out onto your hand.
DOING SO MAY CAUSE
SEVERE LACERATION
INJURIES, AMPUTATION
OR BODILY INJURIES.
Troubleshooting.
PROBLEM:
My nutribullet
®
Ultra
Plus+ won’t turn on.
SOLUTIONS:
• Check your outlet. Ensure
that the Motor Base is
plugged in properly.
• Check that the Work Bowl
is properly attached to the
Motor Base. The Work Bowl
will audibly “click” when it
is securely attached to the
Motor Base.
• Check that the arrows on the
Work Bowl Lid are aligned
with the arrows on the
Work Bowl.
• If the other possibilities
are determined not to be
the issue, it’s likely that the
unit’s thermal breaker was
engaged. Allow the unit to
cool for at least 30 minutes
before attempting to
use again.
PROBLEM:
My nutribullet
®
Ultra Plus+
won’t turn o.
SOLUTIONS:
• Unplug the power cord from
the outlet. Make sure that
the Motor Base is powered
o and that the blades
have come to a complete
stop before removing the
Processor Attachment.
PROBLEM:
The ingredients are not
chopping properly.
SOLUTIONS:
• Ensure that the Blade
Assembly and Chopping
Blade are properly attached.
• Ensure that the ingredients
do not exceed the MAX fill
line on the Work Bowl.
• Ensure sure that the
ingredients are suitable
for chopping.
• Try chopping using the
Pulse Mode. Select, hold,
and release the Dashed
Circle on the Control Panel
in succession until your
ingredients are cut to
satisfaction.
Place the Work Bowl onto the unplugged Motor Base
and twist clockwise to secure.
3736
PROBLEM:
The ingredients are not slicing
or shredding properly.
SOLUTIONS:
• Make sure that the desired
Disc function (slicing or
shredding) is installed
facing up.
• Make sure that the Blade
Assembly and Disc are
properly attached.
• Make sure the Disc is set in
the correct position, with the
hash marks on the Disc and
Blade Adapter are aligned.
The Disc should be nearly
flush with the top rim of the
Work Bowl.
• Make sure that the Feed
Chute is not overfilled with
ingredients. For best results,
start processing before
inserting ingredients into
the Feed Chute and allow
the ingredients to move
downwards naturally. Do not
apply excessive pressure on
the Food Pusher.
• Make sure that the
ingredients are suitable for
slicing/shredding.
• Try slicing/shredding using
Pulse Mode. Select and hold
the Dashed Circle on the
Control Panel for pulse. Hold
the Dashed Circle icon until
your ingredients are cut to
satisfaction.
Ultra Plus+
Processor Attachment
maintenance & storage.
CLEANING:
WARNING: FOLLOW THESE
IMPORTANT SAFEGUARDS
WHEN USING THE ULTRA
PLUS+ PROCESSOR
ATTACHMENT:
• SHARP BLADES, ALWAYS use
caution when handling or
cleaning the Blade or Disc.
• NEVER leave an exposed Blade
or Disc on the Motor Base.
• ALWAYS store the Blade
and Disc in the Processor
Attachment with the Work
Bowl Lid attached.
• NEVER place the Food
Processor attachment
or any of its parts in
the microwave.
1 Unplug the Motor Base
from the outlet.
2 Make sure the Blade or Disc
has come to a complete stop.
Plug in the Motor Base. The Control Panel will illuminate.
Place the Work Bowl onto the unplugged Motor Base
and twist clockwise to secure.
3938
3 Carefully remove the Work
Bowl & Processor Base from
the Motor Base. Remove
the Work Bowl Lid from the
Work Bowl, and follow the
disassembly instructions to
remove the Work Bowl from
the Processor Base & Blade
Assembly. Disassembly should
occur in the exact reverse
order of assembly.
WARNING: Use caution when
handling the Blade or Disc.
4 The Blades, Discs, Work
Bowl, and Work Bowl Lid are
top-rack dishwasher-safe.
If using a diswasher, wash the Lid, Blade Assembly,
and Grinding Cup in the top rack only.
