Loading ...
Loading ...
Loading ...
_JaT:.]o.]_ii[e- iln"_J li_4i_'_]|[O]ll loll _7_,,"_,.Z:.]a[:.]i*i[o]l F111_i I;(-.I,{,1 ale_._ • [;{_J I;t_]_
I-'f:_l[;lq[e]l[*lliT_el[Hll_-11_l_:4'J[e)ll.lpl I;(:_'_']_'F_I J_J'i_l[e] |E I_ B]lq_._]::(F_'_:[_ -"
[q a'F'_ _qin[oi ;f:;o(,] LUfli[ol III1 tli'_ k+l[_,,,l _t'_l] 11;I l]lil[,,-"_=Ftl :{I']I
I
ill.
I
You can check the last portion of a scene you just recorded without changing the setting of
the POWER switch using EDITSEARCH.
Put the camcorder in the Standby mode by ._
pressing the START/STOP button.
Press the - @ side of EDITSEARCH momentarily.
The last few seconds of the recorded portion will be
played back in the viewfinder, After a few seconds of
playback, the camcorder goes back to the standby
mode, ready for the next recording.
4. EDITSEARCH-_
Note on using EDITSEARCH
When you raise the viewfinder and use EDITSEARCH,
hold the viewfinder with your thumb to prevent
movement.
EDWSEARCH
You can check the recorded picture in the viewfinder using EDITSEARCH. Sound cannot
be monitored.
Press the small green button, and slide _!ll_t,e_lll j
the POWER switch to CAMERA.
Set the STANDBY switch up.
I; F.Jr;'Ji111: ilii 131 _'4 :l[d,{,]-L+ I1-1
Keep pressing the + or- side of EDITSEARCH to
view the playback picture:
+ sidefortheplaybackpicture
- sidefor theplaybackpictureinreverse
4,EDITSEARCH- (_
To stop playback
Release EDITSEARCH.
To monitor the sound while viewing the playback picture in the viewflnder
1 Connect an earphone to the • (earphone) jack.
2 Press the small green button and slide the POWER switch to PLAYER.
3 Press ,4<1 to rewind the tape and press _ where you want to stop,
4 Press D to start playback.
You can reshoot a scene over the last recorded portion using EDITSEARCH. The
previously recorded portion will be erased.
Set the STANDBY switch up.
2
Look In the vlewflnder and find the point from
where you want to begin recording by:
Keep pressing the _-side of EDITSE:ARCH
continuously to advance the picture at a normal
playback speed, or the - side to reverse the picture.
At the desired point, release EDITSEARCH.
4
Press START/STOP.
Recording begins from the point you released EDITSEARCH.
A smooth transition between scenes can be made after the
pre-reoorded portion even if STANDBY is turned down and
turned up, or even if the power is turned off and on again,
provided that the tape is not removed.
D
START / STOP
To pause recording
Press START/STOP again.
To stop recording
Set theSTANDBY switchdown,
If the tape reaches near the end during recording
The _ indicator and the red lamp in the viewfinder and the camera recording/battery
lamp on the camcorder blink slowly. When the tape reaches its end, blinking becomes
rapid and beeps sound for about five seconds (if BEEP is set to ON).
Notes on recording
• To record from the beginning of the tape, run the beginning of the tape for about 15 seconds
before recording. This will avoid missing the starting point when the tape is played back.
• When moving from indoors to outdoors, or vice versa, turn STANDBY up and point the
camcorder at a white object for about 10 seconds so that the white balance is properly
adjusted.
Note on standby mode
If you leave the camcorder in the standby mode for 5 minutes or more, the camcorder will
be automatically turned off. To resume the standby mode, turn STANDBY clown and turn it
up again. To start recording, press START/STOP directly.
Note on light sources
Ifyou are shooting a subject in bright conditions just after shooting in a dark place, the picture
may not appear in the viewfinder. In this case, point the camcorder in the other direction.
J
:o
_D
26 Advanced Camera Operation Advanced Camera Operation 27
Loading ...
Loading ...
Loading ...