Loading ...
T8. AUTOMATIC “COOKSENSE” FUNCTION
The hood will automatically set an extraction speed of 1, and then
increase it if necessary (according to the ambient conditions detected
by the hood sensor).
If the hood is using extraction speed 1 and there is no change in the
ambient conditions, it will switch o after 5 minutes.
NB: to make sure this function is used correctly, please congure the
parameters for automatic mode rst as described in the relevant section.
NB: if you change any other speed control functions while automatic
mode is active, the auto ventilation function will switch o.
T9. FILTER SATURATION INDICATOR
At regular intervals, the hood signals the need to perform lter
maintenance.
Please note: The indicators will only work when the hood is on.
T9 button lit: carry out maintenance on the grease lter.
T9 button ashing: carry out maintenance on the carbon lter.
Resetting the lter saturation indicators:
Please note: This must be done with the hood switched on.
Press and hold the T9 button. The light will switch o to conrm the
reset.
Activating the carbon lter saturation indicator.
Please note: This must be done with the extraction motor switched o.
This indicator is normally deactivated. It should be activated if the
hood is installed in the ltering version (i.e. with carbon lters).
Press and hold buttons T1 and T10 simultaneously to activate the
function. The buttons will light up to indicate activation.
To deactivate the function, press and hold the same buttons (T1 and
T10) again. The buttons will ash briey and then switch o to indicate
deactivation.
T10. ON/OFF “BREATH DAILY CYCLE”
The hood will automatically set an extraction speed of 1, and then
increase it if necessary (according to the ambient conditions detected
by the hood sensor).
If the extraction speed does not change owing to the ambient
conditions detected, the hood will switch o after two hours.
The hood will switch o in any case after ve hours in use, regardless of
the operating mode.
Please note: to make sure this function is used correctly, please congure
the parameters for automatic mode rst as described in the relevant
section.
T11. ON/OFF “BREATH INTENSIVE CYCLE“
The hood will automatically set an extraction speed of 5, and then
increase it if necessary (according to the ambient conditions detected
by the hood sensor).
If the extraction speed does not change owing to the ambient
conditions detected, the hood will switch o after two hours.
The hood will switch o in any case after ve hours in use, regardless of
the operating mode.
Please note: to make sure this function is used correctly, please congure
the parameters for automatic mode rst as described in the relevant
section.
T12. LIGHT INDICATOR FOR WIFI FUNCTION ACTIVE
The indicator comes on when the hood is controlled from a distance
via the app.
T13. WIFI CONNECTION
Press to activate/deactivate the WI-FI functions.
This function allows the hood to be connected to the Internet so you
can monitor/control it from a distance via a smartphone or tablet.
To use the WI-FI function, connect the appliance to the domestic
wireless network (Internet) following the conguration procedure
explained in the “WI-FI MANUAL”.
CONFIGURING THE PARAMETERS FOR AUTOMATIC MODE
To make sure that automatic mode is used correctly, you will need to
calibrate the hood and select the hob type.
Calibrating the hood
NB: this must be done with the appliance on standby - i.e. one minute after
switching o the motor.
Press and hold the T4 button for ve seconds.
Extraction speed 1 will be activated and the T4 button will ash to
indicate that hood calibration has started (this will take approx. 5
minutes).
Please note: To stop the calibration process, press and hold the T4 button
for ve seconds. Calibration will then be invalidated and will therefore
need to be repeated.
Please note: Calibration will be carried out automatically when the power
supply to the product is switched on for the rst time. T4 will ash. Wait 5
minutes for the calibration to be completed.
Selecting the hob type
NB: this must be done with the appliance on standby - i.e. one minute after
switching o the motor.
Press and hold the T10 and T11 buttons for ve seconds.
The T10 and T11 buttons will light up.
If using gas to power the hob, press the T10 button – the button will
ash to indicate that this has been selected.
If using electricity to power the hob, press the T11 button – the button
will ash to indicate that this has been selected.
Once pressed, the button will ash for three seconds to indicate that
your selection has been saved.
TECHNICAL DATA
Height (cm) Width (cm) Depht (cm) Ø of exaust tube (cm)
110 - 129.5 89.8 32 15
CLEANING AND MAINTENANCE
CLEANING
• Do not use steam-cleaning equipment.
• Disconnect the appliance from the mains.
Important: do not use corrosive or abrasive detergents. If any such
products unintentionally come into contact with the appliance, clean
the appliance immediately with a damp cloth. Do not use alcohol.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few
drops of washing-up detergent to the water. Finish o with a dry
cloth.
Important: do not use abrasive sponges or metallic scrapers or
scourers. Over time, these can ruin the enamel surfaces.
• Use detergents specically designed for cleaning the appliance
and follow the manufacturer's instructions.
Important: clean the lters at least once a month to remove oil and
grease residue.
MAINTENANCE OF THE GREASE FILTERS
This must be cleaned once a month (or when the lter saturation
indication system - if envisaged on the model in possession - indicates
this necessity) using non aggressive detergents, either by hand or in the
dishwasher, which must be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease lter may discolour slightly,
but this does not aect its ltering capacity.
Pull out the handle to remove the lter.
Once the lter has been washed and left to dry, proceed in reverse
order to ret the lter.
Loading ...
Loading ...
Loading ...