Craftsman 13953992 garage door opener

User Manual - Page 21

For 13953992.

PDF File Manual, 76 pages, Download pdf file

Loading ...
Loading ...
Loading ...
INSTALLATION STEP 7
Install the Door Control
Locate door control within sight of door, at a minimum
height of 5 feet (1.5 m) where small children cannot
reach, away from moving parts of door and door
hardware. If installing into drywall, drill 5/32" (0.40 cm)
holes and use the anchors provided. For pro-wired
installations (as in new home construction), it may be
mounted to a single gang box (Figure 2).
1. Strip 7/16" (11 mm) of insulation from one end of
bell wire and connect to the two screw terminals on
back of door control by color: white wire to 2 and
white/red wire to the 1.
2. Remove white cover by gently prying at slot in top
of the cover with a small flat head screwdriver.
Fasten with 6AB x 1-1/4" self-tapping screws
(drywall installation) or 6-32 x 1" machine screws
(into gang box) as follows:
Drill and install bottom screw, allowing 1/8" (3 mm)
to protrude above wall surface.
Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
Drill and install top screw with care to avoid
cracking plastic housing. Do not over tighten.
Insert top tabs and snap on cover.
3. (Standard installation only) Run bell wire up wall
and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Do not
pierce wire with a staple, creating a short or open
circuit. If your access door is near the garage door,
you may run this wire with the Safety Reversing
Sensor wires along the top of the rail. See page 18.
4. Insert all wires through the opening on top of motor
unit above the terminal block on the back panel
(Figure 3).
5. Strip 7/16" (11 mm) of insulation from each set of
wires. Insert door control wire into quick-connect
terminals by color: white wire to white, white/red
wire to red.
Separate white and white/black wires sufficiently to
connect to the opener quick-connect terminals. Twist
like colored wires together. Insert wires into quick-
connect holes: white to white and white/black to
grey.
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires
into quick-connect holes: white to white and red/white
to red.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
Be sure power is not connected BEFOREinstalling door
control.
Connect ONLYto 24 VOLT low voltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a
closing garagedoor:
Install door control within sight of garage door, out of
reach of children at a minimum height of 5 feet, and
awayfrom all moving parts of door.
NEVERpermit children to operate or play with door
control push buttons or remote control transmitters.
Activatedoor ONLYwhen it can be seen clearly,is properly
adjusted,andthere are no obstructions to door travel.
ALWAYSkeep garage door in sight until completely
closed. NEVERpermit anyone to cross path of closing
garagedoor.
Hardware Shown Actual Size
lnsulated
(drywall installation) Staples
(gang box installation) Dry Wall Anchors
Outside Keylock Accessory Connections
To opener quick-connect terminals: white to white;
wh te/red to red.
CONTROL
CONSOLE Top
Mounting Hole
Terminal
Lighted Screws
Push
Button igh Bottom
Lock BACK VIEW Mounting Hole
Figure 1
REMOVE & REPLACE COVER
TO Replace, To Remove_
insert Top _ _ Twist
Tabs_ _First ///_ -__ Here
Figure 2
PRB-WIRED
INSTALLATION
Figure 3 Wiring toTerminal Block
Strip 7/16" (1t mm) of insulation from each wire.
insert wires through opening on top of motor
24 Volt
2-Condu_or
Bell Wi_ in
Gang Box
unit above terminal block then _nto qu_ck
and manual release/safety reverse test label in a " " , " " - /
.... connect terminals.
prominent location on _ns_deof garage door. /c
................ Door Control To release wire, push in tab /\_
/vu t _-: uu Nut connect the power ano operate the Connections withscrewdrivertip _
opener at this time. The trolley will travel
7/16
to the full open position but will not return " _ [-_'
(11ram t -_'_
to the close position until the sensor _-_ _-_ "__
beam is connected and properly aligned. Strip wire 7/16" (11 ram)
White Grey
Sensors
21
Loading ...
Loading ...
Loading ...