BAUMR-AG DRLDPRBMRBD13 420W Benchtop Drill Press User Manual

Video Tutorial:

Drill Press - Assembly

User Manual

[Revision 7.0 December 2023]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND

MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in

appearance, assembly, inclusions, specifications, description, and packaging.

Drill Press – DP13 Series II

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death,

injury or equipment or property damage if not understood or followed. Safety messages have the

following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be INJURED if you

do not follow instructions or

equipment damage may occur.

It is vital that you read and understand

this user manual before using the product,

including safety warnings, and any

assembly and operating instructions.

Keep the manual for future reference.

Safety precautions and recommendations

detailed here must be fully understood

and followed to reduce the risk of injury,

fire, explosion, electrical hazard, and/or

property damage.

Safety information presented here is

generic in nature – some advice may not

be applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered

or combustion engine powered.

• Before Use - If you are not familiar with

the safe operation/handling of the

equipment or are in any way unsure of

any aspect of suitability or correct use

for your application, you should

complete training conducted by a

person or organization qualified in safe

use and operation of this equipment,

including fuel/electrical handling and

safety.

• Do NOT operate the equipment in

flammable or explosive environments,

such as in the presence of flammable

liquids, gases or dust. The equipment

may create sparks or heat that may

ignite flammable substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the

equipment unless they have read this

manual and are adequately trained.

• Keep packaging away from children -

risk of suffocation! Operators must use

the equipment correctly. When using

the equipment, consider conditions and

pay due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting

dust extraction / collection facilities,

ensure these are connected and used

properly. Dust collection can reduce

dust-related hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in

the operating area of the equipment to

help protect from eye and ear injury,

poisoning, burns, cutting and crush

injuries. Protective equipment such as

safety goggles, respirators, non-slip

safety footwear, hard hat, hearing

protection etc should be used for

appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective

equipment. Do not wear loose clothing

or jewellery, which can be caught in

moving parts. Keep hair and clothing

away from the equipment.

• Stay alert and use common sense

when operating the equipment. Do not

over-reach. Always maintain secure

footing and balance.

• Do not use the equipment if tired or

under the influence of drugs, alcohol or

medication.

• This equipment is not intended for use

by persons with reduced physical,

sensory or mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely

flammable – keep clear of naked

flames or other ignition sources.

• Do not spill fuel. If you spill fuel, wipe it

off the equipment immediately – if fuel

gets on your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors

CAN KILL IN MINUTES. Engine

exhaust contains carbon-monoxide – a

poison you cannot smell or see.

• Use combustion engines OUTSIDE

only, and far away from windows, doors

and vents.

General Equipment Use and Care

• The equipment is designed for

domestic use only.

• Handle the equipment safely and

carefully.

• Before use, inspect the equipment for

misalignment or binding of moving

parts, loose components, damage or

any other condition that may affect its

operation. If damaged, have the

equipment repaired by an authorised

service centre or technician before use.

• Prevent unintentional starting of the

equipment - ensure equipment and

power switches are in the OFF position

before connecting or moving

equipment. Do not carry equipment

with hands or fingers touching any

controls. Remove any tools or other

items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be

safer when used within its design and

usage parameters.

• Use the equipment and accessories

etc. in accordance with these

instructions, considering working

conditions and the work to be

performed. Using the equipment for

operations different from those

intended could result in hazardous

situations.

• Always keep equipment components

(engines, hoses, handles, controls,

frames, housings, guards etc) and

accessories (cutting tools, nozzles, bits

etc) properly maintained. Keep the

equipment clean and, where applicable,

properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the

equipment near flammable materials,

combustible gases or liquids etc.

• The equipment is not weather-proof,

and should not be stored in direct

sunlight, at high ambient temperatures

or locations that are damp or humid.

• Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

• For specific equipment safety use and

care, see Equipment Safety.

Drill Press – DP13 Series II

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings

for damage or wear before each use.

Repair or replace damaged equipment

immediately.

