• Theseinstructionsareaguideonly.Forcompleteinstallation
instructions,refertothemanualprovidedwiththeproduct.
• Ifyoudonotfollowtheinstallationinstructionsyour
dishwasherwillnotbeproperlyinstalled.Theproduct
warrantydoesnotcoverincompleteorimproper
installation.Youwillbechargedaservicefeeforany
servicecalltorectifyimproperorincompleteinstallation.
• Theseinstructionsapplytofreestandingapplicationsonly.
• Ifyourdishwasheristtedwithawaterinlethosewithsafety
valve,youwillneedanopeningofatleast45mmx90mm
inyourcupboardsinordertofeedthehosethroughit.
Thedimensionsshownbelowareinmillimetres.Theheightof
850mmiswiththelevellinglegsscrewedinattheminimumheight.
Thedimensionsshownbelowareinmillimetres.Theopening
allowsforsomeclearancesothatthedishwashercanbe
pushedintoplace.
Note: if the opening is greater than 600mm wide then a
suitable width filler piece should be secured to the cupboard
before installing the dishwasher.
Puttheapplianceadjacenttoawatertapandawaterdrain.
Theplinthofafreestandingapplianceisnotadjustable.Do
notremovetheappliance’sworktopifyouwanttouseitas
afreestandingunit.Itisnotnecessarytoremovetheworktop
wheninstallingunderastandardkitchenbenchtop.Only
removetheapplianceworktoptoinstallunderaclosetting
sinkunitorkitchenworktop(820mm).
Makesurethatthedimensionsoftherecessagreewiththe
givendimensions.
1.Removetherearscrews.
2.Pulltheworktopbehindtheappliance.
3.Lifttheworktopandmoveitfromthefrontslots.
4.Levelofftheapplianceusingtheadjustablefeet.
5.Installtheapplianceunderthekitchenworktopensuringthat
waterhosesarenotkinkedorsquashed.
Theappliancemustbeeasilyaccessibletoatechnicianif
repairisnecessary.
WDF901SA, WDF901WA, WDF902SA, WDF902WA
850mm
820mm
620mm
centre of
control
panel
180mm
50mm
100mm
596mm
555mm edge of door
585mm centre of door
585mm
600mm
Do not install taps or
power points in this space
855mm min.
8
with worktop
825mm min.
830mm max.
without worktop
60mm max.
Gap on both sides
should be equal and no greater
than 3mm per side
If floor is not level, adjust
levelling legs to suit
600mm max -
300mm min
POWER SUPPLY
230/240V–10Amps
TAP CONNECTION
If cold-water pressure is
in excess of 800kPa, a
pressure-reducing valve
should be used.
Check for leaks.
INLET WATER SUPPLY
Water flow rate 10L/minute min
Water temperature 60
o
C max
Water pressure cold water:
800kPa max - 50kPa min
Water pressure hot water:
350kPa max - 50kPa min
Cold water recommended
The hose should not be
extended by more than
2 metres or water pump-out
problems may occur
There should be a minimum
2mm gap between the top of
the dishwasher and
underside of bench top
Fix drain hose max of
10mm below the top of
the dishwasher
Remove entire plastic
membrane from sink trap
spigot & fit drain hose to
spigot with clamp
DISHWASHER
POWER OUTLET
SINK
1000mm max
IMPORTA NT
850mm
820mm
620mm
centre of
control
panel
180mm
50mm
100mm
596mm
555mm edge of door
585mm centre of door
585mm
600mm
Do not install taps or
power points in this space
855mm min.
8
with worktop
825mm min.
830mm max.
without worktop
60mm max.
Gap on both sides
should be equal and no greater
than 3mm per side
If floor is not level, adjust
levelling legs to suit
600mm max -
300mm min
POWER SUPPLY
230/240V–10Amps
TAP CONNECTION
If cold-water pressure is
in excess of 800kPa, a
pressure-reducing valve
should be used.
Check for leaks.
INLET WATER SUPPLY
Water flow rate 10L/minute min
Water temperature 60
o
C max
Water pressure cold water:
800kPa max - 50kPa min
Water pressure hot water:
350kPa max - 50kPa min
Cold water recommended
The hose should not be
extended by more than
2 metres or water pump-out
problems may occur
There should be a minimum
2mm gap between the top of
the dishwasher and
underside of bench top
Fix drain hose max of
10mm below the top of
the dishwasher
Remove entire plastic
membrane from sink trap
spigot & fit drain hose to
spigot with clamp
DISHWASHER
POWER OUTLET
SINK
1000mm max
IMPORTA NT
Loading ...
Loading ...
