Loading ...
Loading ...
Loading ...
USE AND CARE
OPERATION
Forbest results, alwaysturn on your hood before you begin
cooking. Let hood run for a few minutes after you turn off
range to allow hood to clear the air in the kitchen.
Pull out hood front to turn on blower and light. Light can
also be turned on when hood front Isclosed, The hood front
must be out and the speed control turned on for the blower
to start.
SPEED CONTROL
speeds and sound I_vels. 1"hecontrol turns the blower on
to high speed and dials down to low speeds,
With speed_control turned on, blower will start when hood
front is pulled out end will run at whatever previous speed
you have chosen,
HEAT SENTRY"
Your hood is equipped with a Heat SentryTM thermostat.This
thermostatis.s devicethat willturnon or speed up the blower
if it sensesexcessiveheat above the cookingsurface.
If blower Is not on, or if it is running at low speed, the Heat
Sentry" will override the normal blower control and turn
blower on to high speed. The blower will run until
tern peratures drop to normal levels. The blower will then
return to its original setting.
LIGHT
The light switch is located just to the left of the speed
control. Turn on light by pulling front of hood out or, If you
don't need the blower, just flip the switch for cooktop or
night-lighting,
CLEANING
Clean hood with a mild detergent suitable for painted
surfaces. DO NOT USE ABRASIVE CLOTH, STEEL WOOL
PADS OR SCOURING POWDERS.
To clean blower, remove blower compartment cover and
vacuum blower. Blower motor Is lifetime lubricated and
never needs oiling, Do not Immers+eblower In water.
FI LTE R
The aluminum filter in your hood should be cleaned
frequently with detergent to avoid grease buildu;). The
filter Is dishwasher safe. To remove filter, rotate retaining
clips on either side offilter opening out of the way and pull
filter out of hood.When replacing filter, make sure pulltabs
on filter aretoward bottom and to the back of hood.
SERVICE
CAUTION
l
ALWAYS DISCONNECT ELECTRIC POWER SUPPLY
TO HOOD BEFORE SERVICING. !
Your hood uses an F2OT12 fluorescenttube, available at
most hardware stores or home,centers.
If tube flickers or does not light,check the prongs on ends
oftube to make sure that they are properly seated in tube
holders. Slide prongs into holders and rotate tube so that
holders grip prongs and hold tube in place. If tube
continues to flicker or does not light, replace tube.
Ifends of the tube light but center does not,the starter may
be defective. Your hood uses an FS-2 starter, located on
underside of control unit. Remove old starter by pushing it
in and turning itcounterclockwise. Purchase a new starter
at your local hardware store or home center, and install it
by pushing it in and turning it clockwise.
If tube still does not light, order a 97007428 Ballast
Transformer Kit from your Broan Distributor or from the
Broan Service Department. W_ite Broan Mfg. Co., Inc., P.O.
Box 140, Hartford, WI 5.3027.
It_
BLOWER
KNURLED NUT_
HOW TO AVOID A COMMON RANGE-TOP GREASE FIRE
Your range hoodprovidesa protectivebarrierbetweenthe cook-
ing surfaceand the cabinets.
Keepfen, filters and grease ladensurfacesCLEAN accordingto
instructions.
• AlwaysturnhoodON whencookingat highheatto keep the cook_
mg area and the hoodcooler,
Use high heat settingsonlywhen necessary.
Never leave cookingsurface unattended.Boll-overcausessmok_'
ing and grea_;yspilloversthat may ignite.
Alwaysuse adequate-sized utensils.
If preparingflamingfoods, suchas CherriesJubilee, alwaysturn
hoodON toHIGH topreventa highheatsituationwhichcancause
damage or fire.
HOW TO EXTINGUISH A COMMON RANGE-TOP GREASE
FIRE
=,Neverplckupa flamingpan+lfdropped,flamescanspreedqulckly.
DO NOT USEWATER! A violentsteam explosionmay result.Wet
dishclothsor towelsare also dangerous.
i motherflames witha closefitting lid,cookiesheetor metaltray.
Flaminggreasecanalsobeexti.r_ulshedwithbakingsodaora multi-
purposedry chemicalextinguisher.
Turn off surfaceunits - if you can do sowithoutgettingburned.
TO REMOVE BLOWER FOR SERVICE
1. Remove fluorescent tube.
2. Rotate filter retaining clips out ofway and remove filter.
3. Unplug blower and back off knUrled nuts to ends of
blower mounting rods. Do not remove nuts completely
from rods, Support blower with one hand and swing
rods out of the way. Do not grasp blower by blower
wheeis..Wheeis may be damaged,
Loading ...
Loading ...
Loading ...