• Ensure all power sources conform to

equipment voltage requirements and

are disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and

safety codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating

this item (electrical items only).

• High voltage / high current power lines

may be present. Use extreme caution

to avoid contact or interference with

power lines. Electrical shock can be

fatal.

General Electrical Safety

• Electrically grounded equipment must

have an approved cord and plug and

be connected to a grounded electrical

outlet.

• Do NOT bypass the ON/OFF switch

and operate equipment by connecting

and disconnecting the electrical cord.

• Do NOT use equipment that has

exposed wiring, damaged switches,

covers or guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift,

move or carry equipment.

• Do NOT coil or knot electrical cords,

and ensure electrical cords are not trip

hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres

by qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to

ensure equipment safety is maintained.

• Do NOT attempt any maintenance or

repair work not described in this

manual.

• After use, the equipment and

components may still be hot – allow the

equipment to cool and disconnect spark

plugs and/or electrical power sources

and/or batteries from it before

adjusting, changing accessories or

performing repair or maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service related activities in

suitable conditions, such as a

workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Drill Press Safety

• This drill press is designed for operating under ambient temperatures between +5°C and 40°C and for installation at altitudes no more

than 1000m above M.S.L. The surrounding humidity should less than 50% at 40°C. It can be stored or transported under ambient

temperatures between -25°C and 55°C.

• Recycle unwanted materials instead of disposing of them as waste. All tools, hoses and packaging should be resorted, taken to the

local recycling centre and disposed of in an environmentally safe way.

• Read this manual and labels affixed to the machine to understand its limitations and potential hazards.

• Be thoroughly familiar with the controls and their proper operation. Know how to stop the machine and disengage the controls quickly.

• Do not attempt to operate the machine until you fully understand how to properly operate and maintain the engine and how to avoid

accidental injuries and/or property damage.

• If the unit is to be used by someone other than original purchaser or loaned, rented, or sold, always provide this manual and any

needed safety training before operation. The user can prevent and is responsible for accidents or injuries that may occur to

themselves, other people, and property.

• Do not force the machine. Use the correct machine for your application. The correct machine will do the job more efficiently and safer

at the rate it was designed.

Personal Safety

• Do not permit children to operate this machine at any time.

• Keep children, pets, and other people not using the unit away from the work area. Be alert and shut off unit if anyone enters work

area. Keep children under the watchful care of a responsible adult.

• Do not operate the machine while under the influence of drugs, alcohol, or any medication that could affect your ability to use it

properly.

• Dress properly. Wear heavy long pants, boots, and gloves. Do not wear loose clothing, short pants, or jewellery of any kind. Secure

long hair so it is above shoulder level. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery, or long

hair can be caught in moving parts.

• Protect eyes, face, and head from objects that may be thrown from the unit. Always wear safety goggles or safety glasses with side

shields when operating.

• Wear appropriate hearing protection. Wear respiratory protection to avoid the risk of inhaling harmful dust.

• Always keep hands and feet away from all moving parts during operation. Moving parts can cut or crush body parts.

• Always keep hands and feet away from all pinch points.

• Do not touch parts that might be hot from operation. Allow parts to cool before attempting to maintain, adjust, or service.

• Stay alert, watch what you are doing, and use common sense when operating the machine.

• Do not overreach. Do not operate the machine while barefoot or when wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve your footing on slippery surfaces. Keep proper footing and balance at all

times. This enables better control of the machine in unexpected situations.

Drill Press – DP13 Series II

Inspect Your Machine

• Check your machine before starting it. Keep guards in place and in working order. Make sure all nuts, bolts, etc., are securely

tightened.

• Never operate the machine when it needs repair or is in poor mechanical condition. Replace damaged, missing, or failed parts before

using it. Keep the machine in safe working condition. Regularly check to see that keys and adjusting wrenches are removed from the

machine area before starting it. A wrench or a key that is left attached to a rotating part of the machine may result in personal injury.

