Loading ...
Loading ...
Loading ...
INSTALLATION STEP 6
Install the Door Control
Locate door control within sight of door, at a minimum height of
5 feet (1.5 m) where small children cannot reach, awayfrom
moving parts of door and door hardware. If installing into drywall,
drill 5/32" holes and use the anchors provided. For pre-wired
installations (as in new home construction), it may be mounted to
a single gang box (Figure 2).
1. Strip 7/16" (11 mm) of insulation from one end of bell wire and
connect to the two screw terminals on back of door control by
color: white wire to 2 and white/red wire to the 1.
2. Removecover by gently prying at slot in top of the cover
with a small flat head screwdriver. Fastenwith 6ABx1-1/4"
self-tapping screws (drywall installation) or 6-32x1" machine
screws (into gang box) as follows:
• Install bottom screw, allowing 1/8" (3 mm) to protrude above
wall surface.
• Position bottom of door control on screw head and slide
down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid cracking plastic
housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standardinstallation only) Run bell wire up wall and
across ceiling to motor unit. Use insulated staples to secure
wire in several places. Do not pierce wire with a staple,
creating a short or open circuit.
4. Strip 7/16" (11 mm) of insulation from end of bell wire.
Connect bell wire to the quick-connect terminals as follows:
white to white and white/red to red.
NOTE: When connecting multiple door controls to the opener,
twist same color wires together. Insert wires into
quick-connect holes: white to white and red/white to red.
5. Position the antenna wire as shown.
6. Usetacks or staples to permanently attach entrapment warning
label to wall near door control, and manual release/safety
reversetest label in a prominent location on inside of garage
door.
NOTE: DONOT connect power and operate openerat this time.
The trolley will travel to the furl open position but will not
return to the dose position until the sensor beam is
connected and properly afigned.
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
• Besure power is not connected BEFOREinstalling door
control.
• Connect ONLYto 24 VOLT low voltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a closing
garagedoor:
• Install door control within sight of garage door, out of reach
of children at a minimum height of 5 feet (1.5 m) and away
from ALL moving parts of door.
• NEVERpermit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLYwhen it can be seen clearly, is properly
adjusted and there are no obstructions to door travel.
• ALWAYSkeep garage door in sight until completely closed.
NEVERpermit anyoneto cross path of closing garage door.
HARDWARESHOWN ACTUALSIZE
Control Panel (std installation) _r _
Insulated
Staples
Control Panel (pre-wired) Drywall Anchors
Figure 1 Figure 2
REMOVE & REPLACE COVER PRE-WIRED
INSTALLATION
TO Replace,
Insert Top
Tabs First / _
24 Volt
2-Conductor
Bell Wire in
Gang Box
Push Bar
2-Conductor
Bell Wire
Quick-Connect
Terminals
(BACK VIEW
Top
- Mounting
Hole
Terminal
Screws
3ottom
tdounting
dole
To release or insert wire,
push in tab with screwdriver
tip
Strip wire 7/16"
(11 mm)
I 7/16" (11 mm)l
Door Control
Connections
White Grey
Antenna
17
Loading ...
Loading ...
Loading ...