Use Restrictinos
Battery and Charging
•Plastic bags are dangerous. Please keep them away from infants and children as they may pose a choking hazard.
•This product is only intended to be used to clean floors in residential households. Do not use this product outdoors (such as open balconies), on surfaces
other than floors (such as sofas) or in commercial/industrial environments.
•Do not use this product on a suspended platform, such as a balcony, which does not have any guardrails.
•Do not operate this product if the environment above 40 degrees Celsius, below 0 degrees Celsius or when any liquid or sticky material is present on the
ground.Before using, please remove any wires on the ground to avoid dragging the wires when the robot is running.
•Please put away the fragile items and sundries (such as vases, plastic bags, etc.) ,to avoid the damage of valuables due to the obstruction or collision of the
device during operation.
•Do not allow persons (including children) who lack physical, intellectual or experience or common sense to use this product without supervision or
guidance from someone capable of properly operating this product.
•Do not allow children to use this device as a toy.
•Do not place the main brush cleaner in an area accessible to children.
•Do not let human or pet hair, fingers near the suction port when the main machine is in operation.
•Do not use this product to clean any burning objects (such as unextinguished cigarette butts).
•Do not allow the device to absorb hard or sharp objects (such as decoration waste, glass, nails, etc.)
•Do not use the laser sensor protection cover, the main engine cover and the collision buffer as handles to carry the machine.
•To clean and maintain the machine and dust collection charging dock, the operator must turn it off firstly and pull the plug from the socket and disconnect
the power.
•Do not soak the main machine and dust collection dock in water or clean with water.
•Do not use a wet cloth or any liquid to wipe any part of the product.
•Do not mop on a carpet environment.
•Please use the product in accordance with the instructions of the manual. Any damage or injury caused by improper use shall be borne by the user.
•It is forbidden to burn products even when they are severely damaged, as the batteries may explode.
•Do not use any third party batteries, chargers and charging piles.
•Do not disassemble, repair or modify the battery or charging pile without authorization.
•Do not place the charging pile near the heat source (such as radiator).
•Do not wipe or clean the shrapnel of the charging pile with wet cloth or hands.
•Do not throw away the discarded battery at will. It should be disposed of by a professional recycling institution.
•If the power cord is damaged, it must be replaced by a professional from the manufacturer, its maintenance department or similar department in order to
avoid danger.
•If you need to transport the product, please ensure that the mainframe is switched off and it is recommended to use the original packaging box.
•Do not pour water into the device or immerse the device in water.
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
Correct Disposal of this product
•If not used for a long time, please turn off the mainframe after full charge and put it in a cool and dry place, and charge it at least once every 3 months to avoid
damage to the battery due to over-discharge.
•To remove the battery, use the right tools. First remove the bottom cover screw, then open the bottom cover of the product, unplug the battery connecting
terminal and remove the battery from the battery box.
•The battery must be removed from the appliance before it is discarded.
•When the battery is removed, the appliance must be powered off.
•If the symbol for detachable supply unit is used, its meaning shall be explained. ‒ symbol IEC 60417-6181
•For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.
Class 1 laser products, the product radar in accordance with the GB7247.1-2012/IEC 60825-1.2014 Class 1 laser safety standards, will not produce
dangerous laser radiation to the human body.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this
product for environmentally safe recycling.
Declaration of Conformity
We (Manufacturer is responsible for this declaration)
Ekoo Electronic Co.,Ltd.
(Company name)
B09,block B,f2,bldg.b,runfeng Pioneer Park,no.973, minzhi Avenue,
Minzhi St., Longhua, Shenzhen, CN.
(Company address)
declare under our sole responsibility that the product
Trade name: HONITURE
Equipment: robot vacuum cleaner
Model No. : Q6 pro
to which this declaration relates is in conformity with the essential
requirement set out in the Council Directive on the Approximation of
the laws of the Member States relating to LVD Directive(2014/35/EU)
& EMC Directive(2014/30/EU) & RoHS(2011/65/EU) product is
responsible to affix CE marking, the following standards were applied:
EN300 328 V2.1.1
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
EN 55032:2015
EN 55035:2017
EN 62368:2014
EN 50665:2017
IEC62321-3-1:2013
IEC62321-4:2013
IEC62321-5:2013
IEC62321-6:2015
IEC62321-7-1:2015
IEC62321-7-2:2017
IEC62321-8:2017
Full Name: George.wang Position: Approbation Manager
Signature: George.wang Place/Date: Shenzhen,China/Aug.17-2021
Dichiarazione di conformità
Noi (il produttore è responsabile di questa dichiarazione)
Ekoo Electronic Co., Ltd.
(Nome della ditta)
B09, blocco B, f2, bldg.b, runfeng Pioneer Park, no.973, minzhi
Avenue, Minzhi St., Longhua, Shenzhen, CN.