Avoid accidental starting. Be sure the motor switch is off before transporting the machine or performing any maintenance or service

on the unit.

• Transporting or performing maintenance or service on a machine with its switch on invites accidents. If the machine should start to

vibrate abnormally, stop the motor and check immediately for the cause. Vibration is generally a warning sign of trouble.

Electric Safety

• Protect yourself from electric shock. Do not plug or unplug the motor while standing in or around damp or wet ground. Do not use the

unit in wet or damp areas or expose it to rain. Prevent body contact with grounded surfaces: pipes, radiators, ranges, and refrigerator

enclosures. Make sure your fingers do not touch the plug’s metal prongs when plugging or unplugging the unit.

• Avoid inadvertent starting. Make sure that the switch is switched off when plugging the plug into an outlet.

• Only use approved and appropriately identified extension cables for use outdoors. Only use cable reels in the unrolled state.

• Do not use the cable for purposes for which it is not intended. Do not use the cable to pull the plug out of the outlet. Protect the cable

from heat, oil and sharp edges.

• Have your electric tool repaired by a qualified electrician. This electric tool conforms to the applicable safety regulations. Repairs may

only be performed by an electrician using original spare parts. Otherwise accidents can occur.

Work Area & Store Area

• Keep the work area orderly. Disorder in the work area can lead to accidents.

• Take environmental influences into account. Do not expose electric tools to rain. Do not use electric tools in a damp or wet

environment. Make sure that the work area is well-illuminated. Do not use electric tools where there is a risk of fire or explosion.

• Securely store unused electric tools. Unused electric tools should be stored in a dry, elevated or closed location out of the reach of

children.

Machine Use and Care

• Never turn the drill press on until the table is clear of all foreign objects (tools, scraps, etc.).

• Always keep hands and fingers away from the drill bit.

• Do not drill materials without a flat surface.

• Never start the drill press with the drill bit pressed against the workpiece.

• Make sure the table lock is tightened before starting the drill press.

• Never layout, assemble, or set-up any work on the table while the drill is on.

• Make sure the drill bit is securely locked in the chuck.

• Make sure the chuck key is removed from the chuck before turning power on.

• Adjust the table or depth stop to avoid drilling into the table.

• Always stop the drill before removing scrap pieces from the table.

• Use clamps or a vise to secure a workpiece to the table. This will prevent the workpiece from rotating with the drill bit.

• Do not wear gloves when operating a drill press.

• Set the drill press to the speed that is appropriate for the material being drilled.

• If any part of the drill press is missing/ damaged or if the electrical components fail to perform properly, shut the power OFF and

unplug the drill press. Replace missing, damaged or failed parts before resuming operation.

• Before leaving the machine, shut the power off, remove the drill bit and clean the table.

• Take care of your tools. Keep cutting tools sharp and clean in order to be able to work better and more safely. Follow the instructions

for lubrication and for tool replacement. Check the connection cable of the electric tool regularly and have it replaced by a recognized

specialist when damaged. Check extension cables regularly and replace them when damaged. Keep the handle dry, clean and free of

oil and grease.

Residual Risks

Despite proper use, additional residual risks cannot be completely ruled out. The following risks may arise due to the nature of the drill

press:

Mechanical hazards related to:

Machine parts or workpieces:

• Shape

• Relative location

• Mass and velocity (kinetic energy of elements in controlled or uncontrolled motion)

• Mechanical strength

• Crushing hazard

• Cutting or severing hazard

• Entanglement hazard

Drill Press – DP13 Series II

• Drawing-in or trapping hazard

Electrical hazards due to:

• Contact of persons with live parts (direct contact)

• Contact of persons with parts which have become live under faulty conditions (indirect contact)

• Electrostatic phenomena

Hazards generated by noise, resulting in:

• Hearing loss (deafness), other physiological disorders (loss of balance, loss of awareness)

• Interference with speech communication, acoustic signals.