WARNING: Do not place
the Processor Base and
Blade Adapter into the
dishwasher. The Processor
Base and Blade Adapter
should be washed by hand.
WARNING: NEVER use the
sanitize or heat cycle when
any nutribullet
®
Ultra Plus+
parts or attachments are in
the dishwasher.
Place the Motor Base and Work Bowl on a flat, clean, and dry surface.
6 To remove stubborn
residue from Discs or Blades,
immerse in room-temperature
water and add 1-2 drops of
dish soap. Wait 20-30 seconds
to loosen debris enough to
scrub away.
5 Alternatively, you can wash
the Processor Attachment
parts by hand using a sponge
or cloth, soap, and water.
WARNING: Blades are sharp,
use extreme caution when
handling and cleaning the
Blade and Disc.
STORAGE:
• Store the Blade and Disc
inside the Work Bowl. Install
the Blade Adapter on the
center shaft of the Work Bowl,
followed by the Chopping
Blade and Slice/Shred Disc.
• When storing the Disc, secure
the Disc in the lower position
of the Blade Adapter located
approximately halfway down
the Blade Adapter shaft. Hold
the center knob of the Disc,
but DO NOT align the marks
on the Disc with the marks on
the Blade Adapter. Lower the
Disc down the shaft until it is
secured in the lower position.
• Attach the Work Bowl Lid
once all components
are in place.
• NEVER store or leave Blades
or Discs exposed. Always
cover or store with the
appropriate lid or cover.
7 Gently wipe the surface
of the Motor Base using a
damp sponge or cloth.
WARNING: NEVER immerse
the Motor Base in water or
other liquid.
Place the Motor Base and Work Bowl on a flat, clean, and dry surface.
Clean the Motor Base with a damp sponge or cloth.
4140
WARNING: KEEP
THESE IMPORTANT
SAFEGUARDS IN MIND
WHEN USING THE ULTRA
PLUS+ COFFEE & SPICE
ATTACHMENT:
Using your nutribullet
®
Ultra Plus+ Coee & Spice
Grinder Attachment.
1 Place the nutribullet
®
Ultra
Plus+ Motor Base on a
clean, dry, and level surface.
Ensure that it is plugged in
and powered on.
2 Open the Grinder by
twisting the Grinding
Cup clockwise.
Open the Grinder by twisiting the Lid Cover clockwise.
Plug in the Motor Base. The Control Panel will illuminate.
• Always check your Coee
& Spice Grinder Attachment
for any foreign objects or
damage before using.
• Do not add liquid ingredients
to the Coee & Spice
Grinder Attachment.
• Do not grind ice with the Coee
& Spice Grinder Attachment.
3 Add ingredients to the
Grinding Cup. DO NOT
exceed the MAX line.
5 Twist the Grinder clockwise
until it locks (“clicks”) into
place. This will illuminate the
Control Panel.
NOTE: The nutribullet
®
Ultra
Plus+ will not operate unless the
attachment is locked in place.
4 Secure the Grinding Cup
onto the Grinder Blade,
then place it onto the
Motor Base.
WARNING: Do not overfill
the Grinder. Overfilling may
prevent the blades from
spinning freely, causing
the Motor Base to overheat
and thereby engaging the
thermal safety breaker. If
the Motor Base comes to
an unprompted stop at any
point, this likely indicates that
the motor has overheated.
Wait for the Motor Base to
cool down (approximately 15
minutes), then resume use.
Add ingredients to the Grinder. DO NOT exceed the MAX line.
Twist the Grinder clockwise until locks into place.
Secure the Lid onto the Grinder, then place it onto the Motor Base.
4342
7 Once the grinding process
has stopped, unlock the
Grinder Attachment by
twisting counter-clockwise.
9 Remove the plug from
the outlet and store your
nutribullet
®
Ultra Plus+ safely,
making sure that the cord
is not left hanging over
the edge of a table or counter,
or touching any hot surfaces.
8 Detach the Grinder
from the Motor Base.
Open the Grinding Cup to
access your ingredients.
6 For best results, grind
ingredients using short 1-to-2
second pulses until reaching
your desired consistency. To
pulse ingredients, press and
hold the Dashed Circle on the
front of the Motor Base for
your desired grinding time.
