Loading ...
Loading ...
Loading ...
Operation of Your Opener
Activate the opener with any of the following:
• The Remote Control: Hold push button down until
the door starts to move.
• The Door Control: Hold push button down until the
door starts to move.
• The Outdoor Key Switch or Keyless Entry.
(See Accessories)
When the opener is activated with the safety
reversing sensor installed and correctly aligned:
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3: If opening, the door will stop (allowing space for
entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse.
6. tf obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle,
and the opener lights will blink for 5 seconds, when
the invisible beam is broken. Iffully open, the door
wil! not close when the beam is broken. The sensor
has no effect in the opening cycle.
If the sensor is not installed or not aligned correctly,
the door won't close from any remote control. You
can close the door with the Door Control, the
Outdoor Kay Switch, or Keyless Entry, however, if
you activate them untildown travelis complete. If
you release them too soon, the door will reverse.
The Opener Lights will turn on under the following
conditions: When the opener is initially plugged in;
when the power is interrupted; when the opener is
activated. It will turn off automatically after 4-1/2
minutes or provide constant light when the Light
feature on the Premium Control Console is activated.
Bulb size is 75 watts maximum.
SECURITY+ models: Lights will also turn on when
someone walks through the open garage door. With
a Premium Control Console, this feature may be
turned off as follows: With the opener lights off, press
and hold the light button for 10 seconds, until the
light goes on and off again. To restore this feature,
start with the opener lights on, then press and hold
the light button for 10 seconds.
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible, use the emergency
release rope and handle onlywhen the door is
fully closed.
rrn
Emergency
Release Handle
(Pull Down)
Manual disconnect
position
To open the door
manually:
The door should be fully
closed if possible. Pull
down on the red
emergency release
handle and lift the door
manually. To reconnect
the door to the opener,
press the Door Control
push button.
Trolley _1_
Emergency
The lockout feature
prevents the trolley from
reconnecting auto-
matically. Pull the
emergency handle down
and back (toward the
opener). The door can
then be raised and
lowered manually as
often as necessary. To
Release Handle •
(Pull Down & Back disengage the lockout
TowardsOpener)feature, pull the
Lockout position emergency handle
straight down. The trolley
will reconnect on the next
UP or DOWN operation.
Operation of the Door Controls
(SECURITY+ models: See additional programming features, next page,)
Press the lighted push button to open or close the
door.
Press again to reversethe door during the closing
cycle or to stopthe door while it's opening.
Premium Console:
Lightfeature:Press the large round Light button. If
the opener light is off, it will turn on. If the opener
light is on, (even in the 4-1/2 minute automatic
cycle) it will turn off.
But if you use the Light button to turn the lights on
and then activate the opener, the lights will turn off
after 4-1/2 minutes.
The Light button will not control the opener lights
when the door is in motion.
Premium Console (cont.):
Lock feature: The Lock feature is designed to
prevent operation of the door from remote controls.
However, the door will open and close from the
Door Control, the Outdoor Key Switch and the
Keyless Entry Accessories.
To activate: Press and hold the small round Lock
button for 2 seconds. The push button light wilt
flash as long as the Lock feature is on.
To turn off" Press and hold the Lock button again
for 2 seconds.The push button light will stop
flashing. The Lock feature will also turn off
whenever the SRT button on the opener panel is
activated.
32
Loading ...
Loading ...
Loading ...