Hazards generated by materials and substances (and their constituent elements)

Processed or used by the machinery

• Hazards from contact with or inhalation of harmful fluids and dusts

• Fire hazard

Hazards generated by neglecting ergonomic principles in machinery design related to:

• Unhealthy postures or excessive effort

• Hand-arm or foot-leg anatomy

• Local lighting

• Mental overload and underload, stress

• Human error, human behaviour

• Design, location or identification of manual controls

Combination of hazards

Unexpected start up, unexpected overrun/ overspeed (or any similar malfunction) from:

• Failure/disorder of the control system

• External influences on electrical equipment

• Errors made by the operator (due to mismatch of machinery with human characteristics and abilities)

• Impossibility of stopping the machine in the best possible conditions

• Variations in the rotational speed of tools

• Failure of the power supply

• Failure of the control circuit

• Errors of fitting

• Break-up during operation

• Falling or ejected objects or fluids

• Loss of stability / overturning of machinery

Drill Press – DP13 Series II

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols

on your product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and

open flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc

before using the product.

Use Hand Protection

Wear appropriate hand

protection and take due care

as the product or use of the

product may present hand

hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Electrocution / Electrical

Shock Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling

electrical products, cables,

plugs and leads. Electrical

shock can be fatal.

Toxic Fumes / Dust Hazard

Using the product or by-

products from use may

produce fumes, smoke or

particles that could be harmful

if inhaled. Wear appropriate

breathing protection and have

adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be

present. Avoid ignition sources

and open flames. Danger of

explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices

that can cause severe cut

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Crush Hazard

The product may have blades,

edges or mechanical devices

that can cause severe crush

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Single Operator Only

The product must be operated

by a single person only. More

than one person operating the

product may introduce

additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care

as the product or use of the

product may present face and

eye hazards.

Use Foot Protection

Wear appropriate foot

protection and take due care

as the product or use of the

product may present foot

hazards.

Use Eye / Ear / Head

Protection

Wear appropriate eye and / or

ear and / or head protection

and take due care as the

product or use of the product

may present eye, hearing and

head hazards.

Running Hazard

Do not run on or near the

product as doing so may

present a fall hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or

objects that can cause severe

injury to fingers, limbs, blood

etc. Take due care when

handling and using the

product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures

and hot surfaces that can

cause burn injuries.

Flying Debris Hazard

Be aware that the product or

use of the product may

present hazards produced by

flying debris. Wear appropriate

clothing and protective

devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts

to stop fully before handling

the product, adjusting,

maintenance etc.

Drill Press – DP13 Series II

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due

care when handling and using

the product.

Slope / Fall Injury Hazard

Be aware that using the

product on sloping surfaces or

in slippery conditions may

present additional dangers

from falls and contact with

blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result

in severe injury due to falling,

product breakage or collapse

etc.

Electrocution / Electrical

Shock Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do

NOT use in rain, damp or wet

conditions. Electrical shock

can be fatal.

Electrocution / Electrical

Shock Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product.

Always disconnect the product

from the electrical supply

before handling the product,

adjusting, maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current

power lines may be present.

Use extreme caution to avoid

contact or interference with

power lines. Electrical shock

can be fatal.

"Kick-Back" Hazard

High level of "kick-back"

hazard that can cause the

machine to suddenly rotate

towards operator. Kick-back

injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch

to move people.

Winch Lift Hazard

Do NOT LIFT load vertically.

Use machine to PULL only.

Cable Hazard

Ensure that load bearing cable

is not kinked or knotted.