Release your finger from the
Dashed Circle to stop the
grinding process.
Once the grinding process has stopped, unclock the
Grinder attachment by twisting counter-clockwise.
Once the grinding process has stopped, unclock the
Grinder attachment by twisting counter-clockwise.
Disengage the Grinder attachment from the Motor Base.
Plug in the Motor Base. The Control Panel will illuminate.
Troubleshooting.
PROBLEM:
My nutribullet
®
Ultra Plus+
won’t turn on.
SOLUTIONS:
• Check your outlet. Ensure that
the Motor Base is plugged in
properly and that the Grinder
is locked (“clicked”) into place
on the Motor Base.
PROBLEM:
My nutribullet
®
Ultra Plus+
won’t turn o.
SOLUTIONS:
• Unplug the power cord from
the outlet. Make sure that
the Motor Base is powered
o and that the blades are
completely stopped before
removing the Grinder.
PROBLEM:
The coee/spices are not
evenly ground.
SOLUTIONS:
• Select and hold the Dashed
Circle on the Control Panel
for pulse grinding. Hold the
Dashed Circle icon until your
coee or spices are ground
to satisfaction.
4544
Ultra Plus+ Coee
& Spice Attachment
maintenance & storage.
CLEANING:
WARNING: FOLLOW
THESE IMPORTANT
SAFEGUARDS WHEN
USING THE ULTRA
PLUS+ COFFEE & SPICE
GRINDER ATTACHMENT:
• SHARP BLADES, ALWAYS use
caution when handling or
cleaning the Blades or Discs.
• DO NOT remove any
attachment until the Blades
or Discs have come to a
complete stop.
• NEVER place a partially-
assembled Blade Assembly
onto the Motor Base. Only
place fully-assembled
components on the Motor Base.
• ALWAYS unplug the unit when
not in use, before assembling
or dissembling parts, and
before attempting to clean.
• DO NOT use the Grinder
Attachment as a storage
container.
• ALWAYS clean components
after each use.
44
1 Unplug the Motor Base
from the outlet.
2 Disengage the Grinder
attachment from the
Motor Base.
Plug in the Motor Base. The Control Panel will illuminate.
Disengage the Grinder attachment from the Motor Base.
45
6 Clean the Motor Base with
a damp sponge or cloth.
4 If using a dishwasher, wash
the Grinder Blade and
Grinding Cup in the top
rack only.
WARNING: NEVER wash
Grinder components using
the sanitize or heat cycle
of the dishwasher.
DO NOT immerse the
Motor Base in water or
other liquid.
5 Alternatively, you can wash
the Grinding Cup and
Grinder Blade by hand,
using a sponge or cloth,
soap, and water.
WARNING: Blades are
sharp, use caution when
handling and cleaning the
Blade Assembly.
3 Disassemble the Grinding
Cup and Grinder Blade.
WARNING: Use caution
when handling the Blade.
STORAGE:
• Store your nutribullet
®
Ultra Plus+
blender and Coee & Spice
Grinder Attachment in a dry, cool,
and clean place. Make sure the
power cord is safely tucked away.
WARNING: Never leave an
exposed Blade Assembly in
the Motor Base.
Open the Grinder by twisiting the Lid Cover clockwise.
Alternatively, you can wash the Lid, Blade Assembly,
and Grinding Cup by hand using a sponge or cloth, soap, and water.
If using a diswasher, wash the Lid, Blade Assembly,
and Grinding Cup in the top rack only.
Clean the Motor Base with a damp sponge or cloth.
General care &
maintenance.
WARNING: KEEP
THESE IMPORTANT
SAFEGUARDS IN
MIND WHEN USING
THE NUTRIBULLET
®
:
• Always power o and
unplug your nutribullet
®
Ultra Plus+ when not in
use or when assembling,
disassembling, changing
accessories, or cleaning.
• Always wait until the motor
comes to a complete stop
before removing the Cup,
Attachments, or when
handling the unit.
