User Manual Whirlpool WHSS 90F Cooker Hood - Black

Documents for Whirlpool WHSS

The following documents are available:
User Manual Photos
WHSS photo
EN
Quick guide
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT
In order to receive a more complete assistance, please
register your product on www . whirlpool . eu/ register
Before using the appliance carefully read the Safety
Instruction.
PRODUCT DESCRIPTION
FIRST TIME USE
AIR VENT (FOR THE SUCTION VERSIONS)
Connect the hood and discharge holes on the walls with a diameter
equivalent to the air outlet (connection ange).
Using the tubes and discharge holes on walls with smaller dimensions
will cause a diminution of the suction performance and a drastic
increase in noise.
Any responsibility in the matter is therefore declined.
! Use a duct of the minimum indispensible length.
! Use a duct with as few elbows as possible (maximum elbow angle: 90°).
! Avoid drastic changes in the duct cross-section.
! The company declines any responsibility whenever these regulations
are not respected.
FILTERING OR DUCTING?
! Your cooker hood is ready to be used in suction version.
To use the hood in ltering version the special ACCESSORY KIT must be
installed.
Check if the ACCESSORY KIT is furnished or must be bought separately.
Note: If furnished, in certain cases, the additional activated carbon ltering
system may be installed on the hood. Information about the conversion of
the hood from suction version to ltering version is present in the Manual
“Safety Instructions & Installation.
DUCTING VERSION
In this case the fumes are conveyed outside of the building by means
of a special pipe connected with the connection ring located on top of
the hood.
Attention! The exhausting pipe is not supplied and must be purchased
apart. Diameter of the exhausting pipe must be equal to that of the
connection ring.
Attention! If the hood is supplied with active charcoal lter, then it
must be removed.
FILTER VERSION
The aspirated air will be degreased and deodorised before being fed
back into the room.
In order to use the hood in this version, you have to install a system of
additional ltering based on activated charcoal.
CONTROL PANEL
T1. ON/OFF “Night Light”
T2. Hob lights ON/OFF – Select the colour
temperature
T3. Autolight” function
T4. “ZEN Mode” function
T5. Motor ON/OFF
T6. POWER BOOST 1” function
T7. “POWER BOOST 2” function
T8. Automatic “COOKSENSE” function
T9. Filter saturation indicator
T10. ON/OFF “Breath Daily Cycle
T11. ON/OFF “Breath Intensive Cycle"
T12. Light indicator for WI-FI function active
T13. WI-FI connection
T1. ON/OFF “NIGHT LIGHT”
Press to switch the soft background lighting on or o.
T2.
HOB LIGHTS ON/OFF  SELECT THE COLOUR TEMPERATURE
Press to switch the hob lights on or o.
With the lights on, swipe the SL1 LED strip with your nger
to increase or decrease the light intensity (to the right or left
respectively).
Press and hold to set the light colour temperature.
Swipe the SL1 LED strip with your nger to set a colder or warmer
colour (to the right or left respectively).
If you do not change the colour for ve seconds, SL1 will ash at
the colour setting you have selected and an audible signal will
sound to indicate that the system has saved this conguration.
NB: the light will come on at the last colour temperature set before
switching o the appliance.
T3. “AUTOLIGHT” FUNCTION
Press to activate/deactivate the “Autolight” automatic lighting
function.
NB: this function is only activated when the hood is connected via
wi- to the hob. Once the function has been activated, the hob light is
automatically managed on the basis of the hob status.
T4. “ZEN MODE” FUNCTION
Press to activate or deactivate the "ZEN" extraction mode.
This function makes it possible to activate an extraction speed with the
perfect balance between quietness and extraction eciency.
T5. MOTOR ON/OFF
Press to switch the extraction motor on or o.
With the motor on, swipe the SL2 LED strip with your nger to
increase or decrease the extraction speed (power) (to the right or
left respectively).
T6. “POWER BOOST 1 FUNCTION
With the extraction motor on, press T6 to activate the "POWER BOOST
1" intensive extraction speed (time-controlled).
NB: the hood will go back to its previous speed after ve minutes.
T7. “POWER BOOST 2” FUNCTION
With the extraction motor on, press T7 to activate the "POWER BOOST
2" intensive extraction speed (time-controlled).
Please note: the hood will go back to running at the speed it was
previously using after ve minutes.
Loading ...
Loading ...
Loading ...