Winch Cable Hazard

Ensure that there is a

minimum number of cable

coils on winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye

protection for welding. Direct

exposure to weld arcs may

cause permanent eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Drill Press – DP13 Series II

Table of Contents

Safety ................................................................................................................................................ 2

Safety Symbols ............................................................................................................................................ 6

Parts Identification ........................................................................................................................... 9

Know your Machine ....................................................................................................................... 10

Assembly ........................................................................................................................................ 11

Column Tube .............................................................................................................................................. 11

Drilling Bench ............................................................................................................................................. 12

Machine Head ............................................................................................................................................ 13

Drill Chuck Guard ....................................................................................................................................... 14

Drill Chuck .................................................................................................................................................. 15

Drill Lifting Arms ......................................................................................................................................... 16

Drill Chuck Key ........................................................................................................................................... 17

Depth Stop ................................................................................................................................................. 18

Set-Up ............................................................................................................................................. 19

Selecting the Speed ................................................................................................................................... 19

Recommended Spindle Speeds ................................................................................................................ 21

Tensioning the V-belts ............................................................................................................................... 22

Adjusting the Drilling Bench ....................................................................................................................... 23

Changing the Drill Bit ................................................................................................................................. 25

Operation ........................................................................................................................................ 26

Drilling ........................................................................................................................................................ 26

General Drilling Guidelines - Drilling A Hole .............................................................................................. 26

Drilling Metal............................................................................................................................................... 27

Drilling Wood .............................................................................................................................................. 27

Transport, Maintenance and Storage ........................................................................................... 28

Transport .................................................................................................................................................... 28

Maintenance ............................................................................................................................................... 28

Servicing .............................................................................................................................................. 28

Cleaning ............................................................................................................................................... 28

Storage ....................................................................................................................................................... 29

Troubleshooting ............................................................................................................................. 30

Specifications ................................................................................................................................. 32

Drill Press – DP13 Series II

Parts Identification

The drill press comes partially assembled and is shipped in carefully packed carton.

After all the parts have been removed from the carton, you should have:

No. Name No. Name

1 Machine Head 15 Hardware Bag including:

2 Column Tube

3

Drilling Bench

4

Drill Chuck

5

Drill Chuck Guard

6

Baseplate

7 Drill Chuck Key

10 Depth Stop

11

Drill lifting arm (x3)

12

Allen Key, 5mm

13

Allen Key, 4mm

14 Allen Key, 3mm

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Know your Machine

Spare parts available

for purchase, scan QR

code below:

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Assembly

This drill press was partially assembled at the factory. To assemble your machine, follow

the below instructions.

Column Tube

Place the column tube on the baseplate. Bolt the column tube to the baseplate with the three screws

M8×20 supplied. Tighten the screws moderately tight with an open-end wrench SW 13 (not scope of

delivery) so that the threads in the baseplate do not strip.

Video Tutorial:

Drill Press - Assembly

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Drilling Bench

Place the drilling bench holder on the column tube. Push the drilling bench holder into a lower position.

Fix the drilling bench holder with the locking handle in the required position.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Machine Head

Place the machine head on the column tube and secure the machine head with the two grub screws to

the side with the allen key 4 mm.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Drill Chuck Guard

Put the drill chuck guard on the upper part of the drill spindle. Secure the drill chuck guard with a

screwdriver (not scope of delivery).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Drill Chuck

Fold the drill chuck guard upwards. Insert the drill chuck on the taper of the drill spindle. Push the drill

chuck onto the drill spindle with a few light taps. Use a plastic hammer for this purpose.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Drill Lifting Arms

Bolt the three drill lifting arms into the hand spindle guide. Tighten the three-hole lifting arms with an

open-end wrench SW 6 (not scope of delivery).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Drill Chuck Key

Attach the drill chuck key into the key holder.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Depth Stop

1. Remove the washer and nut from the depth stop. See below illustration 1.

2. Insert the depth stop through the hole in the fence. See below illustration 2.

3. Screw the depth stop with washer and nut that just had been removed from step 1. Centrally align

the depth stop into the bore of the fence. See below illustration 3.

4. The home position of pointer should be 0mm. See below illustration 4.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Set-Up

Place the drill press on a solid flat surface. Ideally, bolt the drill press to the surface. Use

the two holes in the baseplate for this.

