Loading ...
Loading ...
Loading ...
© 2021 United States Stove Company
5
INSTALLATION
CLEARANCE TO COMBUSTIBLE
36"
36"
CORNER CLEARANCES
Top View Minimum
Corner Clearances from
Combustible Surfaces
BACKWALL
COMBUSTIBLE
CONSTRUCTION
ACCORDING TO
NFPA 211
SIDEWALL
COMBUSTIBLE
CONSTRUCTION
ACCORDING TO
NFPA 211
DASHED LINE SHOWS
HORIZONTAL CHIMNEY
CONNECTOR AND
ADDITIONAL FLOOR
PROTECTION REQUIRED
FLOOR
PROTECTOR
(TOP VIEW) (FRONT VIEW) (SIDE VIEW)
CEILING
BACKWALL
SIDEWALL
CEILING
36”
36”
59”
18”
18”
18”
18”
FLOOR PROTECTOR
Minimum
Floor-to-ceiling
Height
8ft / 2.4m
18”
18”
36”
56”
36”
36"
36"
CORNER CLEARANCES
Top View Minimum
Corner Clearances from
Combustible Surfaces
BACKWALL
COMBUSTIBLE
CONSTRUCTION
ACCORDING TO
NFPA 211
SIDEWALL
COMBUSTIBLE
CONSTRUCTION
ACCORDING TO
NFPA 211
DASHED LINE SHOWS
HORIZONTAL CHIMNEY
CONNECTOR AND
ADDITIONAL FLOOR
PROTECTION REQUIRED
FLOOR
PROTECTOR
(TOP VIEW) (FRONT VIEW) (SIDE VIEW)
CEILING
BACKWALL
SIDEWALL
CEILING
36”
36”
59”
18”
18”
18”
18”
FLOOR PROTECTOR
Minimum
Floor-to-ceiling
Height
8ft / 2.4m
18”
18”
36”
56”
36”
Proper clearances must be maintained for adequate air
circulation. Adequate ventilation must be provided while
operating this stove.
1. The stove must be placed on solid concrete, solid
masonry, or when installed on a combustible oor a
solid surface oor protector listed to UL1618 Type
2 with a minimum of 1˝ thick and a R-value of 3.0 or
greater must be used, such as Hy-C or Imperial Model
UL 5460BK (NOTE: To calculate R-values of equivalent
alternative materials). The base must extend at least
18” beyond the front, rear and sides of the stove, and
must extend underneath and 2˝ beyond each side of
horizontal connector pipe if it is elbowed towards a
wall (see gure 5 and consult local building codes and
re protection ordinances.)
2. The stove must have its own ue. DO NOT CONNECT
THIS UNIT TO A CHIMNEY FLUE SERVING OTHER
APPLIANCES.
3. After observing the clearances to combustible
materials (gure 2 – 4), locate your oor protector
accordingly (gure 2) and carefully place the stove in
your selected location. Install stove pipe, elbows, and
thimble as required, utilizing either a recently cleaned
and inspected 6˝/152mm masonry chimney or a
6˝/152mm I.D. manufactured chimney system listed
to UL 103 HT. Maximum 64 square inches.
4. Use 6˝/152mm diameter minimum 24 MSG Black or 26
MSG Blue round stove pipe. DO NOT USE GALVANIZED
duct pipe. Secure pipe sections with three (3) sheet
metal screws in each stove pipe and/or elbow joint to
rmly hold the pipe sections together. Screws may be
no more than a maximum of 3˝/76mm apart. DO NOT
CONNECT THIS STOVE TO ANY AIR DISTRIBUTION
OR DUCT SYSTEM.
5. Recheck clearances from the stove, connector stove
pipe, and corner clearances using the illustrations and
your local building codes or re protection ordinances.
NOTE: Drywall faced with brick or stone MUST be
considered a combustible surface.
6. DO NOT INSTALL THIS STOVE IN A MOBILE HOME,
MANUFACTURED HOME, TENT OR TRAILER (NO
EXCEPTIONS)
7. The clearances provided are minimum dimensions.
Installation of this stove must comply with your local
building code rulings.
8. This stove is NOT a UL listed stove.
36"
36"
CORNER CLEARANCES
Top View Minimum
Corner Clearances from
Combustible Surfaces
BACKWALL
COMBUSTIBLE
CONSTRUCTION
ACCORDING TO
NFPA 211
SIDEWALL
COMBUSTIBLE
CONSTRUCTION
ACCORDING TO
NFPA 211
DASHED LINE SHOWS
HORIZONTAL CHIMNEY
CONNECTOR AND
ADDITIONAL FLOOR
PROTECTION REQUIRED
FLOOR
PROTECTOR
(TOP VIEW) (FRONT VIEW) (SIDE VIEW)
CEILING
BACKWALL
SIDEWALL
CEILING
36”
36”
59”
18”
18”
18”
18”
FLOOR PROTECTOR
Minimum
Floor-to-ceiling
Height
8ft / 2.4m
18”
18”
36”
56”
36”
MINIMUM CLEARANCES TO
COMBUSTIBLE SURFACES
Unit to Sidewall 36”
Unit to Backwall 36”
Unit Corner to Wall 36”
Pipe Connector to Backwall 38”
Pipe Connector to Ceiling 18”
Loading ...
Loading ...
Loading ...