Loading ...
Loading ...
Loading ...
ENGLISH
5
EXTENSION CORDS
WARNING: Use proper extension cords. Make sure
your extension cord is in good condition and is a
3-wire extension cord which has a 3-prong grounding
type plug and matching receptacle which will accept
the machine’s plug. When using an extension cord,
be sure to use one heavy enough to carry the current
of the machine. An undersized cord will cause a
drop in line voltage, resulting in loss of power and
overheating. Minimum Gauge for Cord Sets
shows the correct gauge to use depending on the cord
length. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier thecord.
Minimum Gauge for Cord Sets
Volts
Total Length of Cord in Feet
(meters)
120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
American Wire Gauge
More
Than
Not
More
Than
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
The label on your tool may include the following symbols. The
symbols and their definitions are asfollows:
V ......................... volts
Hz .......................hertz
min ..................... minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................watts
or AC ...........alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n
o
.......................no load speed
n .........................rated speed
......................earthing terminal
.....................safety alert symbol
.....................visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Specifications
Input 120V AC, 15 Amp
No-load speed 10000 RPM
Feed speed 14' (4.3 m) or 26' (7.9 m) per minute
Planing height Maximum 6" (152.4 mm)
Minimum 1/8" (3.2 mm)
Planing width Maximum 13" (325 mm)
Planing depth Maximum 1/8" (3.2 mm) (for boards 6" [152 mm]
wide or less)
Electrical Connection
Be sure your power supply agrees with the nameplate
marking. Volts, 50/60 Hz or “AC only” means your planer
must be operated only with alternating current and never
with direct current. Voltage decrease of more than 10%
will cause loss of power and overheating. All
DeWALT
tools
are factory tested, if this tool does not operate, check the
powersupply.
Intended Use
This planer is designed for professional woodworking.
DO NOT use under wet conditions or in presence of
flammable liquids orgases.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
Fan-Assisted Chip Ejection System
Your planer is equipped with a fan-assisted chip ejection
system to aid in exhausting chips from the unit. The fan-
assisted chip ejection system will work in conjunction with
independent dust collectionsystems.
NOTE: It is not recommended that a shop vac be
connected to the DW735. The capacity of most vacs does
not support the volume of chips ejected during planing.
The vacuum hose may clog stopping the flow of chips. It is
recommended to use the dust collection system to clean
debris from the interior of thetool.
See the Troubleshooting Guide, for additionalinformation.
Automatic Carriage Lock
There is no manual carriage lock on your planer. A
device that automatically minimizes the movement that
causes snipe during planing is designed into the four
threadedposts.
ASSEMBLY AND ADJUSTMENTS
WARNING: Do not remove guards (
7
, Fig.D).
Serious injury couldresult.
Fig. D
7
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can causeinjury.
Loading ...
Loading ...
Loading ...