Loading ...
Loading ...
Loading ...
English
English
18 19
1. Press the Alternator Check Button to start the check. The backlit
LCD screen will display the following to indicate the unit is analyzing
the alternator:
The Battery Status Icon will light solid and the Alternator Icon will
flash.
2. If the unit detects that the alternator is good, the backlit LCD screen
will display the following:
The Battery Status Icon, Alternator Icon, and “ALT GOOD” will light
solid.
3. If the unit detects that the alternator is out of typical voltage range,
the backlit LCD screen will display the following:
The Battery Status Icon, Alternator Icon and “ALT” will light solid.
The Fault Icon will flash.
4. Press the Alternator Check Button again to stop the test and turn
off the unit.
IMPORTANT: Always turn the unit off when not in use. Recharge this
unit fully after each use.
Portable Compressor
The built-in 12 volt DC compressor is the ultimate compressor for all
vehicle tires, trailer tires and recreational inflatables. A nozzle adaptor
is supplied that screws onto the end of the Sure Fit
®
nozzle at the free
end of the compressor hose. The compressor hose with tire fitting is
stored on the compressor hose bracket on the right side of the unit.
Refer to the “Features” illustration for locations of compressor hose.
The Compressor Power Button and Increase ( ) and Decrease ( )
Compressor Pressure Control Buttons are located on the control panel
on the front of the unit.
Before proceeding, check the unit’s battery status on the LCD screen.
Four solid bars in the battery icon indicates a full battery. When the
battery level is nearly empty with only one solid bar, the unit MUST be
recharged before use or the unit’s built-in low voltage protection will
activate. The empty Battery Status Icon will flash for a short period of
time before automatic shut down.
The compressor is capable of inflating up to 120 pounds per square
inch (psi) pressure. Return hose to the storage bracket after use.
WARNING – To reduce the risk of serious injury or property damage:
Follow all safety instructions found in the “Specific Safety Instructions
for Compressors” section of this instruction manual.
CAUTION – To reduce the risk of serious injury or property damage:
When the compressor is operated at a low PSI, the unit may start in
low and gradually rev up. When the compressor is operated at higher
PSIs, the unit may operate normally for several minutes, then rev down
for a few minutes before returning to normal operation. This feature
protects the unit from overheating during normal use. In any event, do
not operate compressor continuously for longer than 10 minutes, as
it may overheat. This could damage the compressor. If the compressor
must be operated for longer periods: every 10 minutes press the
Compressor Power Button to turn the compressor off, then restart
after a cooling down period of approximately 30 minutes. In any event,
the compressor will automatically shut down after operating
continuously for 10 minutes.
INFLATING TIRES OR PRODUCTS WITH VALVE STEMS
1. Screw the Sure Fit
®
nozzle onto the valve stem. Do not overtighten.
2. Press the Compressor Power Button. A beep will sound and the
backlit LCD screen will display the following:
The Compressor Icon will light and the digital display will alternately
show the flashing pre-set psi value (that was last set by the
compressor pressure control buttons) and the current pressure of
the item being inflated (which will light solid).
3. Press the “ ” and “ ” Pressure Control Buttons to set the desired
pressure from a range pre-set values (between 3 and 120), which
will display on the backlit LCD screen. The unit will sound a beep
with each press of the buttons (holding the button speeds up the
upward or downward value selection). Once the desired pressure
has been entered, release the button and the flashing digital display
will show the new selected pressure, as follows:
The new selected value is now stored in the unit’s memory until it
is manually reset.
4. Press the Compressor Power Button once more to begin inflating.
The Compressor Icon will flash and the digital display will only show
the current pressure value (which will light solid) to indicate the
compressor is activated. Monitor the pressure on the LCD screen.
IMPORTANT NOTE: To interrupt during inflation, press the
Compressor Power Button again.
5. When desired pre-set pressure is reached, the compressor will
automatically stop.
6. Press the Compressor Power Button again to turn off the unit.
7. Unscrew and remove the Sure Fit
®
nozzle from the valve stem.
8. Allow the unit to cool, then recharge before storing away.
9. Store the compressor hose and Sure Fit
®
nozzle in storage bracket.
INFLATING OTHER INFLATABLES WITHOUT VALVE STEMS
Inflation of other items requires use of the nozzle adapter.
1. Screw the nozzle adapter into the Sure Fit
®
nozzle. Do not
overtighten.
2. Insert the nozzle adapter into item to be inflated.
3. Follow steps 2 through 4 of the “Inflating Tires or Products With
Valve Stems” section.
DXAEPS14_ManualENSP_020221.indd 18-19DXAEPS14_ManualENSP_020221.indd 18-19 2/2/2021 10:56:31 AM2/2/2021 10:56:31 AM
Loading ...
Loading ...
Loading ...