Loading ...
Loading ...
Loading ...
Page 5 of 8
ASSEMBLY INSTRUCTIONS (continued)
ASSEMBLY INSTRUCTIONS (continued)
200810
2. AUTO MODE (nighttime operation only)
● To shift to “AUTO” mode, slide the Time Delay switch to the desired time setting (1min, 2min,3 min). At dusk, the
light turns on to pre-selected low level brightness. When motion is detected, the light turns to full brightness and
stays on as long as motion continues. When the motion is no longer detected, the light at full brightness remains
on for the predetermined time you set (1min, 2min,3 min), and then switches back to low level automatically.
● The light turns off automatically at dawn.
Note: You can adjust the low-level (0~50%) and high-level (50~100%)
brightness by using the low-level (0~50%) and high-level
(50~100%) brightness knob. (See Fig. 6)
3 HOURS (3H) MODE (nighttime operation only)
● The light turns to high-level brightness (100%) at dusk, and stays "ON"
for 3 hours. Then it turns to low-level brightness. It turns to high-level
brightness (100%) when motion is detected, and stays on as long as
motion continues. When motion is no longer detected, it remains on for
the predetermined shut-off delay time you set (1min, 2min,3 min), and
then returns to the predetermined low-level brightness automatically.
● The light turns off automatically at dawn.
Note: You can adjust the low-level (0~50%) and high-level (50~100%)
brightness by using the low-level (0~50%) and high-level
(50~100%) brightness knob. (See Fig. 6)
4. 6 HOURS (6H) MODE (nighttime operation only)
● The light turns to high-level brightness (100%) at dusk, and stays "ON"
for 6 hours. Then it turns to low-level brightness. It turns to high-level
brightness (100%) when motion is detected, and stays on as long as
motion continues. When motion is no longer detected, it remains on for
the predetermined shut-off delay time you set (1min, 2min,3 min), and
then returns to the predetermined low-level brightness automatically.
● The light turns off automatically at dawn.
Note: You can adjust the low-level (0~50%) and high-level
(50~100%) brightness by using the low-level (0~50%)
and high-level (50~100%) brightness knob. (See Fig. 6)
5. PHOTOCELL (PC) MODE (nighttime operation only)
● The light turns on at full brightness at dusk and remains
on until dawn.
Note: You can adjust the high level brightness (50%~100%)
by using the high level brightness knob. (See Fig. 6)
6. Manual Override (nighttime operation only)
● To temporarily override the settings in “AUTO”, “3H” or “6H”
modes for on-demand continuous full-brightness at night,
turn the wall switch “OFF” then turn it “ON” twice within 3
seconds. The light remains on all night long. To shift back
to “AUTO”, “3H” or “6H” mode, turn the wall switch “OFF”
then turn it “ON” twice within 3 seconds again.
● The light turns off automatically at dawn.
7. Emergency Backup (nighttime operation only)
● Emergency backup works when AC power failure, the light lasts on 30
seconds and then enters the AUTO mode, When motion is detected ,the
light turns on at 400lm brightness,the light remains on for predetermined
shut-off delay time you set (1min ,2min,3min),and then turns off.
When AC power supply recovery, the light warm up 30 seconds and
then restore the previous function you set.
Note: To make sure the above functions operate properly, always keep the wall switch in
the “ON” position (including the daytime).
LOW LEVEL
HIGH LEVEL
25%
0
50%
75%
50%
100%
FUNCTION AND OPERATION (continued)
Fig. 5
Fig. 6
“AUTO” “3H”
or “6H” Mode
Manual
Override
Manual Override Operation Diagram
Turn wall switch OFF-ON
-OFF-ON in 0.5~3 Seconds
Turn wall switch OFF-ON
-OFF-ON in 0.5~3 Seconds
Fig. 7
MODE
SENSITIVITY
TIME
L
M
H
6H
AUTO
3H
PC
TEST
1MIN
2MIN
3MIN
Loading ...
Loading ...
Loading ...