Loading ...
Loading ...
Loading ...
Grounding instructions
WARNING 1
I II
IMPROPER GROUNDING CAN RESULT IN
ELECTRICAL SHOCK. IN THE EVENT OF A
SHORT CIRCUIT, GROUNDING REDUCES
THE RISK OF SHOCK BY PROVIDING AN
ESCAPE WIRE FOR THE ELECTRIC CUR-
RENT. THIS AIR COMPRESSOR MUST BE
PROPERLY GROUNDED.
1. The air compressor isequipped with a cord having a
grounding wire and an appropriate grounding plug.
The plug must be used with an outlet that has been
installed and grounded in accordance with all local
codes and ordinances. The outlet must have the
same configuration as the plug. DO NOT USE AN
ADAPTER.
2. Do not modify the plug that has been provided, If it
does not fit the available outlet, the correct outlet
should be installed by a qualified electrician.
3. Inspect the plug and cord before each use. Do not use
if there are signs of damage.
ELECTRICAL SHOCK HAZARD. WHEN
REPAIRING OR REPLACING THE CORD OR
PLUG, KEEP THE GROUNDING WIRE SEPA-
RATE FROM THE CURRENT-CARRYING
WIRES. NEVER CONNECT THE GROUND-
ING WIRE TO A FLAT BLADE PLUG TER-
MINAL. (THE GROUNDING WIRE HAS
INSULATION WITH AN OUTER SURFACE
THAT IS GREEN - WITH OR WITHOUT YEL-
LOW STRIPES.)
If these grounding instructions are not completely
understood, or if you are not sure your compressor is
properly grounded, have the installation checked by a
qualified electrician.
PLUG OUTLET
GROUND
240 VOLT, 20 AMP PLUG
GROUNDINGJ
PiN
OUTLET
Break-in Procedures
Serious damage may result if the following
break-in instructions are not closely
followed.
This procedure is required only once, before the air com-
pressor is put into service.
!. Set the pressure switch lever to the "OFF" position.
2. Plug the power cord into the correct branch circuit
receptacle,
3. Open the shut-off valve, turn it counterclockwise to
open, opening it fully, to prevent air pressure build-up
in the tank,
4. Move the pressure switch lever to "ON/AUTO". ThE
compressor will start.
5. Run the compressor for 30 minutes. Make sure the
shut-off valve is open and there is no tank pressur(
build-up,
6. After 30 minutes, close the shut-off valve by turnin(.
the knob clockwise. The air receiver will fill to cut-ou
pressure and the motor will stop. The compressor i:
now ready for use.
OPERATING PROCEDURES
1.Before attaching an air hose or accessory, make sure
the pressure switch lever is in the "OFF" position.
Close the shut-off valve by turning the knob
clockwise.
2. Attach hose and accessory.
WARNING
IIII
TOO MUCH AIR PRESSURE CAUSES A
HAZARDOUS RISK OF BURSTING. CARE-
FULLY FOLLOW STEPS 3 THROUGH 11
EACH TIME THE COMPRESSOR IS USED.
3. Check the manufactur's maximum pressure rating for
air tools and accessories. The regulator outlet pres-
sure must never exceed the maximum pressure rat-
ing. On this model, a regulator must be installed
before using accessories rated at less than 125
psig.
Compressed air from the outfit may contain
water condensation and oil mist, Do not
spray unfiltered air at an item that could be
damaged. Some air operated tools or
devices may require filtered air. Read the
instructions for the air tool or device.
4. Turn the pressure switch lever to the "ON-AUTO" posi
tion and allow tank pressure to build. The motor wil
stop when tank pressure reaches cut-out pressure.
5. Open the shut-off valve. Your outfit is ready for use.
When You Are Finished:
6. Set the pressure switch lever to "OFR"
7, Close the shut-off valve.
8. Remove the air tool or accessory.
9. Open the shut-off valve and allow the air to slow
bleed from the tank. Close the shut-off valve wh_
tank pressure is approximately 20 psi.
Loading ...
Loading ...
Loading ...