Loading ...
Loading ...
Loading ...
TRACTOR
Always observe safety rules when performing
any maintenance,.
BRAKE OPERATION
if tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be serviced., (See "TO CHECK
.......... BRAKE" in the Service and Adjustments
section of this manual).
TIRES
. Maintain proper air pressure in all tires
(See the sides of tires for proper PSI).
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may cause
tire damage.
NOTE: To seal tire punctures and prevent
fiat tires due to slow leaks, tire sealant may
be purchased from your local parts dealer.
Tire sealant also prevents tire dry rot and
corrosion.
OPERATOR PRESENCE SYSTEM AND
REVERSE OPERATION SYSTEM (ROS)
Be sure operator presence and reverse
operation systems are working properly. If
your tractor does not function as described,
repair the problem immediately_
. The engine should not start unless the
brake pedal is fully depressed, and the
attachment clutch control is in the disen-
gaged position.
CHECK OPERATOR PRESENCE
SYSTEM
. When the engine is running, any attempt
by the operator to leave the seat without
first setting the parking brake should shut
off the engine.
• When the engine is running and the at-
tachment clutch is engaged, any attempt
by the operator to leave the seat should
shut off the engine.
• The attachment clutch should never oper-
ate unless the operator is in the seat.
@
ROS "ON" Position
Engine "ON" Position
(Normal Operating)
CHECK REVERSE OPERATION (ROS)
SYSTEM
" Whentheengineis runningwiththe ignition
switch in the engine "ON" position and the
attachment clutch engaged, any attempt
by the operator to drive in reverse should
shut off the engine,
• When the engine is running with the ignition
switch in the ROS "ON" position and the
attachment clutch engaged, any attempt
by the operator to drive in reverse should
. NOT shut off the engine°
BLADE CARE
For best results mower blades must be sharp,.
eplace worn, bent or damaged blades.
CAUTION: Use only a replacement
blade approved by the manufacturer of your
tractor. Using a blade not approved by the
manufacturer of your tractor is hazardous,
could damage your tractor and void your
warranty.
BLADE REMOVAL
1o Raise mowerto highest position to allow
access to blades.
NOTE: Protect your hands with gloves and/
or wrap blade with heavy cloth.
2. Remove blade bolt by turning counter-
clockwise_
3, Install new blade with stamped "GRASS
SIDE" facing the ground°
IMPORTANT: To ensure proper assembly,
center hole in blade must align with star on
mandrel assembly_
4. Install and tighten blade bolt securely
(45 - 55 Ft. Lbso torque).
IMPORTANT: Special blade bolt iS heat
treated.
Slar
Center Hole
Blade Bolt Mandrel
(Special) "_-_),_"" Assembly
Blade
PARA AJUS'f
LA SEGADOI
La posiciSn de
a qu6 altura s,
::;;:_!i!_i!!!:i
• Coloque la
la altura de,.
La gama de I;
damente 1 a
desde el sue!{
el motor no e_
aproximadas
condiciones d
del tipo del c6
• El c6sped p_
mente a 2 -
fria y sobn
calurosos_ f
able y de rr
y despu6s
, Para obten_
c6sped que
debe segars
ativamente
PARA OPERt
Su tractor vie
sensor que el
el motor estb. t
cesorio est& e
bajarse del as
que mantene
mente en et
vacile o se ap
en terreno dis
t. Seleccion,
2_ Baje la s_
tamiento c
3. Haga arra
engancha
accesorio_
20
Loading ...
Loading ...
Loading ...