Loading ...
Loading ...
Loading ...
Toapplydetergentfollowthesedope:
1. ReviewProjectProTM nozzleand HydroFoamTM launcheruse.
2. PrepareHydroFoamTM wash according to instructions on
the bottb or prepare detergentsolution as required by job.
3. Mace smaii fiiter end of detergent siphoning tube into
detergent container.
NOTE:Make sure the filter is fully submerged in detergent
while applying detergent.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
Wheninsertingthefilterintoadetergentsolutionbottb,routethe
tubesoasto keepitfrom inadvertentlycontactingthehot rnuffler.
4. Make sure HyrdoFoamTM Launcher is installed.
NOTE:Detergentcannot be appiied with the high pressure
nozzles (Yellow, Orange or Red).
5. Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
6. Start engine foilowing instructions How to Start Your
Pressure Washer.
Ye--re ,(7u start the enqine. _
Starting the engine without a!l the hoses connected and without
the water turned ON will damage tbe pump.
Darnageto equipment resulting from failure to follow this
instructionwill void warranty.
7. Appiy HydroFoamTM wash to a dry surface, starting at
lower portion of area to be washed and work upward,
using iong, even, overlapping strokes.
NOTE:To prevent water spotting on vehicles,work in a
shaded areaand allow surfacesto cool before beginning.
8. Aliow HydroFoamTM wash to soak in between
3-5 minutes before washing and rinsing. Reappiyas
neededto prevent surface from drying. DO NOTaliow
HydroFoamTM wash to dry on (prevents streaking).
Forbest results, scrub the HydroFoamTM wash covered
surface to heip remove stubborn dirt, grime and stains. For
vehicles, use a soft car wash brush or mitt. For decking,
siding and concrete, use a brush appropriate for the type of
surface being cleaned.
IMPORTANT:You must flush the detergentsiphoning system
after each use by placingthe fiiter into a bucket of clean water,
then run the pressurewasherin low pressurefor 1-2 minutes.
Pressure Washer Rinsing
_,fterNydroFeamTM washis applied, seeer the eeffaee andrinse
it clean as fellows:
1. Remove HyrdoFoamTM Launcher from nozzleextension.
2. Selectand install desired ProjectProTM nozzle,as
described in How to UseProjeetProTMNozzleSystem.
3. Keepspray gun a safe distance from spray surface.
WARNING
Kickbackfrom spray gun can causeyou to fail.
o Operatepressurewasherfrom astablesurface.
o Beextrerne[ycarefulif you mustusetbe pressurewasberfrom
a ladder,scaffolding,or anyotbersimilarlocation.
• Firmlygraspspraygunwithboth handswbenusing high
pressuresprayto avoidiniurywhenspraygun kicksback.
4. Apply a high pressure spray to a smaiI area and then
check the surface for damage.If no damage,proceed to
step 5.
Start at top of areato be rinsed, working down with
same overlapping strokes used for cleaning.
Cteaning getergent $iphening Tehe
If you used the detergentsiphoning tube, you must flush it
with ciean water before stopping the engine.
1. Piacedetergent siphoning tube/filter in a bucket full of
clean water.
.
3.
.
5.
Remove high pressure nozzlefrom nozzleextension.
Seiectand instali btack detergent nozzle foliowing
instructions How to UseProjeetProTMNozz/'eSystem.
Flushfor 1-2 minutes.
Shut off engine foliowing instructions How to Stop
Pressure Washerand turn off water supply.
6. ALWAYS point spray gun in a safe direction, press red
button and squeezespray gun trigger to release retained
high water pressure.
iMPORTANT:Spray gun traps high water pressure, even
when engine is stopped and water is disconnected.
WARNING
The high pressurestream of water that this
equipment produces can cut through skin and its
underlying tissues, ieadingto serious injupj and
_ossibleamputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.
o Keephighpressurehoseconnectedto pumpandspraygun
whilesystemis pressurized.
• ALWAYSpointspraygun insafedirection,pressred button
andsqueezespraygun trigger,to releasehigh pressure,every
timeyoustop engine.
Automatic Ceel gown System {Thermal Relief}
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray guls,
circulating water in the pump can reach temperatures above
125°F. The system engagesto cool the pump by discharging
the warm water onto the groend.
15
Loading ...
Loading ...
Loading ...