Loading ...
Loading ...
Loading ...
additional safety instructions for a'ointer-pmaner ....
TO BECOME COMMONPLACE. ALWAYS REMEMBER
THAT A CARELESS FRACTION OF A SECOND IS
depth wanted, then raise the table to the desired depth_ SUFFICIENT TO INFLICT SEVERE INJURY.
14_:When planing, jointing, or beveling wood over:four (4)
feet Iongi make sure it is supported at table height.
17: Read and followthe instructions appearing on the danger
label on the cutter guard.
15.: Never leave the Jointer-Planer work area with the power
on; before the Jointer-Planer has come to a complete
stop, or without removing and storing the switch key.
16, Never operate the Jointer-Planer with protective cover
on the unused shaft end of the motor removed.
WARNING: THE 2" JOINTER-PLANER PULLEY AND
THE 2-1/2"" MOTOR PULLEY FURNISHED WILL RUN
THE CUTTER HEAD AT APPROXIMATELY 4300 RPM
WHEN USED WITH A 3450 RPM MOTOR. NEVER
SUBSTITUTE OTHER PULLEYS TO INCREASE THIS
SPEED BECAUSE IT COULD BE DANGEROUS.
WARNING: DO NOT ALLOW FAMILIARITY (GAINED
FROM FREQUENT USE OF YOUR JOINTER-PLANER)
3.
4.
DANGER
FOR YOUR OWN SAFETY
READ AND FOLLOW SAFETY INSTRUCTIONS IN
OWNERS MANUAL BEFORE OPERATING THIS MA-
CHINE.
NEVER OPERATE THIS MACHINE WITH THE CUT-
TER GUARD, SLIDING GUARD OR BELT GUARDS
REMOVED.
NEVER MAKE J01NTING OR PLANING CUTS DEEP-
ER THAN 1/16 INCH,
ALWAYS USE HOLD DOWN/PUSH BLOCKS FOR
JOINTING MATERIAL NARROWER THAN 3 iNCHES
OR PLANING MATERIAL THINNER THAN 3 INCHES.
The operation of any power tool can result in foreign
objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles complying
with ANSI Z87.1 (shown on Package) before commencing
power tool operation. Safety Goggles are available at Sears
retail or catalog stores.
cOntents
POWER TOOL GUARANTEE. ................... 2
GENERAL SAFETY INSTRUCTIONS FOR
POWER TOOLS .......................... 2
ADDITIONAL SAFETY INSTRUCTIONS FOR
JOINTER-PLANER ........................ 3
MOTOR SPECl FICATtONS AND ELECTRICAL
REQUIREMENTS ......................... 5
Connecting to Power Source Outlet ............ 5
Check Motor Rotation .................... 5
UNPACKING AND CHECKING CONTENTS ....... 6
ASSEMBLY ............................. 7
Mounting Jointer-Planer On Recommended
Craftsman Stand ........................ 7
Checking Cutterblade Screws ................ 7
Installing Sliding Guard .................... 8
Mounting Recommended Craftsman Motor and
8
Belt Guards ...........................
Check Motor Rotation. .................... 9
Jointer-Pulley Belt Guard Installation ........... 11
GETTING TO KNOW YOUR JOINTER-PLANER .... 12
Depth of Cut Handwheel .................. 12
Fence Locks and Stops .................... 13
Fence Tilt Scale ......................... 13
Cutterguard ............................ 15
Infeed Table ........................... 15
On-Off Switch .......................... 17
BASIC JOINTER-PLANER OPERATION ......... 19
Feeding the Workpiece .................... 19
Using the Hold Down/Push Blocks ............ 20
Beveling .............................. 21
MAINTENANCE .......................... 22
Replacing Cutter Blades.................... 22
Installing Cutter Guard Spring ............... 24
Sharpening Cutter Blades .................. 25
GENERAL MAINTENANCE .................. 26
WIRING DIAGRAM ........................ 26
LUBRICATION .......................... 26
TROUBLE SHOOTING ...................... 27
RECOMMENDED ACCESSORIES .............. 27
REPAIR PARTS ............. ............. 28
4
Loading ...
Loading ...
Loading ...