Loading ...
Loading ...
Loading ...
b. MoDELS REQUtRING
POWER
SUppLY
CORD KtT
RISK OF FIRE OR ELECTRICAL SHOCK MAY
OCCUR IF AN
INCORRECT SIZE
RANGE CORD
KIT IS USED, THE INSTALLATION
INSTRUCTIONS ARE NOT FOLLOWED OR STRAIN
RELIEF
BRACKET IS
DISCARDED.
This appliance may be connected
by
means of
a
power
supply cord. Only a
power
supply cord kit raled 120/240 volts,40
amperes and marked for use with ranges shall be used.
.
Use only a 3-conductor or a 4-conductor UL-listed range
cord. These cords must be
provided
with closed-loop terminals
on
wire and a strain relief device
properly
installed.
.
A time-delay fuse or circuit breaker is recommended.
r
Local
codes may
permit
the use of a Ul-listed, 250 volt,
40
amp range
power
supply
cord
(pigtail)
This cord contains three
No. 10 copper wires
and matches a 3-wire
receptacle of NEMA Type 10-50R. Connectors on the appliance end must be
provided
at the
point
the
power
supply
cord
enters the appliance.
.
The range can be connected
directly
to the fused disconnected
(or
circuit breaker box) through flexible armored conduit.
Allow 2 to 3 feet of slack in the line so that it can be moved if servicing is ever necessary.
o An UL-listed conduit connector must be
provided
at each end of the
power
supply cable
(at
the range and at the
junction
box)
o
Wire
sizes and connections must conform to the rating of the range
(40
amp)
The wiring diagram
is located on the back of the
range
in a bag.
For
power
cord
¡nstallations
only:
WARN ING: Electrical Shock Hazard
r
Disconnect
power
before
servicing.
|
.
Plug into a
grounded
outlet.
.
Use
a new 40Amp
power
supply cord.
|
.
Failure to
follow
these
instructions can
result
in death, fire or electrical shock.
Assemble the strain relief in the hole. lnsert the
power
cord through the strain relief and tighten. Allow enough slack to easily
attach the cord terminals to the terminal block. lf tabs are
present
at the end of the winged strain relief, they can be removed
for
better
fit.
lmportant: Do not
install
the
power
cord without a strain relief.
The
strain relief bracket should be installed before
reinstalling the rear range wiring cover.
3-CONDUCTOR POWER CORD INSTALLATION
Use this method only if local codes
permit
connecting cabinet-ground conductor to neutral wire of
power
supply cord.
.
Remove the wire cover
(on
the back
of
range) by removing 3 screws using a Phillips screwdriver. The terminal block will
then be accessible.
.
Remove the knockout ring
(1
3/8") located on bracket directly below the terminal block. To remove
the
knockout, use a
pair
of
pliers
to bend
the knockout
ring away
from the bracket and twist until ring is removed.
.
Assemble a U.L.-listed strain relief in the
opening.
'
.
lnsert the
power
supply
cord
through
the strain reliel allowing enough slack
to
easily attach
the wiring to the terminal
block.
.
Use only ring
terminals to connect the
power
supply.
'
.
Use a1/q"
nut driver and remove the
hex
washer head
nuts
from
the terminal block.
¡
Connect
the outer wires to the outside terminals and the center wire to the center terminal. Securely tighten nuts for
proper
electrical connection.
Do
not
remove the
ground
strap.
.
Tighten
the strain relief
screws.
.
Re-install the wire cover with
the
3 screws
removed
earlier. Make sure the wires do not become
pinched
between the wire
cover
and main back.
Loading ...
Loading ...
Loading ...