LX6000A
AIR COOLING CONTINUOUS
INDUCTION SEALING MACHINE
(*Read this manual carefully before use)
(*Please safekeeping of the instructions)
PRODUCT MANUAL
- 1 -
1. Summary
This machine applies to aluminum foil sealing of non-metal
bottles of plastic or glass in pharmacy, chemical, food, drink,
cosmetic area.
2. Working principle
This machine applies the principle of electromagnet induction heating.
Through non-contact inductive heating, both the inductive film and aluminum
film compound film will be tightly stuck onto the opening of the sealing
object(or cup)after instantly thermal melting so as to reach the target of
seal.
3.Main technical parameters
- 2 -
1、Input power：AC220V±10%，50/60Hz
2、Input electrical current：＜10A
3、Output electrical current：static state＜2A，dynamic state＜10A
4、Working frequency：75～85KHz
5、Output power：≤1200W
6、Protection degrees：IP21
7、Sealing diameter：￠20mm～￠80mm
8、Height of bottle：20～300mm
9、Sealing speed：0～10M/min（PS：Because of the bottle materiel or the
mouth of bottle diameter, sealing speed will be a little different. We use
a bottle made by PE , the diameter is ￠33mm for test, the speed is 200 bottle
per minute.）
10、Total maximum load weight：≤3Kg
11、Shell：Stainless steels
12、Size：1120X470X590mm
4.Attention：
1、Let machine working on a balanced place，ground connection（Ground
connection can not use three-pin-plug directly, should use another
ground wires, for safe），then turn on the power switch。
2、Power line and grounding line cross section areas should not less than
1mm
2
.When power supply is instability (input voltage over than 240V or less
than 200V)，you should set an automatic alternate voltage stabilizer, for
protecting sealing effort and machine.
3、Please keep machine working in a dry, clean and ventilated place, and
keep away from any heating source.Attention：if machine working in damp or
strong acid-base for long time, it will cut the machine life-time.
4、This machine is suit for sealing plastic, glass, paper, etc ,it could
not using with metal bottle.
- 3 -
5、Material of induction film should be same as bottle, the thickness
of induction aluminum foil can be 0.015~0.03mm, we advice not using
vacuum coating aluminum foil, or it may not sealing well.
6.Operation：
1、Connecting 220V power supplies, turn on power switch, when line
voltmeter show input voltage, air cooling start working.
2、According to bottle height and size, adjusting bottle with induction
head space distance(small bottle:2~5mm, big bottle:10mm) and width of
leading fences.
3、According to bottle diameter, preliminary adjustment for suitable
sealing speed. Eg: small bottle, space distance should be short, the speed
should be slow. Big bottle, space distance should be wide, the speed should
be quick.
4、Turn on the induction switch, set the aluminum induction foil(aluminum
foil face to bottle mouth, paper side face to bottle cover).Then tight the
bottle cover, put bottle on deliver tape, and test, attention on point
2 and 3. When it over working, check the sealing effort, until the parameter
can let your product sealing well.
5、Please note the best parameter for your bottle. After setting, when
it is working, you can touch the bottle cover, if it was warm or not,
when you could not feel warm, stopping machine and check, find problem,
and deal with it. Do not let unsealed bottle mix with sealed bottle.
6、When equipment main circuit be hot, overheating protection function
will open, equipment stop working automatic, until temperature reduce to
normal, machine will start working again.
7, Packing list：
NO
NAME
MODEL
QUATITY
- 4 -
1
Machine
LX-6000
1
2
Power line
0.75mm
1
3
Protective tube
10A
2
4
Hex socket handle
Opposite side 6mm
1
5
Hex socket handle
Opposite side 4mm
1
6
Wood screw
（cross）
1
7
manual
1
8
Testing bottle
Diameter 40mm
5
Remark: These are machine essential parts, if need another machine
accessories, you can ordered.
Product
No
DATE
Y M D
