Bosch 06016A00F0 GKF 550 Palm Router (550W)

User Manual - Page 8

For 06016A00F0.

PDF File Manual, 58 pages, Read Online | Download pdf file

06016A00F0 photo
Loading ...
Loading ...
Loading ...
8 | English
(23)
Guide roller
A)
(24)
Handle (insulated gripping surface)
A)
Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Edge router GKF 550
Article number
3 601 FA0 0..
Rated power input W 550
No-load speed min
-1
33,000
Tool holder mm
inches
6
¼
Weight according to
EPTA-Procedure01:2014
kg 1.4
Protection class
/ II
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Fitting
u Pull the plug out of the socket before carrying out any
work on the power tool.
Changing the tool
u Wearing protective gloves while fitting and changing
router bits is recommended.
Original router bits from the extensive range of Bosch ac-
cessories are available from your specialist dealer.
Removing the routing base (see figure A)
Before fitting a router bit, you must first separate the routing
base(2) from the drive unit(1).
Open the wing bolt (10) on the routing base (2).
Pull the drive unit out in an upward direction.
Changing the Collet (seefigureB)
Depending on the router bit used, you may have to change
the cap nut with the collet(7) before fitting the router bit.
If the right collet for your router bit is already fitted, please
follow the work steps in the following section.
The collet(13) must sit in the cap nut with a small amount of
play. The cap nut(7) must be easy to fit. If the cap nut or col-
let is damaged, replace it immediately.
Place the open-ended spanner(15) on the tool holder(14)
(seefigureC1).
Unscrew the cap nut(7) anticlockwise using the open-ended
spanner(16).
If required, clean all the parts you want to fit with a soft
brush or by blowing them clean with compressed air before
assembling them.
Place the new cap nut on the tool holder(14).
Loosely tighten the cap nut.
u Do not, under any circumstances, tighten the collet
with the tightening nut until a router bit has been fit-
ted. The collet may otherwise become damaged.
Fitting the router bit (see figure C1 – C2)
Router bits are available in a wide variety of designs and
qualities depending on the intended application.
Router bits made of high-performance high-speed steel
(HSS) are suited to machining soft materials such as soft-
wood and plastic.
Router bits with carbide tips (HM) are especially suitable
for hard and abrasive materials such as hardwood and alu-
minium.
Original router bits from the extensive range of Bosch ac-
cessories are available from your specialist dealer.
Only use undamaged and clean router bits.
Fitting the routing base (see figure A)
To start routing, the routing base(2) must be fitted back
onto the drive unit(1).
Open the wing bolt(10) on the routing base(2).
Slide the drive unit(1) into the routing base(2).
Close the wing bolt(10) on the routing base(2).
u After assembly, always check that the drive unit is
firmly seated in the routing base.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
Provide for good ventilation of the working place.
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
u Avoid dust accumulation at the workplace. Dust can
easily ignite.
Operation
u Products that are only sold in AUS and NZ: Use a resid-
ual current device (RCD) with a nominal residual current
of 30 mA or less.
u Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230V can also be operated with 220V.
Setting the routing depth
u The routing depth must only be set while the power
tool is switched off.
1 609 92A 5JG | (14.01.2020) Bosch Power Tools
Loading ...
Loading ...
Loading ...