Selecting the Speed

1. Release the locking screw on the gear cover with the allen key 5 mm.

2. Pull the locking screw and open the gear cover.

3. Unfasten the thin nut M8 enough and release the clamping screw with an allen key 6 mm (not

scope of delivery) on the motor. See below illustration 1.

4. Slide the motor forward a little to release the load on the V-belts. See below illustration 2.

5. Remove the V-belt between idle pulley and motor pulley first, then slide idle pulley towards the

spindle pulley to release the load on the V-belt between idle pulley and spindle pulley. Remove the

second V-belt. See below illustration 2 & 3.

6. Place the two V-belts on the desired assembly to reach the specified speed.

7. Slide the motor back to tension the V-belts again. The V-belts are correctly tensioned when it gives

way slightly when pressed. Deflection distance of belt is 5-10mm.

8. Tighten the clamping screw with an allen key 6 mm (not scope of delivery) on the motor again.

9. Close the gear cover. Fasten the locking screw on the gear cover with the allen key 5 mm.

The gear cover is equipped with an interlock switch. If the gear cover is not closed

correctly, the device cannot be switched on.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Recommended Spindle Speeds

Recommended speeds for different drill sizes and materials:

Connection Min

-1

[mm] [mm]

D-4 / 2-I 250 < 3 < 4

D-4 / 3-II 2000 3 – 4 4 – 5

C-3 / 2-I 1850 4 – 5 5 – 6

B-2 / 3-I 1400 5 – 6 6 – 7

C-3 / 4-III 1200 6 – 7 7 – 8

B-2 / 4-III 1000 7 – 8 8 – 9

A-1 / 2-I 800 8 – 9 9 – 10

A-1 / 3-II 650 9 – 10 10 – 11

A-1 / 4-III 500 > 10 > 11

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Tensioning the V-belts

1. Release the locking screw on the gear cover.

2. Open the gear cover.

3. Release the clamping screw on the motor with an allen key 6 mm (not scope of delivery)

4. Slide the motor back to tension the V-belts.

5. The V-belts are correctly tensioned when it gives way lightly when pressed. Deflection distance of

belt is 5-10mm.

6. Tighten the clamping screw on the motor again.

7. Close the gear cover. Fasten the locking screw on the gear cover with allen key 5mm.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Adjusting the Drilling Bench

1. Release the locking handle.

2. Push the drilling bench to the desired height.

3. Pivot the drilling bench to the desired position.

4. Fasten the drilling bench again with the locking handle.

5. You can also adjust the tilt angle of the drilling bench. To do this, release the retaining screw under

the drilling bench with an open-end wrench SW 19 (not scope of delivery). Tilt the drilling bench as

desired to the right or left up to a max. of 45° and secure the drilling bench again with the retaining

screw.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Changing the Drill Bit

Remove the plug from the mains socket before changing the bit. This will prevent an accidental start-

up.

1. Fold the drill chuck guard up.

2. Release the retaining jaws of the drill chuck with the drill chuck key.

3. Remove the bit.

4. Insert a new bit.

5. Tighten the retaining jaws of the drill chuck with the drill chuck key.

6. Check that the bit is centred.

7. Fold the drill chuck guard down again.

8. Attach the drill chunk key back to the key holder.

Under no circumstances must you leave the drill chuck key inserted.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Operation

Always place a piece of backup material (wood, plywood, etc.) on the table

underneath the workpiece. This will prevent splintering on the underside of the

workpiece as the drill bit breaks through. To keep the material from spinning out of control, it

must contact the left side of the column, or be clamped (not included) to the table. For small

workpieces that cannot be clamped to the table, use a drill press vise (not included). The vise

must be clamped or bolted to the table to avoid injury.

Drilling

1. Starting the drill press.

− The drill press can be switched on by pressing the green ON switch ''I''.

− The red OFF switch ''O'' has to be pressed to switch off the drill press.

