Loading ...
Loading ...
Loading ...
14
14. Tighten the four screws (E
3
).
Figure 5-20
5.16.3 Cursor alignment
3. With fence against blade, verify that cursor (F,
Figure 5-20) aligns with zero on scale.
4. If adjustment is needed, loosen the four screws
(E
3
, Figure 5-19) on the fence body and nudge
fence body left or right along the tracks in the
fence guide, until cursor aligns with zero when
fence is against blade.
5. Tighten the four screws (E
3
).
5.17 Dust collection
It is strongly recommended that a dust collection
system (not provided) be connected to the two 4-
inch diameter ports on the saw. It will help keep the
shop clean, as well as prevent potential health
hazards due to air-borne wood dust. See our
website for a full line of dust collectors.
6.0 Electrical connections
Electrical connections must be
made by a qualified electrician in compliance
with all relevant codes. This machine must be
properly grounded to help prevent electrical
shock and possible fatal injury.
6.1 GROUNDING INSTRUCTIONS
1. All Grounded, Cord-connected Tools:
This machine must be grounded. In the event of a
malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with
an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface
that is green with or without yellow stripes is the
equipment-grounding conductor. If repair or
replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding
conductor to a live terminal.
Before connecting to power source, be sure the
switch is in off position.
Check with a qualified
electrician or service personnel if the grounding
instructions are not completely understood, or if
in doubt as to whether the tool is properly
grounded. Failure to comply may cause serious
or fatal injury.
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug.
Repair or replace damaged or worn cord
immediately.
2. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating less than
150 volts:
This tool is intended for use on a nominal 115-V
circuit, and has a grounded plug that looks like the
plug illustrated in sketch A in Figure 6-1. A
temporary adaptor that looks like the adaptor
illustrated in sketches B and C may be used to
connect this plug to a 2-pole receptacle as shown in
sketch B if a properly grounded outlet is not
available. The temporary adaptor should be used
only until a properly grounded outlet can be installed
by a qualified electrician. The green colored rigid
ear, lug, or the like extending from the adaptor must
be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the
adaptor is used, it must be held in place by a metal
screw.
In Canada, the use of a temporary adaptor is not
permitted by the Canadian Electrical Code, C22.1.
3. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating between
150 - 250 volts, inclusive:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in D, Figure
6-1. The tool is intended to be used with a grounding
plug that looks like the plug illustrated in D. Make
sure the tool is connected to an outlet having the
same configuration as the plug. No adapter is
available or should be used with this tool. If the tool
must be reconnected for use on a different type of
electric circuit, the reconnection should be made by
qualified service personnel; and after reconnection,
the tool should comply with all local codes and
ordinances.
Loading ...
Loading ...
Loading ...