ELECTRIC MINI HOIST
USER MANUAL
Congratulations for your excellent choice our new electric tool is manufactured in
compliance with the best and relibility standards,ensuring you efficiency and safety
for a long period of time
Specific
ation
Method of
use
Rated
Vol(V)
Input
Power
(W)
Rated lifting
weight
(kg)
Lifting
Speed
(m/min)
Lifting
Height
(m)
Quan
/CNT
(PCS)
Packing
Dimension
(cm)
G.W/
N.W
(kg)
PA200
Single-hook
110/220
480
100
10
12
1
38*14*22
11/12
Double-hook
200
5
6
PA250
Single-hook
110/220
510
125
10
12
1
38*14*22
11/12
Double-hook
250
5
6
PA300
Single-hook
110/220
600
150
10
12
1
38*14*22
11/12
Double-hook
300
5
6
PA400
Single-hook
110/220
850
200
10
12
1
44*15*24
15/16
Double-hook
400
5
6
PA500
Single-hook
110/220
1020
250
10
12
1
44*15*24
15/16
Double-hook
500
5
6
PA600
Single-hook
110/220
1150
300
10
12
1
44*15*24
16/17
Double-hook
600
5
6
PA800
Single-hook
110/220
1450
400
10
12
1
44*15*24
19/20
Double-hook
800
5
6
PA1000
Single-hook
110/220
1800
500
10
12
1
59*24*31
30/31
Double-hook
1000
5
6
PA1200
Single-hook
110/220
2050
600
10
12
1
59*24*31
31/32
Double-hook
1200
5
6
GENERAL SAFETY RULES
WARNING! Before using this electric tool. Carefully read the general safety
rules listed below.
1 Your sockets must comply with safety rules. In case your sockets are not
suitable, they should be checked by a skilled electrician.
2 Your socket plug must absolutely be grounded and your electric system
must be supplied with a magneto cut-out safety.
-When the machine is running unwatched, be careful that children cannot
reach it.
-Do not pull the electric cable to disconnect the plug.
-The machine shall be protected from frost and low temperatures.
3 In case the machine cannot hoist a load, do not keep pressing the hoisting
push button: this means that the load exceeds the machine's maximum
capacity.
-The machine shall not be disassembled when running or connected to power.
-Do not stand under hoisted weights.
4 Before starting the work, make sure that the steel cable is correctly winded
around the reel and the pitch is equal to the cable diameter.
5 Observe the maximum load indicated on the hoist, not that no the hook!
6 Leave at least three turns of cable around the reel so that the cable
connection is not under stress.
-To avoid any danger, do not wind more than 15m of cable around the reel.
7 In case the steel cable is worn out, it must be replaced only with a cable of
the same features manufactured by us. It can be found at all authorized service
shops.
-Before starting the word, check that switches are in good operating conditions.
8 In case the hoist stops during the lowering of a load, it is normal that the
load goes down a few centimeters more because of inertia.
9 Attention! The hoist electric motor is not supplied with any overload cut-
out(to avoid an unexpected and unwanted restart) therefore, if you are unable
to hoist a load do not insist and let the motor cool down.
MAINTENACE
-Periodically CHECK that the steel cable is in good condition.
1 CHECK that the screws securing the brackets and reduction gear are
well tightened.
2 CHECK THE CONDITIONS AND TIGHTENING OF THE NUTS
securing the steel cable clamps.
3 Periodically CHECK that the motor stop switch and push button
switch are in good operating conditions.