2. Turn one of the drill’s lifting arms anticlockwise.

3. The drill chuck is lowered.

4. Drill into the workpiece at the appropriate feed rate and to the desired depth.

5. Be aware of any necessary chip breaking on the way to the desired depth.

6. Move the bit slowly back to the stop position.

General Drilling Guidelines - Drilling A Hole

WARNING: To prevent the workpiece and the backup material from slipping from

your hand while drilling, position the workpiece and backup material to the left

side of the column. If the workpiece and the backup material are not long enough to reach the

column, clamp the workpiece and backup material to the table. Failure to do this could result in

personal injury.

1. Mark where you want to drill the workpiece by using a center punch or a sharp nail.

2. Before turning the drill press ON, turn the drilling lifting arms to bring the drill bit down. Line the drill

bit tip up with the mark. Clamp the workpiece in place.

3. Turn ON the drill press and pull down on the drilling lifting arms with the appropriate force needed to

allow the drill bit to drill the material.

Feeding too slowly might cause the drill bit to turn in the chuck. Feeding too rapidly

might stop the motor, cause the belt to slip, force the workpiece loose, or break the drill

bit. Practice with scrap material to get the feel of the machine before attempting to do any

drilling operation.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Drilling Metal

•

Use metal-piercing twist drill bits.

•

It is always necessary to lubricate the tip of the drill with oil to prevent overheating of the drill bit.

All metal workpieces should be clamped down securely. Any tilting, twisting, or shifting causes a

rough drill hole, and increases the potential of drill bit breakage.

•

Never hold a metal workpiece with your bare hands. The cutting edge of the drill bit may seize the

workpiece and throw it, causing serious injury. The drill bit will break if the metal piece suddenly hits

the column.

•

If the metal is flat, clamp a piece of wood under it to prevent turning. If it cannot be laid flat on the

table, then it should be blocked and clamped.

Drilling Wood

•

Brad point bits are preferred. Metal piercing twist bits may be used on wood.

•

Do not use auger bits. Auger bits turn so rapidly that they can lift the workpiece off of the table and

whirl it around.

•

Always protect the drill bit by positioning the table so that the drill bit will enter the center hole when

drilling through the workpiece.

•

To prevent splintering, feed the drill bit slowly right as the bit is about to cut through to the backside

of the workpiece.

•

To reduce splintering and protect the point of the bit, use scrap wood as a backing or a base block

under the workpiece.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Transport, Maintenance and Storage

Transport

•

Unplug the machine from the mains during transport.

•

The machine must only be lifted and transported on its belt housing. Never lift the machine at the

safety devices, the adjusting levers, or the drill chuck.

Maintenance

WARNING: For your safety, turn the switch off and remove the plug from the

power supply. Wait until the rotating tool stands still. All protection and safety

devices must be immediately re-installed once the repair and maintenance work is completed.

CAUTION: All servicing of the drill press should be performed by a qualified service technician.

Servicing

•

Pull the mains plug before any adjustments, maintenance or repair.

•

Have any work on the device that is not described in this instruction guide performed by a

professional. Only use original parts. Allow the device to cool off before any maintenance or

cleaning is undertaken.

•

There is a risk of burning!

•

Always check the device before using it for obvious defects such as loose, worn or damaged parts,

correct the positioning of screws or other parts. Exchange the damaged parts.

•

The ball bearings in the spindle and the V-belt pulley assembly are greased and permanently

sealed. Pull the spindle down and oil the spindle sleeve moderately every three months.

•

Lubricate the table bracket and locking knobs if they become difficult to use.

Cleaning

Do not use any cleaning agents or solvents. Chemical substances can etch the plastic parts of the

device. Never clean the device under running water.

•

Thoroughly clean the device after every use.

•

Clean the ventilation openings and the surface of the device with a soft brush or cloth.

•

Remove chips, dust and dirt with a vacuum cleaner if necessary.

•

Lubricate moving parts regularly.

•

Vacuum sawdust or metal shavings that accumulate in and on the motor, pulley housing, table, and

work surface.

•

Apply a light coat of paste wax to the column and table to help keep these surfaces clean and rust-

free.

