Loading ...
Loading ...
Loading ...
SPECIFIC SAFETY RULES
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect the
tool's operation. A guard or other part that is damaged
should be properly repaired or replaced.
• DIRECTION OF FEED. Feed work into a knife against the
direction of rotation of the knife only.
• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER OFF. Don’t leave tool until it comes to a complete
stop.
• DO NOT ALTER OR MISUSE THE TOOL. Any alteration
or modication is considered misuse and may result in
serious personal injury.
BEFORE OPERATING
• Check for proper assembly and proper alignment of
moving parts. Understand the function and proper use
of the ON/OFF switch.
• Know the condition of the scroll saw. If any part is missing,
bent or does not operate properly, replace the component
before you use the scroll saw.
• Determine the type of work you are going to be doing.
Properly protect your body including your eyes, hands,
face and ears.
• To avoid injury cause by pieces thrown from accessories,
use only recommended accessories designed for this saw.
Follow this instruction supplied with the accessory. The
use of improper accessories may cause risk of injury.
• To avoid contact with rotating equipment:
• Do not position your ngers where they could contact
the blade if the workpiece should unexpectedly shift or
your hand should slip.
• Do not cut a workpiece too small to be held safely.
• Do not reach under the scroll saw table when the motor
is running.
• Do not wear loose clothing or jewelry. Roll long sleeves
above the elbow. Tie back long hair.
• To avoid injury from a re hazard, do not operate the scroll
saw near ammable liquids, vapours or gases.
• To avoid back injury:
• Obtain help when it is necessary to raise the scroll saw
more than 10" (25.4 cm). Bend your knees when lifting
the scroll saw.
WHEN OPERATING THE SCROLL SAW
• To avoid injury from unexpected scroll saw movement:
• Use the scroll saw on a rm, level surface with adequate
space for handling and supporting the workpiece.
• Be sure the scroll saw cannot move when operated.
Secure the scroll saw to a workbench or table with wood
screws or bolts with washers and nuts.
• Before moving the scroll saw, unplug the power cord from
the electrical outlet.
• To avoid injury from kickback:
• Hold the workpiece rmly against the tabletop.
• Do not feed the workpiece too fast while cutting. Only
feed the workpiece at the rate the saw will cut.
• Install the blade with the teeth pointing downward.
• Do not start the saw with the workpiece pressing against
the blade. Slowly feed the workpiece into the moving
blade.
• Use caution when cutting round or irregularly shaped
workpieces. Round items will roll and irregularly shaped
workpieces can pinch the blade.
• To avoid injury when operating the scroll saw:
• If you are not thoroughly familiar with the operation of
scroll saws, obtain advice from a qualied person.
• Before starting the saw, make sure the blade tension is
correct. Recheck and adjust tension as needed.
• Make sure the table is locked into position before
starting the saw.
• Do not use dull or bent blades.
• When cutting a large workpiece, make sure the material
is supported at the table height.
• Turn the saw OFF and unplug the power cord if
the blade jams in the workpiece while being backed out.
This condition is usually caused by sawdust clogging
the line you are cutting.
• Do not use if blade guard is damaged or missing.
• Do not clear away cut-off pieces until blade has stopped
and the saw is turned off.
SAFETY INSTRUCTIONS
Page 5
WARNING: This product is not recommended for
drilling.
READ OPERATOR’S MANUAL
To reduce the risk of injury, user must read and
understand operator’s manual before using this product.
• USE SAFETY GOGGLES AND EAR PROTECTION
• ALWAYS WEAR EYE PROTECTION THAT CONFORMS
WITH UL REQUIREMENTS. FLYING DEBRIS can cause
permanent eye damage.
Loading ...
Loading ...
Loading ...