Loading ...
Loading ...
Loading ...
Bepre you bedn:
You must set Home in Location, '"-, p.31
Otherwise, personalized Picture and Sound settings will not be
memorized after the unit goes into Standby mode,
1 Press 1_ and use • • to select Sound, then press OK.
m
2 Use •T_II_
m
to select the item you want to adjust, then press OK.
to select the desired setting, then press OK.
(Personal, Standard, Vivid, Sports, Movie, Music and News)
Auto sound When you adjust the following sett}ngs (Equalizer, SRS
TruSurround XT ×, Incredible Surround x and Auto volume
leveling), Personal sound will be set automaticall}4
Adjust the tonal quality for each frequency.
I c@
Equalizer to adjust each level of tonal quality
PressBACK to go backto the previous menu.
This selects sound modes for more spatial or surround sound reproduction,
*SRS Off __
TruSurround XT On R)
I __ und X] '_)to On
Incredible Surround gives you the stereophonic virtual space through
your existing 2-channel stereo system.
*Incredible I Off t Natural effectSurround On Emphasizedeffect.
÷ This part differs depending on the product you have.
• SRSTruSurround XT for 40PFL4708, 39PFL2708,32PFL3508,32PFL4508,
29PFL4508,24PFL4508.
• Incredible Surround for SOPFL3708,46PFL3708, 40PFL1708.
This function keeps a constant loudness differential between the TV
commercials and the programs.
Off to remove the auto volume leveling
Auto volume
leveling On to reduce volume differences between
the T1! commerciaB and the programs
You can select the Audio Output from the unit's speakers or not. If your
amplifier is HDPII link function compatible and connected by an HDPII
cable to this unit, some sound operations such as volume up can be
changed by using this unit's remote control.
On to output sound fi_om the unit's speakers
Off not to output sound fi_om the unit's
speakers
TV speakers to control Audio Output fi_om your
Speakers connected EasyLink Compliant Devices
EasyLink with VOL + / - by using this unit's
remote control.
You can select audio output through a digital audio output connector.
to output multichannel signals.
(When the audio of the content is PCM,
Digital output Multichannel it will be output in PCPq even if
format Hultichannel is selected.)
PCM to output PCN signals.
@ i i iii¸
You can set the output mode as a default for the sound mode (Analog
TV only),
This setting is not interlocked when you change the output mode by
pressing SAP, Refer to Switching audio mode, '"-_p.19
Stereo to output stereo-audio
Audio setting Mono to output mono-audio
SAP to output second audio program
Before you begin:
Make sure the unit is connected to antenna or cable,
1 Press _ and use • • to select Setup, then press OK.
2 Adjustthe following items,
Autoprogram
Be sure the RF cable is correctly connected to this unit and you are
registered with your cable TV provider when you install Cable channels.
2
Use • • to select Autoprogram, then press OK,
• If you run Autoprogram when you have locked channels, a
message appears asking to enter your PIN. Enter your PIN in
order to complete the installation. You need to set the channel
loci< again after the installation,
Use • • to select an appropriate option, then press OK,
- When Antenna is selected, the TV detects any off-the-air
antenna signals, It searches for ATSC (Digital) and NTSC
(Analog) channels available in your area,
- When Cable is selected, the TV detects signals supplied by cable,
It searches for DTV, Analog TV and Cable channels available in
your area.
Continued on next page.
Loading ...
Loading ...
Loading ...