•

Do not allow lubricants to come into contact with switches, V-belts, pulleys and drill lifting arms.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Storage

DANGER! Store the drill press a way it cannot be started by unauthorised

persons and that nobody can be injured.

CAUTION! Do not store the drill press unprotected outdoors or in a moist environment.

•

Store the device and its accessories in a dark, dry and frost-proof place that is inaccessible to

children. The optimum storage temperature is between 5 and 30˚C.

•

Store the electrical tool in its original packaging.

•

Cover the electrical tool in order to protect it from dust and moisture.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Troubleshooting

Problem Cause Remedy

Device doesn’t start.



No mains voltage. Main circuit

breaker is tripped.



On switch (green) / Off. Switch

(red) (1) is broken.



Motor faulty.



Check the socket, mains supply cable,

cord, mains plug; if necessary, have

them repaired the main fuse.



Repair by Customer Care.



Repair by Customer Care.

No Motor output turns off

automatically



Motor not fixed in place.



Bit not centrally clamped.



Check the tension of the V-belts and

tighten the clamping screw.



Check the bit in the drill chuck.

Loud squeaking noise.



Incorrect belt tension



Dry spindle



Loosed spindle pulley



Loosed motor pulley



Adjust the belt tension



Lubricate the spindle



Tighten the retaining nut on the pulley

insert



Tighten the set screw on the side of the

motor pulley

The drill bit burns or

smokes



Drilling at the incorrect speed



The wood chips are not coming

out of the hole



Dull drill bit



Feeding the workpiece too

slowly



Not lubricated



Change the speed



Retract the drill bit frequently to clear

the chips



Resharpen or replace the drill bit



Feed fast enough to cut the workpiece



Lubricate the drill bit with cutting oil

Excessive drill run out or

wobble; drilled hole is

not round



Bent drill bit



Bit improperly installed in the

chuck



Worn spindle bearings



Lengths of cutting flutes or

angles not appropriate for the

hardness of the wood grain



Chuck not properly installed



Replace the drill bit



Reinstall the bit.



Replace the bearing. Take the press to

a qualified service technician



Resharpen the drill bit correctly or

replace with the appropriate type.



Reinstall the chuck.

Drill bit binds in the

workpiece



The workpiece is pinching the

bit



Excessive feed pressure



Support or clamp the workpiece.



Feed more slowly.

Spindle returns too

slowly or too quickly



Coil spring has improper tension



Adjust the coil spring tension

Chuck falls off spindle



Dirt, grease, or oil on the

tapered surface on the spindle

or in the chuck



Clean the tapered surface of both the

chuck and spindle with a household

detergent.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Problem Cause Remedy

Motor will not run



Defective or broken switch



Defective or damaged power

cord



Open circuit, loose connections,

or burned out motor



Low voltage



Take to a qualified service technician



Take to a qualified service technician



Take to a qualified service technician



Check the power line for the proper

voltage. Use another circuit or have



a qualified

Motor stalls



Short circuit in motor



Incorrect fuses or circuit

breakers



Overloaded circuit



Low Voltage



Take to a qualified service technician



Replace with correct fuse or circuit

breaker for the circuit



Turn off other machines and retry



Check the power line for the proper

voltage. Use another circuit or have a

qualified electrician upgrade the

service.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Drill Press – DP13 Series II

Specifications

Motor

420W

Chuck

13mm Stainless Steel

Variable Speeds

500 / 650 / 800 / 1000 / 1200 /

1400 / 1850 / 2000 / 2500 RPM

Drill Travel

50mm

Spindle Feed

Rack and Pinion

Spindle to Table

220mm

Spindle to Base

302mm

Table Tilt

±45°

Base

Cast Iron

Switches

Dust Protected NVR

Note: Minimal Assembly required

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG DRLDPRBMRBD13 420W Benchtop Drill Press

Product's Documents

Product manual

Specifications

BAUMR-AG DRLDPRBMRBD13 Questions and Answers