• Do not place Cups,
Attachments, and To-Go Lids
in the microwave, they are
not microwave safe.
• Do not store an exposed
Rapid Extractor Blade on
the Motor Base without
attaching a Cup.
• NEVER place the Rapid
Extractor Blade, Cups,
Attachments or To-Go Lids
on the bottom rack or use
the heat/sanitize cycle of
your dishwasher when
cleaning. It may cause
warping and possible
safety hazards.
• Do not attempt to clean the
Motor Base by immersing
in water or other cleaning
liquids. Gently wipe and dry
with a clean cloth.
• Do not place any parts or
accessories in a microwave,
conventional oven, air fryer
or stovetop pot, or immerse
in boiling water to clean or
sanitize, as this will damage
the part.
• Make sure that the Motor
Base ventilation areas are
unobstructed and clean.
• Periodically inspect your
nutribullet
®
Ultra Plus+
components for damage or
wear that may impair proper
function or present a danger
or safety hazard. Never
operate your nutribullet
®
Ultra Plus+ with damaged
parts or components:
- Discontinue use if you
detect cracking, cloudiness,
warping, or damage to
the Cups or Processor
Work Bowl.
- Discontinue use if the
Rapid Extractor Blade
does not rotate freely, or
if the gasket is missing or
damaged. Continued use
with a damaged blade, or
use inconsistent with these
instructions may result
in bodily injury, property
damage, or damage to
your unit.
• NEVER attempt to use
your nutribullet
®
Ultra Plus+
if it malfunctions, dropped,
appears to be damaged or
compromised in any manner.
Contact Customer Service
for assistance at:
1 (800) 523-5993.
• Depending on use, it is
recommend that the Rapid
Extractor Blade be replaced
at least every 5 years.
• NEVER use after-market
replacement parts for your
nutribullet
®
Ultra Plus+.
Aftermarket parts are
not made to nutribullet
®
specifications and may
damage your unit or
cause serious injury. Use
only genuine nutribullet
®
attachments/accessories
specifically designed for
your nutribullet
®
Ultra Plus+
blender by calling Customer
Service at: 1 (800) 523-5993.
46 47
4948
nutribullet
®
Ultra Plus+
Compact Kitchen
System one-year
limited warranty.
nutribullet’s limited warranty
obligations are confined to the
terms set forth below:
nutribullet, LLC (“nutribullet”)
warrants this nutribullet
®
against defects in materials
and workmanship for a period
of one year from the date of
original retail purchase or
date of delivery of the product.
This limited warranty is valid
only in the country in which
the product is purchased
and comes with the product
at no extra charge, however
shipping and processing fees
will be incurred for returns,
replacements and or refunds.
If a defect exists, and this
limited warranty is valid, at its
option nutribullet
®
will (1) repair
the product at no charge, using
new or refurbished replacement
parts, (2) exchange the product
with a product that is new or
that has been manufactured
from new or serviceable used
parts and is at least functionally
equivalent to the original
product, or (3) refund the
purchase price of the product.
A replacement product assumes
the remaining warranty of the
original product. A repaired
product has a one-year
warranty from the date of
delivery of the product to the
consumer. When a product
or part is exchanged, any
replacement item becomes
your property and the replaced
item becomes nutribullet’s
property. When a refund is
given, your product becomes
nutribullet’s property.
OBTAINING WARRANTY
SERVICE
For limited warranty service,
simply call our customer
service department at
1 (800) 523-5993 or contact us
via email from our website at
nutribullet.com, simply click
the contact us link, fill out and
submit the customer contact
form and we will be glad to
help you. When you contact our
customer service department
you will be asked for your
name, address, telephone
number and to provide proof of
the original purchase (receipt)
containing a description of
the product(s), purchase
date or date of delivery, and
the appropriate nutribullet
®
serial number(s). Before you
send your product for limited
warranty service please make
sure to keep a copy of all
relevant documents for your
files (receipt, etc.). It is always
recommended to purchase
product insurance and tracking
services when sending your
product for service. Remember,
shipping and processing fees
will be incurred and are not
covered by the one-year
limited warranty.
