1. Home
  2. Dewalt
  3. Dewalt DWOAS5BC User Manual
  4. Page 10

Dewalt DWOAS5BC Brush Cutter Attachment

Instruction Manual - Page 10

For DWOAS5BC.

PDF File Manual, 28 pages, Read Online | Download pdf file

DWOAS5BC photo
Loading ...
Loading ...
Loading ...
ENGLISH
8
Replacing the Cutting Blade (Fig.A, D, E)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, or prior to
cleaning. An accidental start‑up can causeinjury.
When replacing the blade, use 8" (203mm) diameter
blades. Use
DeWALT replacement blade. Other sizes may
degrade performance or cause damage to thebrush
cutterattachment. DO NOT use toothed blades, such as saw
blades, with thisproduct.
1. Removebattery.
2. Remove brush cutter attachment from thepowerhead.
Reverse the steps under Assembling the Brush Cutter
Attachment to thePowerhead.
WARNING: Use gloves and proper eye protection. Turn
the brush cutter on its side. Be careful of sharp edges
ofblade.
Removing the Cutting Blade
1. Align the shaft bushing hole
19
with the locking rod
slot
20
and insert a screwdriver (not supplied) into the
bushinghole. Hold the screwdriver inposition.
Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact
DeWALT call 1‑800‑4‑DeWALT (1-800-433-9258) or
visit our website: www.dewalt.com.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1approved eye
protection when performingthisprocedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Your D
eWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
Brush Cutting (Fig.G, H)
With the brush cutter on, angle it and swing side to side as
shown in Fig.G.
Maintain a minimum distance of 24" (610mm) between the
guard and your feet as shown in Fig.H.
WARNING: Keep the rotating blade roughly parallel
with the ground (tilted no more than 30°). This trimmer
is not an edger. DO NOT TILT the brush cutter so that
the blade is spinning near a right angle to the ground.
Flying debris can cause seriousinjury.
Helpful Cutting Tips
• Use the tip of the blade to do the cutting; do not force
tool head into uncutgrass.
• Wire and picket fences cause extra blade wear, even
breakage. Stone and brick walls, curbs, and wood may
wear stringrapidly.
• In long growth, cut from the top down and do not
exceed 12" (305mm)high.
• Keep brush cutter head tilted toward the area being cut;
this is the best cuttingarea.
• The brush cutter cuts best when passing the unit
from the left to right. This will avoid throwing debris at
theoperator.
• Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by theblade.
WARNING: Hold the tool using only the designated
gripping surfaces: The powerhead handle and the
auxiliary handle.
WARNING: Do not use the pole as a grippingsurface.
Proper hand position requires one hand on the powerhead
handle
16
and one hand on the auxiliary handle
17
.
Proper Hand Position (Fig.F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
WARNING: Use of a shoulder strap
13
is required
while using thistool.
Attach the strap to the tool as shown in Fig. F and adjust for
proper balance and support.
1. Attach the strap mount.
2. Snap the shoulder strap latch
15
onto the strap
mount
14
located on the unit, just in front of the ON/
OFF trigger as shown in Fig.F. Adjust the strap so it
fits over yourshoulder and provides proper balance
andsupport.
Loading ...
Loading ...
Loading ...