Loading ...
Loading ...
Loading ...
42
Nuestros tractores cumplen con los estándares de seguridad del
American National Standard Institute.
(A) PALANCA DEL LEVANTAMIENTO DEL AC-
CESORIO - Se usa para levantar, bajar y ajustar
el conjunto segador o los demás ac ce so rios
montados en su tractor.
(B) PEDAL DEL EMBRAGUE/FRENO - Se usa
para desembragar y frenar el tractor y para hacer
arrancar el motor.
(C) PALANCA DEL FRENO DE ESTACIONA-
MIENTO - Ase gu ra el pedal del embrague/freno
en la posición del freno.
(D) CONTROL DE ACELERACIÓN/ESTRAN-
GULACIÓN - Se usa para hacer arrancar y
controlar la velocidad del motor.
(E) PALANCA DEL EMBRAGUE DEL AC-
CESORIO - Se usa para enganchar las cuchillas
segadoras, o los demás ac ce so rios montados
en su tractor.
(F) INTERRUPTOR DE IGNICIÓN - Se usa para
hacer arrancar o hacer parar el motor.
(G) SISTEMA DE FUNCIONAMIENTO HACIA
ATRÁS (ROS) EN POSICIÓN “ON” - Permite la
operación del conjunto segador o otro accesorio
accionado mientras que en revés.
(H) INTERRUPTOR DE LA LUZ - Enciende y
apaga las luces de lan te ras.
(J) PALANCA DE CONTROL DE MOVIMIENTO -
Selecciona la velocidad y la dirección del tractor.
(M) CONTROL DE RUEDA LIBRE - Desengan-
cha la trans-misión para empujar o arrastrar.
FAMILIARICESE CON SU TRACTOR
LEA ESTE MANUAL DEL Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR
Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos
controles y ajustes. Guarde este manual para referencia en el futuro.
E
A
B
C
H
G
D
M
J
F
27
TO REPLACE HEADLIGHT BULB
1. Raise hood.
2. Remove bulb hold er from the hole in the
back side of the grill.
3. Replace bulb in holder and install bulb
holder securely back into the hole in the
backside of the grill.
4. Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your
tractor to run poorly, stop running, or prevent
it from starting.
• Check wiring.
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-
in fuse. The fuse holder is located behind
the dash.
TRANSMISSION REMOVAL/
RE PLACE MENT
Should your transmission require re mov al for
service or re place ment, it should be purged
after reinstallation and before operating the
tractor. See “PURGE TRANS MIS SION” in
the Operation sec tion of this manual.
ENGINE
TO AD JUST THROTTLE CON TROL
CABLE
The throttle control has been preset at
the factory and ad just ment should not be
necessary Check adjustment as described
below before loosening cable. If adjustment
is nec es sary, see engine manual.
TO AD JUST CHOKE CON TROL
The choke control has been preset at the
factory and ad just ment should not be neces-
sary. If adjustment is necessary, see engine
manual.
TO REMOVE HOOD & GRILL AS SEM BLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Remove retainer clip and washer from
right hand pivot pin.
4. Stand in front of tractor. Grasp hood at
sides and slide left removing hood from
pivot pins and lift hood off of tractor.
5. When replacing hood, reconnect the
headlight wire con nec tor, and reinstall
the washer and retainer clip on the
right hand pivot pin.
04031
Hood
Left Pivot Pin
Washer
Retainer
Clip
Right Pivot
Pin
Headlight Wire
Connector
Loading ...
Loading ...
Loading ...