Loading ...
Loading ...
Loading ...
8
9
OPERATION
WARNING
To reduce the risk of injury, always
wear proper eye protection marked
to comply with ANSI Z87.1.
Always wear leather gloves over l
atex/rubber
gloves
to avoid entanglement.
Arming the Machine
The MX FUEL™ machines must be armed prior to
use. Even with the battery pack inserted, the trig-
ger and machine functions will not operate until the
machine is armed.
To arm the machine:
1. Insert the battery pack.
2. Press and hold the arm button for about 2 seconds.
The MX FUEL™ icon will light, and the trigger and
LEDs are now operational.
3. After 15 minutes of inactivity, the machine will enter
sleep mode. The MX FUEL™ icon will go off and
the trigger and LEDs are un-operational.
4. Press and hold the arm button for 1 second to
reactivate the machine.
5. Press and hold the arm button for 1 second to
unarm (turn off ) the machine. The MX FUEL™
icon will go off .
Using Forward/OFF/Reverse Switch
Forward OFF Reverse
1. For Forward (clockwise) rotation, move the
Forward/OFF/Reverse switch to the arrow pointing
towards the nose of the drum . Check the
direction of rotation before use. NOTE: Use
Forward to both feed and retract the cable.
2. For Reverse (counterclockwise) rotation, turn
the Forward/OFF/Reverse switch to the arrow
pointing away from the nose of the drum . Check
the direction of rotation before use. NOTE: Only
use Reverse to clear jammed cable. Do not use
Reverse to retract the cable.
3. To turn the rotation OFF and lock the switch, turn
the Forward/OFF/Reverse switch to the center
position O. The foot pedal will not work while the
Forward/OFF/Reverse switch is in the center
locked position. Always lock the switch or remove
the battery pack before performing maintenance,
changing accessories, storing the machine and
any time the machine is not in use.
Starting and Stopping Speed
1. To start the machine, push the Forward/OFF/
Reverse switch to Forward and step or kneel
on the foot pedal.
2. To stop the machine, release pressure on the
pedal. Then, push the Forward/OFF/Reverse
switch to the center position O.
Using the Cable Feed
The cable feed can be used to assist in advancing
and retrieving the cable.
To use the cable feed:
1. Insert the battery pack.
2. Arm the machine.
3. Move the Forward/OFF/Reverse switch to Forward
.
4. Use the foot pedal to start the drum.
5. To engage the cable
feed, press the cable
feed ratchet lever down.
6. To retract the cable,
push the cable feed
handle, as shown. The
further the handle is
pushed, the faster the
cable will retract.
7. To advance the cable,
push the cable feed
handle, as shown. The
further the handle is
pushed, the faster the
cable will advance.
8. To stop the cable from
advancing or retracting,
disengage the cable
feed by pressing the
quick release button.
Move the cable feed
ratchet lever to the
center to slow/stop the
cable.
I
nserting Cable Into Drain
1. Transport and set the machine up according to
these instructions.
2. Ensure the cable feed is disengaged.
3. Grasp the cable close to the machine and feed at
least 2' of cable into the drain by hand. WARNING!
Always wear leather gloves over l
atex/rubber gloves
to avoid entanglement.
4. Move the Forward/OFF/Reverse switch to Forward
and press the foot pedal to begin rotating the
cable.
5. Feed the cable into the drain. Use the cable feed
in "advance" if desired. Continue until the obstruc-
tion is reached.
NOTE: If more cable is needed to reach the clog,
disconnect the original cable from the anchor cable.
Then, either load additional cable into the machine
and connect the two cables together, or connect
the original cable to the cable in another machine.
WARNING! Never feed more than 100' of cable into
the machine to avoid overloading.
6. When the clog is reached, disengage the auto
feed. Manually move the cable in a back and
forth motion until the obstruction is cleared. If the
machine binds, release pressure from the foot
pedal immediately. Repeat until the drain is clear.
To Unbind Cable in the Drain
To relieve torque (twisting) on the cable:
1. Disengage the cable feed.
2. Move the Forward/OFF/Reverse switch to
Reverse and pulse the foot pedal once to begin
rotating the cable. Do not hold down the foot
pedal.
3. Pull the cable back out from the drain a few inches
to free the cable.
4. After the cable is freed from the obstruction and
the machine has come to a complete stop, switch
back to Forward and continue working the ob-
struction.
CAUTION
Running the machine in Reverse for
extended periods can cause damage
to the cable and accessories.
Removing Cable From Drain
1. Move the Forward/OFF/Reverse switch to
Forward and press the foot pedal to begin rotat-
ing the cable.
2. Pull the cable away from the drain and feed it into
the drum. Use the cable feed in "retract" if desired.
3. As the working end of the cable is neared, feed
the last 5' of cable into the machine by hand.
Do not use cable feed. WARNING! Never feed
more than 100' of cable into the machine to avoid
overloading.
4. Remove the drum plug and drain into a suitable
location.
5. Before storing the machine, wash the cable and
drum (see "Cleaning Cables and Drum" in Main-
tenance).
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or machine before
performing any maintenance. Never disassemble
the machine, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Machine
Keep your machine, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your machine for issues such as undue noise,
misalignment or binding of moving parts, breakage
of parts, or any other condition that may aff ect the
machine operation. Return the machine, battery
pack, and charger to a MILWAUKEE service facility
for repair. After six months to one year, depending on
use, return the machine, battery pack and charger to
a MILWAUKEE service facility for inspection.
If the machine does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the machine still does not work
properly, return the machine, charger and battery
pack, to a MILWAUKEE service facility for repairs.
ONE-KEY™
WARNING
Chemical Burn Hazard.
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or en-
tered the body, seek immediate medical attention.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
If the Bluetooth
®
communication stops working,
remove and reinsert the coin cell battery to reset.
Replace the battery if the problem continues.
To replace the battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the battery door.
3. Remove the old battery. Take note of the positive/
negative orientation. WARNING! Keep battery
away from children, and dispose of it properly.
4. Insert the new battery (3V CR2032) in the proper
positive/negative orientation.
5. Close the battery door and tighten the screw(s)
securely.
WARNING
To reduce the risk of personal in-
jury, electric shock and damage,
never immerse your machine in liquid or allow a
liquid to fl ow inside it.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use fl ammable or
combustible solvents around machines.
Greasing the Cable Feed
Apply grease to the cable feed after each use.
1. Unarm the machine.
2. Press the quick release
Zerk Fittings
button.
3. Push the cable feed handle
to the left side of the ma-
chine.
4. Apply MILWAUKEE Grease
Type T (49-08-4290) to
the upper Zerk fi tting, suf-
fi ciently covering the fi tting.
5. Press the cable feed ratchet
lever down.
6. Push the cable feed handle to the right side of
the machine.
7. Apply MILWAUKEE Grease Type T (49-08-4290)
to the two lower Zerk fi ttings, suffi ciently covering
the fi ttings.
Loading ...
Loading ...
Loading ...