(Indirizzo aziendale)
dichiariamo sotto la nostra esclusiva responsabilità che il prodotto
Nome commerciale: HONITURE
Equipaggiamento: robot aspirapolvere
Modello n.: Q6 pro
cui si riferisce la presente dichiarazione è conforme al requisito
essenziale stabilito nella Direttiva del Consiglio sul ravvicinamento
delle legislazioni degli Stati membri relativa alla Direttiva LVD
(2014/35/UE) e alla Direttiva EMC (2014/30/UE) e Il prodotto RoHS
(2011/65/UE) è responsabile dell'apposizione della marcatura CE,
sono stati applicati i seguenti standard:
EN300 328 V2.1.1
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
EN 55032:2015
EN 55035:2017
EN 62368:2014
EN 50665:2017
IEC62321-3-1:2013
IEC62321-4:2013
IEC62321-5:2013
IEC62321-6:2015
IEC62321-7-1:2015
IEC62321-7-2:2017
IEC62321-8:2017
Nome completo: George.wang Posizione: responsabile dell'approvazione
Firma: George.wang Luogo/Data: Shenzhen, Cina/Aug.17-2021
Konformitätserklärung
Wir (Hersteller ist verantwortlich für diese Erklärung)
Ekoo Electronic Co.,Ltd.
(Name der Firma)
B09,block B,f2,bldg.b,runfeng Pioneer Park,no.973, minzhi Avenue,
Minzhi St., Longhua, Shenzhen, CN.
(Firmenadresse)
erklären in alleiniger Verantwortung, dass das Produkt
Handelsname: HONITURE
Ausstattung: Roboterstaubsauger
Modell-Nr.: Q6 pro
auf die sich diese Erklärung bezieht, mit den grundlegenden
Anforderungen der Richtlinie des Rates zur Angleichung der
Rechtsvorschriften der Mitgliedstaaten in Bezug auf die Niederspan-
nungsrichtlinie (2014/35/EU) und die EMV-Richtlinie (2014/30/EU)
und RoHS(2011/65/EU) Produkt ist verantwortlich für die Anbringung
der CE-Kennzeichnung, die folgenden Standards wurden angewen-
det:
EN300 328 V2.1.1
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
EN 55032:2015
EN 55035:2017
EN 62368:2014
EN 50665:2017
EN 50665:2017
IEC62321-3-1:2013
IEC62321-4:2013
IEC62321-5:2013
IEC62321-6:2015
IEC62321-7-1:2015
IEC62321-7-2:2017
IEC62321-8:2017
Vollständiger Name: George.wang Position: Approbation-Manager
Unterschrift: George.wang Ort/Datum: Shenzhen,China/Aug.17-2021
Declaration de Conformité
Nous (Le fabricant est responsable de cette déclaration)
Ekoo Electronic Co.,Ltd.
(Nom de la société)
B09, Block B, F2, Bldg.B, Runfeng Pioneer Park,No.973, Minzhi
Avenue, Minzhi St., Longhua, Shenzhen, CN
(Adresse de la société)
attestons sous notre unique responsabilité que le produit:
Nom commercial : HONITURE
Equipement : robot aspirateur
N°de modèle : Q6 pro
auquel cette déclaration se rapporte est conforme à l'exigence
essentielle énoncée dans la directive du Conseil sur le rapproche-
ment des législations des États membres relatives à la directive LVD
(2014/35/UE) et à la directive CEM (2014/30/UE) et Le produit RoHS
(2011/65/UE) est chargé d'apposer le marquage CE, les normes
suivantes ont été appliquées :
EN300 328 V2.1.1
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
EN 55032:2015
EN 55035:2017
EN 62368:2014
EN 50665:2017
IEC62321-3-1:2013
IEC62321-4:2013
IEC62321-5:2013
IEC62321-6:2015
IEC62321-7-1:2015
IEC62321-7-2:2017
IEC62321-8:2017
Nom complet : George.wang Poste : Responsable de l'approbation
Signature : George.wang Lieu/Date : Shenzhen, Chine/17 août-2021
Declaración de conformidad
Nosotros (el fabricante es responsable de esta declaración)
Ekoo Electronic Co.,Ltd.
(Nombre de empresa)
B09,bloqueB,f2,bldg.b,runfeng Pioneer Parque ,no.973, minzhi
Avenida, Minzhi CL., Longhua, Shenzhen, CN.
(Dirección de la empresa)
Declaramos bajo nuestra exclusiva responsabilidad que el producto
Nombre comercial: HONITURE
Equipo: robot aspirador
No. del modelo: Q6 pro
a lo que se refiere esta declaración está en conformidad con el
requisito esencial establecido en la Directiva del Consejo sobre la
Aproximación de las leyes de los Estados Miembros en relación con
la Directiva LVD(2014/30/EU) y la Directiva EMC (2014/30/EU) &
RoHS(2011/65/EU) El producto es responsable de colocar la marca
CE, se aplicaron las siguientes normas:
EN300 328 V2.1.1
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
EN 55032:2015
EN 55035:2017
EN 62368:2014
EN 50665:2017
IEC62321-3-1:2013
IEC62321-4:2013
IEC62321-5:2013
IEC62321-6:2015
IEC62321-7-1:2015
IEC62321-7-2:2017
IEC62321-8:2017
Nombre completo: George.wang Cargo: Gerente de aprobación
Firma: George.wang Lugar / Fecha: Shenzhen, China / 17 de agosto
de 2021
