Loading ...
Loading ...
Loading ...
16
17
Owner’s Manual
Owner’s Manual
CONTROL PANEL (CONTINUED)
Quick Start:
1. After you turn the unit on, press “start” on the dial. “375F” and “TEMP”
will be displayed and the countdown will begin.
• The Wok is defaulted to 375F for 20 minutes.
Temperature Function:
Simply turn the dial to decrease or increase temperature.
• Located on the left dial.
• Temperature range 100-575F in 5-degree increments.
Time Function:
Simply turn the dial to decrease or increase time.
• Located on the right dial.
• Time range is from 1 minute to 9 hours and 59 minutes (Time is in Hours
and Minutes).
Stage Function:
1. Press “stage”. “STAGE” will be ashing and “1”, “TIME”, and “00:00” will
be displayed.
2. Set time and adjust temperature, if needed.
3. Press “stage” again. “STAGE” will be ashing and “2”, and “TIME”, and
“00:00” will be displayed.
4. Set time and adjust temperature, if needed.
5. Repeat steps, if necessary.
• You can create up to 10 stages. Stage 10 will display as “0”.
6. Press “start”.
Preheat Function:
1. Press “preheat”. “PREHEAT” and “375F” will be displayed.
2. Adjust time and adjust temperature, if needed.
• Preheat program has a default of 375F for 20 minutes.
3. Press “start”. Selected temperature and “F” will be ashing.
4. Once the temperature you selected has been reached, “selected
temperature” and “ready” will be displayed indicating the Wok will hold
that temperature for 5 minutes or until you press “start”.
5. Once you press “start”, the countdown you selected will begin with the
programmed temperature.
• If you press “pause” when the unit is preheating, “5” will be ashing,
indicating the Wok will hold the program for 5 minutes or until you
press “start”.
TROUBLESHOOTING GUIDE
• When any of the above error messages displays on the LED, the unit will
“beep” at least once.
• The fan will run up to a maximum of 60 seconds after pressing “pause/
clear” once. Continue cooking by pressing “start” within 45 minutes.
• The unit will turn off after 45 minutes if no buttons (such as “start”) are
pressed. When the unit shuts off, it will clear all previous cooking history.
• After pressing “pause/clear” twice or cooking has stopped, the fan will
run up to a maximum of 60 seconds until the unit cools. At that point, the
NuWave Precision Induction Wok will turn off.
Error Message Solution
E1
E2 The unit is malfunctioning. Contact customer service.
E3 The unit’s voltage is too low. Minimum = 85 volts
E4 The unit’s voltage is too high. Maximum = 144 volts
E5 The unit is malfunctioning. Contact Customer Service.
E6 The unit is malfunctioning. Contact Customer Service.
E7
Overheating or air ventilation is obstructed. If internal
temperature exceeds 230˚F, operation will cease and a
“beep” noise will be produced. Press “pause/clear” twice.
Wait for the unit to cool.
E8
Overheating or if unit exceeds a temperature 20˚F
higher than sear, the appliance will turn off. Contact
Customer Service.
E9
The unit is malfunctioning. Contact Customer Service at
1-877-689-2838 or help@nuwavenow.com.
FULL
In programming mode, when the total entered time
reaches the appliance’s limit of 99:59, no additional
stages can be inputted.
An E1 reading typically means that your NuWave
Precision Induction Wok
™
does not detect Wok on its
surface. This can occur for one of two reasons:
1. The induction coils contained within the
NuWave Precision Induction Wok will only
work when they are in direct contact with a
piece of Wok. To maintain your appliance’s
effectiveness, always ensure that it rests on a
at surface and that contact is consistent with
your Wok.
2. An E1 message may also occur if your Wok is
not induction-ready.
It is recommended to only use supplied
Wok with the Precision Induction Base.
Loading ...
Loading ...
Loading ...