Loading ...
Loading ...
Loading ...
E-103
1. In the Timekeeping Mode, pull the crown out.
• This displays the city code setting screen.
2. Rotate the crown to select the city code nearest the location whose
sunrise and sunset times you want to check.
• If you do not need to specify a longitude and latitude, jump to step
7 h
e
re.
3. Press
B
twice to switch to the latitude setting screen.
4. Rotate the crown to adjust the latitude setting.
• Latitude can be specifi ed in the range shown below.
65
.0°S (65.0 degrees south latitude) to 0°N to 65.0° (65.0 degrees
north latitude)
5. Press
B
to switch to the longitude setting screen.
6. Rotate the crown to adjust the longitude setting.
• Longitude can be specifi ed in the range shown below.
17
9.9°W (179.9 degrees west longitude) to 0°E to 180.0°E (180.0
degrees east longitude)
7. Push the crown back in.
8. Use
B
to select the Sunrise/Sunset Mode as shown on page E-30.
• This displays the sunrise/sunset times of the location you
spec
i
fi ed.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Latitude
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Longitude
E-102
To view the sunrise/sunset time for a particular date
While the sunrise/sunset time is on the display, press
A
and then select a date.
• Pressing
A
causes today’s date to appear on the digital display. After that, each press of
A
advances the day by 1.
• The sunrise/sunset times of the selected date will appear when you release the
A
button.
• Holding down
A
scrolls at high speed.
• You can select any date through December 31, 2099.
To look up the sunrise and sunset times for a specifi c location
Important!
•
First, select the city code of the city that is closest to the location whose sunrise/sunset times you want
to look up. Next, input the location’s latitude and longitude.
• After you are fi nished looking up the times you want, return the city code to what it was before you
changed it. If you input a latitude and longitude without changing the city code, re-input their original
settings. Failure to do so will cause the wrong time to be displayed.
• For information about the Home City setting, see “Confi guring Home City Settings” (page E-34).
E-101
Looking up Sunrise and Sunset Times
You can use the Sunrise/Sunset Mode to look up the sunrise and sunset times for a particular date (year,
month, day) and location.
To enter the Sunrise/Sunset Mode
Use
B
to select the Sunrise/Sunset Mode as shown on page E-30.
•
SUN
will appear on the display. After about one second, the date in
the currently selected city will appear. After about another two
seconds, the sunrise time and sunset time will alternate on the display.
• If you are using 12-hour timekeeping, the
P
(p.m.) and
A
(a.m.)
indicators will also appear on the display.
• Before trying to use the Sunrise/Sunset Mode, you need to confi gure
settings for the city code, longitude, and latitude for the location whose
sunrise and sunset times you want to view.
• The factory default confi guration of the location is: City Code:
TYO
(Tokyo); Latitude: North 35.7 degrees; Longitude: East 139.7 degrees.
Note
• If you think that the sunrise and/or sunset times are not correct for
some reason, check the watch’s city code, longitude and latitude
settings.
• The sunrise and sunset times displayed by this watch are times at sea
level. Sunrise and sunset times are different at altitudes other than sea
level.
Current date
Sunrise time
Sunset time
Alternates
every two
seconds.
E-100
4. Press
B
.
5. Rotate the crown to change the hour setting.
6. Push the crown back in. This completes the calibration operation.
• Performing the above procedure allows the Tide Graph hand to indicate more accurate tide
inf
o
rmation.
• The Tide Graph and Moon Age information you can view in the Tide/Moon Data Mode changes in
ac
cordance with the date you specify in step 1 of the above procedure. If you want to view Tide
Graph and Moon Age information for a particular date, to back to step 1 and specify the date.
• The calibration setting you make with this procedure is also applied to Tide Graph information
in
dicated in other modes besides the Tide/Moon Data Mode.
E-99
5. Press
C
to return to the tide indication.
• The tide at 6:00 a.m. on the date you specifi ed in step 4 will be indicated.
• You can use the same operation as in step 2 of this procedure to specify a time.
