Loading ...
Loading ...
Loading ...
38 39
INSTALLATIONINSTALLATION
Hard Wiring Detail
1. Remove terminal cover plate from rear panel
of appliance.
2.fitwiresthroughholeincoverplateandmake
connections to terminals.
3.engagewiresintoplasticclip.Secureplasticclipwith
two long silver screws (supplied in separate bag).
4.Replacecoverplateontorearpanel.
Oven Dimensions
A
Underbenchoven595mm
SeparateGrillUnderbenchoven725mm
Separate Grill Wall Oven 888mm
Duooven888mm
Doubleoven1083mm
Allbuilt-inovensare596mmwide
Plastic clip
securing points.
Plastic clips
Second active wire only
required (optional) for
multi-phase products.
WARNING
USE AN AUTHORISED PERSON
Asstatedinthelocalmunicipalbuildingcodesandother
relevant statutory regulations.
•Wiringconnectionsmustbeinaccordancewith
AS/NZS3000WiringRulesandanyparticular
conditions of the local authority.
•Refertodataplateforratinginformationandcircuit
diagram. The data plate is positioned behind the
bottom of the oven door. The circuit diagram is
positioned on the top panel of the appliance.
•forapplianceswithopencookingsurfaces,anallpole
disconnect functional switch should be provided near
the appliance in an accessible position. Refer to
AS/NZS3000clause4.7.1
•Wiringshouldbeprotectedagainstmechanicalfailure.
RefertoAS/NZS3000clauses3.3.2.6,3.9,3.10
•Ameansofdisconnectionwithacontactseparation
ofatleast3mmmustbesuppliedinthefixedwiring.
• Togainaccesstothemainsconnectionterminals,remove
therearaccesscoverbyunscrewingthe2screws.
MULTI-PHASE: Where connection is made to a multi-phase 240V supply,
the bridge piece should be removed from between the active connections.
WARNING
This appliance must be properly earthed.
•Donotlifttheappliancebythedoorhandles.
•Preparethecupboardopeningtomatchyour
appliance measurements. (See diagrams).
•Slideapplianceintothecupboard,ensuringthatthe
supply cable (where fitted) does not kink.
• Topreventtipping,usethescrewssuppliedtosecureyour
ovenintothecupboard.Usejust2screwsforsingle
cavityovensand4screwsfordualcavity.Removethe
bottom door in dual cavity ovens to provide access to the
bottom2screwingpoints(seeillustrationonpage32).
•forappliancesfittedwithaflexiblesupplycord,ifthe
cord is damaged, it must be replaced by the manufacturer
or its service agent or similarly qualified person in order to
avoid a hazard. The plug must be accessible after installation.
• Wheretheapplianceisbuiltintoacabinet,thecabinet
materialmustbecapableofwithstanding70°C.
Installation into low temperature tolerant cabinetry
(e.g. vinyl coated) may result in deterioration of the
low temperature coating by discolouring or bubbling.
•Iftheapplianceisinstalledadjacenttovinyl-wrapped
surfaces,useaninstallationkitavailablefromthevinyl-
wrap supplier.
•electroluxHomeProductscannotacceptresponsibility
for damage caused by installation into low temperature
tolerant cabinets.
•Afterinstallation,testandensurethattheappliance
operates correctly before handing it over to the customer.
To avoid any potential hazard, you must follow our instructions
below when you install your appliance. Failure to install the
appliance correctly could invalidate any warranty or liability
claims and lead to prosecution.
Cabinet Construction for your appliance
For the best integration within a kitchen, install this appliance
inastandard600mmwidecupboardthatgivesaflush fit
withthesurroundingcupboardfronts(figureA).
Arecessof20mmisideal.Itcanalsobeinstalledusing
aproudfitwiththesurroundingcupboard(figureB).
NOTE: Your appliance must be mounted on a flat surface
for the full width and depth of the product.
CAUTION
TheinfillpanelmUSTnotexceed100mminliengthto
ensurea16mmgapismaintained.
Flush Fit
16mm
568mm
600mm
20mm
Infill
panel
Cupboard
door
Oven
100mm
max for
Pyro oven
Proud Fit
16mm
568mm
600mm
Infill
panel
Cupboard
door
Oven
100mm
max for
Pyro oven
INSTALLING YOUR APPLIANCE
Loading ...
Loading ...
Loading ...