Aeroplus AAPC10RC1 10,000 BTU 115-Volt Portable Air Conditioner

USER MANUAL Portable Air-conditioner

Specification

Name of Parts

Accessories

After unpacking, please check whether the above-mentioned accessories are included, and check their purposes in the installation introduction in this manual.

Appearance and Function of Control Panel

Cooling only model

Appearance and Function of Remote Control

Power on/off Timer on/off Operation MODE Fan speed Temperature up Temperature down

Notes:

- Do not drop the remote control.

- Do not place the remote control in a location exposed to direct sunlight.

Operation Introduction

Before starting operations in this section:

1) Find a place where there is power supply nearby.

2) As shown in Fig.2 and Fig.2a, install the exhaust hose, and adjust the window position well.

3) Insert the power cord into an grounded AC115V/60Hz socket;

4) Press the POWER button to turn on the air-conditioner.

Before using

Notice:

-Operation temperature range:

Check up whether the exhaust hose has been mounted properly. Cautions for cooling and dehumidifying operations:

• When using functions on cooling and dehumidifying, keep an interval of at least 3 minutes between each POWER.
• Power supply meets the requirements.
• The socket is for AC use. -Do not share one socket with other appliances.
• Power supply is AC115V/60Hz

1.Power off memory (Auto-restart operation)

• If the unit loses power unexpectedly, it will restart with the previous function settings when power is restored

2. Cooling operation

• Press the “Mode” button till the “Cool” icon appears.
• Press the “▲”or“ ▼”button to select a desired room temperature. (60°F-90°F)
• Press the “Fan Speed” button to select wind speed.

3.Dehumidifying operation

Press the “Mode” button till the “Dehumidify” icon appears .

• Automatically set the selected temperature to current room temperature minus 2°F.
• Automatically set the fan motor to LOW wind speed.

4. Fan operation

• Press the “Mode” button till the “Fan” icon appears.
• Press the “Fan Speed” button to select wind speed.

5. Timer operation

Timer ON setting:

• When the air-conditioner is OFF, press the “Timer” button and select a desired ON time through the temperature and time setting buttons.
• “Preset ON Time” is displayed on the operation panel.
• ON time can be regulated at any time in 0-24 hours.
• Press the “Fan Speed” button to select wind speed.

Timer OFF setting

• When the air-conditioner ON, press “Timer” button and select a desired OFF time through the temperature and time setting buttons.
• “Preset OFF Time” is displayed on the operation panel.
• OFF time can be regulated at any time in 0-24 hours.

6. Water drainage

Water Full Alarm

The inner water tray inside the air-conditioner has one water level safety switches, it controls water level. When water level reaches an anticipated height, the water full indicator lamp lights up. (If water splash motor is damaged, when the water is full, please remove the rubber blockage at the bottom of unit, and all water will drain outside.)

Continuous Drainage

• When you plan to leave this unit unused for a long time, please remove the rubber blockage from the drainage hole at the bottom of unit, and connect a drain hose to the lower fixing clip. All the water in the water tray will drain outside.
• You can drain the water as the above when the unit working at the HEAT mode.
• If water splash motor is damaged, continuous drainage can be used, and under this condition, the water splash motor is not activated. The unit can also work well.
• If water splash motor is damaged, intermittent drainage can also be used. Under this condition, when the water full indicator lamp lights up, please connect a drain hose to the lower fixing clip, then all the water in the water tray will be drained outside. The unit can also work well.

Installation Explanations

Installation Explanations:

• A removal air-conditioner shall be installed in the flat and empty place all around. Don’t block the air outlet, and the required distance around should be at least 30cm. (See Fig.3)
• Should not be installed in wet location, such as the laundry room.
• Socket wiring should be in accordance with the local electric safety requirements .

Introduction to Exhaust Hose Installation

A) Temporary installation

1. Twist both ends of the exhaust hose into the Hose Connector.

2. Insert the fixing clip of the housing adaptor into the openings at back of the air conditioner

3. Put the other end of the exhaust hose to the near windowsill.

B) Window Slider Kit Installation

The installation manner of window slider kit is mostly in “horizontal” or “vertical”. As shown Fig.5 and Fig.5a, check the min. and max. size of the window before the installation.

1. Install the window kit on the window;
2. Adjust the length of the window slider kit according to the window width or height, and fix it with the dowel;
3. Insert the window connector hose to the hole of the window kit(Fig.5b).

Maintenance Explanations

Water Full Alarm Function

The inner water tray in the air-conditioner has one water level safety switches, it controls water level. When water level reaches an anticipated height, the water full indicator lamp lights up. (If water splash motor is damaged, when the water is full, please remove the rubber blockage at the bottom of unit, and all water will drain outside.)

Maintenance Explanations

Declaration:

1) Before cleaning, be sure to disconnect the unit from any electric supply outlet;

2) Do not use gasoline or other chemicals to clean the unit;

3) Do not wash the unit directly;

4) If the conditioner is damaged, please contact the dealer or repair shop.

1. Air Filter

- If the air filter becomes clogged with dust/dirt, the air filter should be cleaned once every two weeks.

- Dismounting

Open the air inlet grille and take off air filter.

- Cleaning

Clean the air filter with neural detergent in lukewarm（104℉）and dry it up in the shade. Maintenance Explanations

- Mounting

Putting the air filter into the inlet grille, replace the components as they were.

Clean the Air-conditioner Surface

First clean the surface with a neutral detergent and wet cloth, and then wipe it with a dry cloth.

Troubleshooting

Note: The real products may look different.

Related Products