EXCLUSIONS & LIMITATIONS
This nutribullet
®
One-Year
Limited Warranty applies only to
nutribullet
®
products distributed
by or for nutribullet
®
that can
be identified by the “nutribullet”
trademark, trade name, logo
and bar code. nutribullet’s
One-Year Limited Warranty
does not apply to any other
products that may appear to
be authentic, but were
not distributed/sold by
nutribullet, LLC.
Normal wear and tear is not
covered by this limited warranty.
This limited warranty applies
to consumer use only, and
is void when the product
is used in a commercial or
institutional setting.
This limited warranty
extends only to the original
consumer purchaser and is
not transferable. In addition,
proof of purchase must
be demonstrated.
Repair or replacement of
the product (or, if repair or
replacement is not feasible, a
refund of the purchase price)
is the exclusive remedy of the
consumer under this limited
warranty. nutribullet, LLC shall
not be liable for any incidental
or consequential damages for
breach of this limited warranty
or any implied warranty on
this product.
This limited warranty gives
you specific legal rights, and
you may also have other rights
which vary from state to state.
nutribullet
®
is not liable for
any damage to products not
covered by this warranty (e.g.,
cups, book, User Guide).
This limited warranty does not
apply: (a) to damage caused
by accident, abuse, misuse,
or misapplication; (b) to
damage caused by improper
maintenance (including
unauthorized parts service); (c)
to a product or a part that has
been modified in any way; (d) if
any nutribullet
®
serial number
5150
or trademark has been removed
or defaced; and or (e) if the
product has been used with an
adapter/converter.
THIS LIMITED WARRANTY
AND THE REMEDIES SET
FORTH ABOVE ARE EXCLUSIVE
AND IN LIEU OF ALL OTHER
WARRANTIES, REMEDIES
AND CONDITIONS, WHETHER
ORAL OR WRITTEN, EXPRESS
OR IMPLIED. NUTRIBULLET
®
SPECIFICALLY DISCLAIMS ANY
AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT
LIMITATION, WARRANTIES
OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR
PURPOSE. IF NUTRIBULLET
®
CANNOT LAWFULLY DISCLAIM
IMPLIED WARRANTIES UNDER
THIS LIMITED WARRANTY,
ALL SUCH WARRANTIES,
INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE
ARE LIMITED IN DURATION TO
THE DURATION OF THIS LIMITED
WARRANTY. No nutribullet
®
reseller, agent, or employee
is authorized to make any
modification to this warranty.
NUTRIBULLET
®
IS NOT
RESPONSIBLE FOR DIRECT,
SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES
RESULTING FROM ANY
BREACH OF WARRANTY
OR CONDITION, OR UNDER
ANY OTHER LEGAL THEORY,
INCLUDING BUT NOT LIMITED
TO LOST PROFITS, DOWNTIME,
GOODWILL, DAMAGE TO
OR REPLACEMENT OF
EQUIPMENT AND PROPERTY.
NUTRIBULLET
®
SPECIFICALLY
DOES NOT REPRESENT THAT
IT WILL BE ABLE TO REPAIR
ANY PRODUCT UNDER THIS
LIMITED WARRANTY.
Some states and provinces
do not allow the exclusion
or limitation of incidental or
consequential damages or
exclusions or limitations on the
duration of implied warranties
or conditions, so the above
limitations or exclusions may
not apply to you. This warranty
gives you specific legal rights,
and you may also have other
rights that vary by state
or province.
nutribullet
®
Ultra Plus+
Rapid Extractor Blade
5-year limited warranty.
The Ultra Plus+ Rapid Extractor
Blade that comes with your
nutribullet
®
Ultra Plus+ or
that is purchased separately,
is covered by a five (5) year
limited warranty that applies
to purchases made from
authorized retailers of the
nutribullet
®
products.
nutribullet
®
warrants, subject to
the conditions and exclusions
described herein, that the Ultra
Plus+ Rapid Extractor Blade
shall be free from defects in
material and workmanship
for a period of five (5) years
from the date of original retail
purchase or date of delivery of
the product to the consumer
when it used under normal
household conditions and is
maintained according to the
requirements discussed in the
Owner’s Guide.
