Loading ...
Loading ...
Loading ...
Your new tractor has been assembled at the factory with the exception of those parts left
unassembled for shipping purposes° To ensure safe and proper operation of your tractor
al! parts and hardware you assemble must be tightened securely. Use the correct tools as
necessary to ensure proper tightness°
TOOLS REQUIRED FOR ASSEMBEY"
....A socket wrench set will make assembly
easier. Standard wrench sizes are listed.
(t) 5/I6" wrench Utility knife
(2) 7/i 6" wrenches Tire pressure gauge
(2) 1/2" wrenches Pliers
(1) 9/16" wrench
When right or left hand is mentioned in this
manual, it meanswhenyou are in the operating
position (seated behind the steering wheel),
TO REMOVE TRACTOR FROM
CARTON
UNPACK CARTON
1. Remove all accessible loose parts and
parts boxes from carton,,
2. Cutalong dashed lines on allfour panels
of carton. Remove end panels and lay
side panels flat.
3. Check for any additional loose parts or
cartons and remove.
BEFORE REMOVING TRACTOR
FROM SKID
CHECK BATTERY
1, Lift seat pan to raised position.
NOTE: If this battery is put into service after
month and year indicated on label (label lo-
cated between terminals) charge battery for
minimum of one hour at 6 - 10 amps. (See
"BATTERY" in Maintenance section of this
manual for charging instructions),
Seat
Terminal
Terminal
ATTACH STEERING WHEEL
ASSEMBLE EXTENSION SHAFT AND
BOOT
1. Slide extension shaft onto lower steering
shaft.
2. Place tabs of steering boot overtab slots
in dash and push down to secure.
INSTALL STEERING WHEEL
3. Position front wheels of the tractor so
they are pointing straight forward,
4o Remove steering wheel adapter from
steering wheel and slide adapter onto
..... steering shaft extension,
5. Position steeringwheelso cross bars are
horizontal (left to right) and slide inside
boot and onto adapter_
6. Assemble large flat washer, 5/16 lock
washer, 5/16 hex bolt and tighten se-
curely.
7, Snap steering wheel insert into center of
steering wheel°
8. Remove protective materials from tractor
hood and grill.
IMPORTANT: Check for and remove any
staples in skid that may puncture tires where
tractor is to roll off skid°
L°lnsert
ck
Bolt -_}_ Washer
_c_---_Large Fla! Washer
._.__.Steering
Wheel
Steering
Boot
Adapter---_____,(_
_ Extension
_.___-_Shaft
Lower \_( .....
Steering _'P" ........
Shaft ____., k '""---.-°",,
I ./5_,;1_-'% ',
Tab {_P--'':_"'_ 1'\
Stot--"t_ [ _i./ }
INSTALL SEAT
t. Remove bolt and flat washer securing
seat to cardboard packing and set aside
for assembly of seat to tractor. Remove
the cardboard packing and discar&
2, Connect switch to seat.
3_ Place seat on seat pan so all three (3)
bottom pads are positioned over large
slotted holes in pan.
4, Push down on seat to engage pads in
slots and pull seat towards rear of tractor,
5. Raise seat and tighten bolt securely,
B
CONTROLAI
Si el tractor _
pararse a un_
mAs alto en u
seco o pavirn_
y ajustar eFfr(
CONTROL D
1_ Aparcar e
de hormic
el pedal c
el freno d
2. Desembn
mando de
misi6n de
rueda libr
asi se col
Las ruedas tr
tinar cuando
el tractor man
freno o contac
de servicio CL
PARA REMO
REPARAClO
1.. Bloquee
2. Remueva
ci6n y las
de ias rue
llave cuac
3. Repare la
AVISO: En la.,
las ranuras el
ejeo inserte la
4o Vuelvaac_
de retencid
5. Vuefva a c(
AVISO: Pare
prevenir que t
pequefias fuc
Sears y utilizer
que las Ilanta.,
Anillc
Rete_
Cubierta '
del eje
Llave Cuadrada
trasera solamer
IMPRESION 1
DELANTERA
La impresi6n
teras de sun
y son normal
rJe las ruedas
caso que se F
impresi6n o I_
teras tel corn(
contacto con {
centro de sen
Loading ...
Loading ...
Loading ...