Loading ...
Loading ...
Loading ...
rare cases, there may be a need to generate a new
signal, for instance if two adjacent installations have a
very similar signal.
1. Place the product in the charging station.
2. Do steps 1–3 in
To get access to the menu in the
display of the product on page 22
.
3. Use the arrow buttons and the OK button to move
through the menu structure
Security > Advanced >
New loop signal
.
4. Await confirmation that the loop signal has been
generated. This normally takes about 10 seconds.
4.2.5.3 To change the PIN-code
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 22
.
2. Use the arrow buttons and the OK button to move
through the menu structure
Settings > Security >
Advanced > Change PIN-code
.
3. Enter the new PIN code.
4. Push the OK button.
5. Enter the new PIN code again.
6. Push the OK button.
7. Make a note of the new PIN code. Refer to
Introduction on page 6
.
4.2.5.4 To change the duration of the alarm
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 22
.
2. Use the arrow buttons and the OK button to move
through the menu structure
Security > Advanced >
Duration > Duration of alarm
.
3. Use the arrow buttons to select a time interval of 1
to 20 minutes.
4. Push the BACK button.
4.2.6 Messages
In this menu the previous fault and information
messages can be found. For some of the messages,
there are tips and advice to help to rectify the fault.
Refer to
Troubleshooting on page 36
.
If the product is disrupted in any way, for example it
is trapped or the battery is low, a message is saved
relating to the disruption and the time it happened.
If the same message is repeated several times, this
may indicate that an adjustment to the installation or the
product is required. Refer to
Installation on page 13
.
4.2.6.1 To read the messages
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 22
.
2. Use the
arrow buttons and the OK button to move
through the menu structure
Messages > Fault
messages
and
Messages > Info messages
.
3. Read the messages and read the
Troubleshooting
to get information and recommendations to correct
the faults.
4.2.7 Weather timer
Weather timer
automatically adjust the cutting time to
the growth of the grass. The product is not permitted to
operate more than the schedule settings.
Note: When using
Weather timer
, it is recommended
to make as much operating time as possible available
for
Weather timer
. Do not restrict the schedule more
than necessary.
The first operation of the day is set by the schedule
settings. The product always complete 1 mowing cycle,
and then
Weather timer
selects if the product will
continue to operate or not.
Note:
Weather timer
is reset if the product does not
operate for more than 50 hours, or if a
Reset of all user
settings
is done.
Weather timer
is not changed if a
Reset
of schedule settings
is done.
4.2.7.1 To set the Weather timer
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 22
.
2. Use the arrow buttons and the OK button to move
through the menu structure
Weather timer > Use
Weather timer
.
3. Push the OK button to select the
Weather timer
.
4. Push the BACK button.
4.2.7.2 To set the Weather timer frequency
Set how frequently the product cuts the grass when the
Weather timer
is in use. There are 3 frequency levels:
Low, Mid
and
High
. The higher the frequency, the more
sensitive the product is to the grass growth. That is, if
the grass growth is high then the product is allowed to
work longer.
Note:
If the mowing results are not optimal when
using
Weather timer
, the schedule settings may need
adjusting. Do not restrict the schedule more than
necessary. Also, check that the blade disc is clean and
that the blades are in good condition.
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 22
.
24
- Product settings 1650 - 006 - 20.02.2023
Loading ...
Loading ...
Loading ...