ODVILLA36T User Manual

Loading ...

20 ft (6.10 m) max.

pipe between an

offset & return

Ceiling Firestop

35 ft (10.67 m)

max. straight

unsupported

chimney height

14.5 ft (4.42 m) min. height/single offset-return

20 ft. (6.1 m) min. height/double offset-return

90 ft (27.43 m) max. height

6 ft (1.83 m) max.

unsupported chimney

above roof

39 1/2 in. (1003 mm)

Effective Height

Figure 8.2 Chimney Requirements

Determinethechimneycomponentsneededtocomplete

yourparticularinstallation:

• Measure the total vertical height of the fireplace

installationfromthebaseofthereplaceassemblyto

theapproximatelocationofthebottomofthetermination

cap.

• Subtracttheeffectiveheightofthereplaceassembly

(seeFigure8.2)fromthetotalverticalheighttodetermine

theoverallheightofthechimneyinstallation.

• CreateaschematicforyourapplicationsimilartoFigure

8.2 showing components required (referring to Table

8.1).Figure8.1identiesthosecomponentsandwhere

used.

• Installaceilingrestopwheneverthechimneypenetrates

aoor/ceiling.

NOTICE: A maximum of two pairs of offsets and returns

may be used.

CAUTION! Risk of Fire and/or Asphyxiation! DO

NOT connect this replace to a chimney ue servicing

another appliance. DO NOT connect to any air distribu-

tion duct or system. These actions could cause over-

heating/re in the chimney ue, or release of exhaust

fumes into the living areas.

ft m

• Minimumheightwithoffset/return 14.5 4.42

•

Maximumheight 90 27.43

• Maximumchimneylengthbetweenanoffset

and return

20 6.1

• Maximumdistancebetweenchimney

stabilizers

35 10.67

• Doubleoffset/returnminimumheight 24 7.32

• Maximumunsupportedchimneylength

betweentheoffsetandreturn

6 1.83

• Maximumunsupportedchimneyheightabove

thereplace

35 10.67

• Minimumoverallstraightheightifreplaceis

freestanding

6.4 1.95

• MinimumStraightHeight 14.5 4.42

A. Chimney Requirements

Whenplanningyourreplacelocation,thechimneycon-

structionandnecessaryclearancesmustbeconsidered.

Thereplacesystemandchimneycomponentshave

beentestedtoprovideexibilityinconstruction.Thefol-

lowingguresaretheminimumdistancesfromthebase

ofthereplace.

• Minimum overall straight height is 6 ft 4 in. if the

replaceisfreestandingandaminimumof10ftfroma

combustiblestructure. SeeFigure3.2.

• Chimneymustextend2ft(.6m)aboveanyportionofthe

roofwithin10ft(3m)ofthechimney.RefertoFigure6.1.

Table 8.1

HEIGHT OF CHIMNEY COMPONENTS in. mm

Chimney Stabilizer

SL3 4-3/4 121

Ceiling Firestops

FS338 0 0

FS339 0 0

FS340 0 0

Offsets/Returns

SL315 13-3/8 340

SL330 15-1/2 394

Roof Flashing

RF370 0 0

RF371 0 0

Chimney Sections*

SL306 4-3/4 121

SL312 10-3/4 273

SL318 16-3/4 425

SL324 22-3/4 578

SL336 34-3/4 883

SL348 46-3/4 1187

* Dimensions reect effective height.

OutdoorLifestylesbyHearth&HomeTechnologiesInc.•4072-137RevK•10/15

Loading ...

User Manual - Page 24