Loading ...
Loading ...
Loading ...
en Before using for the first time
12
Malfunctions may occur when using filtered or deminer-
alised water. The appliance may request that you top
up the water tank even though it may be full, or opera-
tion with steam is cancelled after approx. twominutes.
▶ If required, mix filtered or demineralised water with
the bottled non-carbonated mineral water with a ra-
tio of onetoone.
Tip:If you use mineral water, set the water hardness
range to "very hard". If you use mineral water, you must
only use non-carbonated mineral water.
Tip:If your tap water is very hard, we recommend that
you use softened water. If you use only softened water,
you can set your appliance to the "softened" water
hardness range.
Setting Water hardness in
mmol/l
German hardness in
°dH
French hardness °fH
0 (softened)
1
- - -
1 (soft) Up to 1.5 Up to 8.4 Up to 15
2 (moderately hard) 1.5-2.5 8.4-14 15-25
3 (hard) 2.5-3.8 14-21.3 25-38
4 (very hard)
2
Above 3.8 Above 21.3 Above 38
1
Only set this if you will be using solely softened water.
2
Also set for mineral water. Only use non-carbonated mineral water.
6.2 Initial use
When the appliance is connected to the power supply
for the first time or following a lengthy power failure, the
settings that you will need to configure before you can
use it will appear.
Note:You can change these settings at any time by
going to the basic settings.
→"Basic settings", Page24
Setting the language
1.
Connect the appliance to the power supply.
a The first setting will appear after a few seconds.
2.
Press the bottom row.
3.
Swipe left or right to select the required language.
4.
Press the top row.
Setting the time
1.
Press "Time".
2.
Press the bottom row.
3.
Swipe left or right to select the correct hour.
4.
Press "Minutes".
5.
Swipe left or right to select the correct number of
minutes.
6.
Use the
button to save your settings.
Setting the date
1.
Press "Date".
2.
Press the bottom row.
3.
Swipe left or right to select the correct day.
4.
Press "Month".
5.
Swipe left or right to select the correct month.
6.
Press "Year".
7.
Swipe left or right to select the correct year.
8.
Use the
button to save your settings.
Setting the water hardness
1.
Press "Water hardness".
2.
Swipe left or right to select the appropriate water
hardness.
→"Before using for the first time", Page11
3.
Use the
button to finalise the initial configuration
process.
4.
Open and close the appliance door once.
a The appliance will perform a self-test, after which it
will be ready to use.
a Initial configuration is now complete.
6.3 Calibrating and cleaning the appliance
You will need to calibrate the appliance and clean the
cooking compartment and accessories before using it
to cook food for the first time.
Note:The boiling point of water depends on the air
pressure. During the calibration process, the appliance
makes adjustments to adapt it to the pressure condi-
tions in the location where it is installed.
Requirement:The cooking compartment must have
cooled down completely.
1.
Remove the product information, accessories and
any leftover packaging (e.g. polystyrene pellets)
from the cooking compartment.
2.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
3.
Press
to switch the appliance on.
→"Switching on the appliance", Page13
4.
Fill the water tank.
→"Filling the water tank", Page14
5.
Set the required type of heating, temperature and
cooking time for the calibration process and press
to start.
→"Steam", Page15
Calibration
Type of heating Steam
Temperature 100 °C
Duration 30minutes
Tip:Do not open the appliance door while calibra-
tion is in progress. Calibration will otherwise be in-
terrupted.
a Calibration starts. This generates a lot of steam.
Loading ...
Loading ...
Loading ...