Calibrating the High Tide Time
You obtain more accurate tide indications by the watch by calibrating its high tide time with information
you can fi nd on the Internet or in a newspaper.
• Note that the high tide time differs according to your location and the current season.
To calibrate the high tide time
1. Perform steps 1, 3, and 4 under “To view the tide level and Moon age for a specifi
c date and time” and
then specify the date whose high tide time you want to calibrate.
2. Pull out the crown.
• This will cause the hour and minute digits of the high tide time to
fl a s
h .
3. Rotate the crown to change the minute setting.
• The hour setting will change in accordance with minute setting
ch
anges. To set the hour hand separately, go to step 4 of this
procedure.
• Any time during steps 3 through 5, you can discard your changes
an
d return to the high tide time for the date that was previously
selected by pressing
A
and
C
at the same time.
• If there are two high tides on a date, set the time of the fi rst high tide. The watch will automatically
ca
lculate the time of the second one.
• If summer time is turned on for your Home Time (DST di
splayed), you should also use summer
time when setting the high tide time (page E-34).
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Hour : Minutes
E-98
3. Press
C
.
• This displays information in the following sequence: MOON ➝ To
day’s Moon age.
Today’s Moon age
Tide level
not indicated
D
• The Moon age is for noon on the current date, regardless of the indicated time.
• Calculation error for the Moon age is ±1 day.
4. Use
A
to specify the date you want.
You can use this screen to check the Moon age on the specifi
ed date.
• Pressing
A
wi
ll cause today’s date to appear on the display. After that, you can use
A
(forward)
to scroll the date.
• Holding down
A
sc
rolls at high speed.
• About two seconds after you display the desired date, the Moon age on that date appears.
• You can select any date through December 31, 2099.
• To view the tide level for a specifi ed date and time, go to step 5 of this procedure.
E-97
• If the Tide Graph hand indication is not correct, check the Timekeeping Mode time and date, and the
Home City settings. If this does not correct the problem, refer to “Calibrating the High Tide Time” (page
E-99).
Viewing the Current Moon Age
In the Timekeeping Mode, you can view today’s Moon age by pressing
C
a number of times. See
“Timekeeping” (page E-33).
To view the tide level and Moon age for a specifi c date and time
1. Use
B
to enter the Tide/Moon Data Mode as shown on page E-30.
• The display will change as shown below and the tide level at 6:00 a.m. today will be indicated.
Tide level at 6:00 a.m.
for today
2. Use
A
(+1 hour) to specify the time you want.
• The Tide Graph changes in accordance with the time setting.
• Holding down
A
sc
rolls at high speed.
• To view tide level and Moon age information for another date, go to step 3 of this procedure.
E-96
Checking the Tide Level and Moon Ages (Tide/Moon)
You can use the watch to check the current tide level and Moon age.
• Current tide level and Moon age information is displayed for the currently selected Home Time City.
You can also check information for another city by changing to a different Home City (page E-34).
• Note that the tide and Moon information displayed by this watch is approximate and is intended as
general information only. Never try to use it for marine navigation or any other purposes requiring
accurate measurements.
Viewing the Current Tide Level
In the Timekeeping Mode, the small hand indicates the current tide level.
• The tide level is indicated as one of six levels.
• Besides the Timekeeping Mode, the small hand indicates the tide level
in all modes except in the cases below.
– Each sensor mode
– When barometric pressure change indication is enabled (
BARO
displayed)
– While the crown is pulled out
– In the Tide/Moon Data Mode*
*
The tide level at a specifi ed time is indicated in the Tide/Moon Data Mode.
• The tide in the Home City is indicated even while the watch is in the
World Time Mode.
• When barometric change indication (page E-49) is enabled (
BARO
displayed), the small hand acts as the barometric pressure change
indicator. You can disable the barometric pressure change indication
(
BARO
not displayed) by holding down
C
for at least of two seconds
in the Barometer Mode.
Tide (Tide Graph hand)
Operation Guide 5477
Loading ...
Loading ...
Loading ...