Loading ...
Loading ...
Loading ...
Lighting Grill Burners with Flash Tubes
Place the lit match through the grid next to the flash tube of
the burner being lit. Keep your face as far away from the grill
as possible. Make sure the match is adjacent to the flash
tube. Push and turn the control knob until the “HIGH”
position on the knob aligns with the indicator line on the
control panel. Make sure you are turning the control knob
that corresponds with the burner being lit. If the burner
does not light in 4 seconds, turn the knob to “OFF,” wait
five minutes, and try again. If the burner will not light after
several attempts, see the Troubleshooting section.
Lighting TruSear™ Infrared Burner (If Applicable)
Push in and turn the TruSear™ infrared control knob until the “HIGH” position on the knob aligns with the indicator line on
the control panel. Once lit, turn the control knob to the desired setting. If the burner does not light within 4 seconds,
release and turn the control knob to “OFF.” Wait 5 minutes for any accumulated gas to dissipate and try again. After several
failed attempts, the burner may be lit by turning the control knob to “HIGH” and dropping a match on the face of the
burner. If the burner does not immediately ignite, turn the knob to “OFF”, wait 5 minutes and try again.
Lighting the Grill Burners
Make sure the unit is plugged into a properly grounded receptacle. Turn the appropriate control knob counterclockwise to
any position. This control is both a gas valve and an electric switch. Burners will ignite at any “ON” position with the
automatic re-ignition system. If the flame goes out for any reason, the burners will automatically
re-ignite if the gas is still flowing. When gas is permitted to flow to the
burners, the electric igniters start sparking. On all surface igniters you should hear a clicking sound. If you do not, turn off
the control and check that the unit is plugged in and that the fuse or circuit breaker is not blown or tripped.
Within a few moments, enough gas will have traveled to the burner to be able to light. When the burner lights, turn the
burner control to any position to adjust the flame size. If the burner does not light in four seconds, turn the knob to
“OFF” and wait 5 minutes before trying again. This will allow accumulated gas to dissipate. After several failed attempts
the burner can be lit with a paper book match using the flash
tubes.
8
Lighting Grill Burners
Open the hood or remove covers. Push and turn the control knob until the “HIGH” position on the knob aligns with the
indicator line on the control panel. Press the electronic ignition button corresponding to the burner being lit. You will
hear a clicking sound. Turn the control knob to the desired setting. If the burner does not light in 4 seconds, turn the
knob to “OFF” and wait 5 minutes before trying again. This will allow accumulated gas to dissipate. After several failed
attempts the burner can be lit with a paper book match using the flash tubes. If you have just attempted to light the burner
with the ignitor, allow 5 minutes for any accumulated gas to dissipate.
Lighting Grill
Operation
Flash tubeFlash tubeFlash tube
Lighting Infrared Rotisserie Burner
The location of the infrared burner makes it more susceptible to strong wind conditions—more so than the protected grill
burners. For this reason you should avoid using it during windy conditions.
Open the canopy. Push in and turn the rotisserie control knob until the “HIGH” position on the knob aligns with the
indicator line on the control panel and continue to hold in the knob. Press the electronic ignition button which corresponds
to the rotisserie control knob. You will hear a clicking sound. After the burner lights, hold the rotisserie control knob in about
5 seconds longer or until the burner remains lit. Once lit, turn the control knob to the desired setting. If the burner
does not light within 4 seconds, release and turn the control knob to “OFF”. Wait 5 minutes for any accumulated gas to
dissipate. If the burner does not light after several attempts, then the burner can be lit by holding a lit match to the burner
(with the control knob pushed in at the light position). Push and turn the control knob until the “HIGH” position on the knob
aligns with the indicator line on the control panel. Make sure you are turning the control knob that corresponds with the
burner being lit. If relighting a hot burner, wait 5 minutes. Never leave the rotisserie control knob at “ON” if rotisserie is not
in use.
Loading ...
Loading ...
Loading ...