Loading ...
Loading ...
Loading ...
- 3
The appliance works best while in the
operating position.
3 "OFF" position
Motor off
1 Activate parking brake
2 Parking brake released
To unload the machine, proceed as follows:
Remove the cardboard.
Manually lift appliance off the pallet.
Kerb weight: approximately 70 kg
or
Fold up and install the push handle.
Then use the push handle to pull the
appliance off the pallet.
Loosen the star handle screw.
Align the pushing handle.
Tighten star handle screw.
Danger
Risk of explosion!
Only fuel up while motor is turned off.
Only use the fuels specified in the Op-
erations Manual.
Do not refuel the machine in enclosed
spaces.
Smoking and naked flames are strictly
prohibited.
Ensure that no fuel reaches the hot
open surfaces.
1 Filling nozzle
2 Tank lid
Switch off engine.
Open fuel filler cap.
Use "regular unleaded petrol".
Tank filling with empty tank approx. 0.9
litre.
Wipe off any spilt fuel and close fuel fill-
er cap.
Check engine oil level.
Check air filter.
Check tyre pressure.
Check the roller brush for wear and
wrapped belts.
Check the height adjustment of the roll-
er brush.
Check for smooth running of the
Bowden cables and the moveable parts
Empty waste container (option).
Check the fuel filler cap and other clo-
sures and replace if damaged.
Check the sound absorber and replace
if necessary.
Note: For description, see section on Care
and maintenance.
DANGER
Long hours of using the appliance can
cause circulation problems in the hands on
account of vibrations.
It is not possible to specify a generally valid
operation time, since this depends on sev-
eral factors:
– Proneness to blood circulation deficien-
cies (cold, numb fingers).
– Low ambient temperature. Wear warm
gloves to protect hands.
– A firm grip impedes blood circulation.
– Continuous operation is worse than an
operation interrupted by pauses.
In case of regular, long-term operation of
the device and in case of repeated occur-
rence of the symptoms (e.g. cold, numb fin-
gers) please consult a physician.
Activate parking brake.
Open fuel cock.
Turn the rotating knob parallel to the
hose of the fuel tap.
Gas lever in " CHOKE" position.
Pull the starter rope slowly until a resist-
ance can be felt.
Pull starter rope swiftly.
Once the motor runs, release the starter
rope. In order to work, put gas lever in
the "full load" position.
DANGER
Risk of injury! During work, the roller brush
can eject stones or loose chippings to-
wards the front or sides. Make sure that this
does not endanger persons, animals or ob-
jects.
CAUTION
Do not sweep up packing strips, wire or
similar objects as this may damage the
sweeping mechanism.
The height of the roller brush is adjusted via
a rotary knob. The height must be selected
so that the bristles just touch the ground.
Note: An adjustment that is too low leads to
overstraining the drives and unnecessary
wear of the roller brush without achieving a
better sweeping result.
Turning in (–) direction: Roller brush ris-
es.
Turning in (+) direction: Roller brush is
lowered.
In order to sweep the dirt to the side, the
roller brush can be swivelled to the left or
right.
This is also a benefit for removing snow by
means of the snow removal shield upgrade
kit.
Tilt the swivel bracket forwards until the
notch is free.
Swivel to the left or right, depending on
which side you wish to sweep the dirt to.
Tilt swivel bracket backwards and snap
into place.
Release parking brake.
Pull clutch lever for travel drive.
Note: The driving speed is fixed and
cannot be modified.
Release clutch lever for travel drive.
Device comes to a halt.
Pull the lever for the roller brush drive,
roller brush is turning.
Release the lever for roller brush drive.
Roller brush comes to a halt.
Release clutch lever for roller brush
drive and travel drive.
Gas lever to "OFF" position.
Close the fuel supply.
Turn the rotating knob perpendicular to
the fuel tap.
Activate parking brake.
DANGER
Risk of personal injury or damage!
Observe the weight of the appliance
when you load it!
Switch off engine.
Empty fuel tank.
Parking brake
Before Startup
Unloading
Fold up and install the push handle
Start up
Refuelling
1
2
Prior to start/safety test
Maintenance Works
Operation
Starting the machine
Sweeping mode
Height adjustment roller brush
Angle adjustment roller brush
Driving operations
Roller brush drive
Turn off the appliance
Transport
12 EN
Loading ...
Loading ...
Loading ...