Wireless PIR Motion Sensor (IR-S1)
P
P
a
a
r
r
t
t
s
s
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. Learn/Test Button & LED indicator
Press the button to transmit a learn/test code and enter Test
mode for 3 minutes. The LED will light up whenever a movement
is detected under Test mode.
2. Battery Insulator
3. Supervision Enable/Disable Jumper Switch
(JP2)
4
. High/Low Sensitivity Jumper Switch (JP3)
5. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover
opening.
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
1 x PIR Sensor
4 x wall plugs and screws
2 x 1.5V alkaline batteries (pre-installed)
Supervision Enable/Disable Jumper Switch (JP2)
If enabled, the PIR sensor will transmit supervision signal to
Control Panel periodically for the sensor to monitor PIR sensor
condition.
Jumper set to ON = supervision function is Disabled (Default)
Jumper set to OFF = supervision function is Enabled
High/Low Sensitivity Jumper Switch (JP3)
Jumper set to ON = PIR sensitivity is set to High
Jumper set to OFF= PIR sensitivity is set to Low (Default)
Put the Control Panel into learning mode, then press the learn
button to transmit learn code. Please refer to Control Panel
manual for to complete the learning process.
The PIR Sensor has knockouts on the back where plastic is
thinner. The 2 center knockouts are for flat wall mounting, and the
4 side knockouts are for corner mounting.
1. Break through the knockouts; use the knockouts to mark
position on the wall or corner.
2. Drill holes into the wall or corner using the knockouts as
template.
3. Fix the PIR Sensor base onto the wall with the screws and
plugs provided.
4. Replace the PIR Sensor cover onto the base.
S
S
l
l
e
e
e
e
p
p
T
T
i
i
m
m
e
e
r
r
The PIR features a “sleep time” of approximately 1 minute for
power conservation. After transmitting a detected movement, the
PIR will not retransmit for 1 minute. Any further movement
detected during this sleep period will extend the sleep time by
another minute. In this way continuous movement in front of a
PIR will not unduly exhaust the battery.
T
T
e
e
s
s
t
t
M
M
o
o
d
d
e
e
Press the Test Button to enter Test mode for 3 minutes. Sleep
timer will be disabled under Test mode, and the LED indicator will
flash every time a movement is detected. Use the Test mode to
determine PIR detection coverage and plan the installation
location accordingly.
L
L
E
E
D
D
I
I
n
n
d
d
i
i
c
c
a
a
t
t
o
o
r
r
Off Normal Operation
On (2 seconds) - When Tamper Switch is triggered
- Movement detection under low battery,
tamper triggered, or Test mode.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Of
f
if the jumper link is removed
or parked on one pin.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Of
f
if the jumper link is removed
or parked on one pin.
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Surface Fixing
Knockouts x 2
(Inside)
Corner Fixing
Knockouts x 4
Loading ...