What is covered by the
Ultra Plus+ Rapid Extractor
Blade limited warranty?
Your nutribullet
®
Ultra Plus+
Rapid Extractor Blade will be
replaced within five (5) years
from the from the date of
original retail purchase or date
of delivery of the product to the
consumer under the terms of
this limited warranty if:
• The blade breaks due to a
manufacturing defect.
• There is a bearing failure.
• There is a grinding sound
from the blade assembly
when running.
• The blade gasket leaks or
becomes damaged.
• The blade stops rotating.
• The blade threading for
the mixing cup becomes
damaged when used
according to the User Guide.
• The drive coupling loosens or
becomes damaged.
• The plastic blade housing
cracks or breaks when used
according to the User Guide.
• The blade to base
engagement and recognition
system becomes damaged.
5352
Is there a replacement
blade warranty?
In the event a replacement Ultra
Plus+ Rapid Extractor Blade is
issued, the warranty coverage
ends upon the later of six (6)
months following the receipt date
of the replacement Ultra Plus+
Rapid Extractor Blade, OR
the remainder of the existing
5-year limited warranty.
What is not covered by
this warranty?
• Normal wear and tear of
the Ultra Plus+ Rapid
Extractor Blade.
• Any Ultra Plus+ Rapid
Extractor Blade that has been
tampered with or used for
commercial purposes.
• Any Ultra Plus+ Rapid
Extractor Blade that has
been modified.
• Damage caused by misuse,
abuse, negligent handling,
failure to perform required
maintenance or damage due
to any mishandling.
• Damage caused by a failure
to follow the operating
instructions
in the User Guide.
• Consequential and
incidental damages.
• Defects caused by repair
persons not authorized by
nutribullet, including without
limitation, defects include
damages caused in the process
of shipping, altering, or repairing
the Ultra Plus+ Rapid Extractor
Blade when the repair is
performed by a
repair person not authorized by
nutribullet
®
.
• Products purchased, used,
or operated outside of
North America.
• Shipping and handling fees
associated with replacing your
Ultra Plus+ Rapid Extractor Blade
under the terms of this
limited warranty.
• Any Ultra Plus+ Rapid Extractor
Blades with a date code that is
over 6 years old.
• Cosmetic changes to the color
of the plastic blade housing that
does not aect performance,
such as discoloration.
How to initiate a warranty
claim for your Ultra Plus+
Rapid Extractor Blade.
You must call 1 (800) 523-5993
to initiate a warranty claim. You
will need the receipt as proof
of purchase. We also ask to
have the nutribullet
®
Ultra Plus+
base on hand when you call,
so we may better assist you. A
Customer Service Specialist will
review your Ultra Plus+ Rapid
Extractor Blade issue with you
and provide you with further
guidance.
How state law applies.
Some states and provinces do not
allow the exclusion or limitation
of incidental or consequential
damages or exclusions or
limitations on the duration of
implied warranties or conditions,
so the above limitations or
exclusions may not apply to you.
This warranty gives you specific
legal rights, and you may also
have other rights that vary by
state or province.
54
How to find serial number
under the Motor Base.
Please visit nutribullet.com
/register or call
1 (800) 523-5993 to register
your new nutribullet
®
Ultra
Plus+ blender. You will be asked
to enter the Serial Number*
of your product, along with
the purchase date and place
of purchase. The information
you submit is for product
registration. Failure to
complete product registration
does not diminish your
warranty rights.
The registration will enable us
to contact you in the unlikely
event of a product safety
notification. By registering your
product, you acknowledge that
you have read and understood
the instructions for use, and
warnings set forth in the
accompanying instructions.
Product registration.
*
Capital Brands Distribution, LLC | nutribullet.com | All rights reserved.
nutribullet
®
and the nutribullet
®
logo are trademarks of CapBran Holdings, LLC
registered in the U.S.A. and worldwide.
Illustrations may dier from the actual product. We are constantly striving
to improve our products, therefore the specifications contained herein are
subject to change without notice.
NB50550_241126
