Loading ...
Loading ...
Loading ...
TO START ENGINE
When starting the engine for the first time or
if the engine has run out of fuel, it will take
extra cranking time to move fuel from the
tank to the engine.
1. Be sure freewheel control is in the trans-
mission engaged position_
2. Sit on seat in operating position, depress
brake pedal and set parking brake.
3. Move attachment clutch to disengaged
position_
4. Move throttle control to choke position.
NOTE: Before starting, read the warm and
cold starting procedures below.
5.. Insert key into ignition and turn key
clockwise to start position and release
key as soon as engine starts. Do not run
starter continuously for more than fifteen
seconds per minute. If the engine does
not start after several attempts, move
throttle control to fast position, wait a
few minutes and try again. If engine still
does not start, move the throttle control
back to the choke position and retry
WARM WEATHER STARTING
(50°F (10 ° C) and above)
6. When engine starts, move the throttle
control to the fast position.
• The attachments and ground drive can
now be used. If the engine does not
accept the load, restart the engine and
allow it to warm up for one minute using
the choke as described above_
COLD WEATHER STARTING
(50°F (10 ° C) and below)
6. When engine starts, leave throttle control
in choke position until engine warms up
and begins to run roughly. Once rough
running begins, immediately move the
throttle control to the fast position. Engine
warm-up may take from several seconds
to several minutes (the colder the tem-
perature, the longer the warm-up).
AUTOMATIC TRANSMISSION WARM UP
Before driving the unit in cold weather, the
transmission should be warmed up as follows:
1. Be sure the tractor is on level ground,
2. Release the parking brake and let the
brake slowly return to operating position.
3. Allow one minute for transmission to
warm uF This can be done during the
engine warm up period.
. The attachments can also be used dur-
ing the engine warm-up period after the
transmission has been warmed up,,
NOTE: If at a high altitude (above 3000
feet) or in cold temperatures (below 32 F)
the carburetor fuel mixture may need to be
adjusted for best engine performance (see
"TO ADJUST CARBURETOR" in the Service
and Adjustments section of this manual),
PURGE TRANSMISSION
_CAUTION: Never engage or disengage
freewheel lever while the engine is running.
To ensure proper operation and performance,
it is recommended that the transmission be
purged before operating tractor for the first
time. This procedure will remove any trapped
air inside the transmission which may have
developed during shipping of your tractor,
IMPORTANT: Should your transmission
require removal for service or replacement.
it should be purged after reinstallation before
operating the tractor.
I. Place tractor safely on a level surface -
that is clear of objects and open - with
engine off and parking brake set°
2. Disengage transmission by placing
freewheel control in disengaged position
(See "TO TRANSPORT' in this section
of manual).
3. Sitting in the tractor seat, start engine.
After the engine is running, move throttle
control to stow position. Disengage park-
ing brake.
&CAUTION: At any time, during step 4,
there may be movement of the drive wheels.
4. Depress forward drive pedal to full for-
ward position and hold forfive (5) seconds
and release pedal. Depress reverse drive
pedal to full reverse position and hold
for five (5) seconds and release pedal.
Repeat this procedure three (3) times,
5. Shutoff engine and set parking brake.
6. Engagetransmissionby pfacingfreewheel
control in engaged position (See "TO
TRANSPORT" in this section of manual),
7. Sitting in the tractor seat, start engine,
After the engine is running, move throttle
control to half (1/2) speed. Disengage
parking brake.
8. Drive tractor forward for approximately
five feet then backwards for five feet. Re-
peat this driving procedure three times.
Your transmission is now purged and now
ready for normal operation_
18
PARA HACI
AI hacer arran
se ha acabadc
itar& tiempo p_
combustible c
1, AsegOres_
en la post,
2o Si6ntase
aci6n, su{
freno de e
3, Mueva e
posici6n o
4, Mueva la
a ia posici
AVlSO: Antes
guientes para_
5_ Insertelai
el sentido
posici6n d
pronto cot
cionar el
dequince
arranca dE
el control
r&pido, es
de nuevo
mueva el
posici6n d,
ARRANQUE !
(50°F(I0°C)
6, Cuando a
de ]a acel,
• Los accesc
set utilizadc
vuelva a arl
se caliente
gulador cor
ARRANQUE I
(50°F(10°C) "_
6, AI hacer
control de
trangulaci
empieze ft
a funcion_
control de
El calenta
partir de \
(cuanto m
es el calel
Loading ...
Loading ...
Loading ...