PSB42YSNSS User Manual

Loading ...

20 49-1000364 Rev. 1

INSTALLATION INSTRUCTIONS

Installation Instructions

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

The refrigerator is much heavier at the top than at the

bottom—be careful when moving. When using a hand

truck, handle from the side only.

• Carefully cut banding at the top and bottom, remove

the outer carton.

• Slide out the back corner posts (2).

• Slide the carton off the top of the cabinet.

NOTE: ,7,61271(&(66$5<72/$<7+(

&$%,1(7'2:1,125'(5725(029(7+(

6.,'

• The unit is secured to the skid with 4 slotted tie-

GRZQVWUDSV5HPRYHWKHVL[´EROWVIURPWKH

base channels in the tie-downs.

5HPRYHWKHVL[´EROWVVHFXULQJWKHVWUDSVWR

the skid.

NOTE: '2127$77(0377252//81,72))

6.,'

• The support blocks on the bottom of the refrigeration

case must be removed

before the refrigerator is

taken off the skid or damage

will occur. Carefully tilt the

refrigerator and slide the

blocks out from beneath.

• Remove the toekick and set

aside for final installation.

• Lift the refrigerator off the

skid with an appliance dolly.

Handle from the sides.

Remov

Tie Dow

Toekick

STEP 2 MOVE THE

REFRIGERATOR INTO THE HOUSE

• Re-use the corner posts from the packaging to

protect stainless steel models. Run the appliance

dolly straps over the posts and under the handles.

• Leave the protective film on the refrigerator until

installation is complete. IMPORTANT: Never lift the

refrigerator by the handle or push against the grille

SDQHOWKLVFRXOGFDXVHGDPDJHRUPLVDOLJQPHQW

• Avoid laying the unit on its back or side to prevent

sealed system restrictions.

STEP 3 INSTALL WATER LINE

• A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 p.s.i. (275-827 kPa).

5RXWH´2'FRSSHURU6PDUW&RQQHFW



plastic

tubing between house cold water line and the water

connection location.

• The tubing should be long enough to extend to the

front of the refrigerator. Allow enough tubing to

accommodate the bend leading into the water line

connection.

NOTE: The only GE Appliances approved

plastic tubing is supplied in the SmartConnect



5HIULJHUDWRU7XELQJNLWV'RQRWXVHDQ\RWKHU

plastic water supply line because the line is under

pressure at all times. Other types of plastic may

crack or rupture with age and cause water damage

to your home.

WARNING

Connect to potable water supply

only. A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 psi (275-827 kilopascals).

WARNING

ELECTRIC SHOCK HAZARD

$WWDFKWXELQJFODPSXVLQJH[LVWLQJKROHRQO\'2

NOT drill into the refrigerator.

Floor

Cold Water Line

AVERTISSEMENT

Raccordez l’appareil à

une alimentation d’eau potable seulement. Une

alimentation d’eau froide est requise pour faire

fonctionner la machine à glaçons et le pichet à

remplissage automatique. La pression d’eau doit se

situer entre 40 et 120 psi. (275 à 827 kPa).

AVERTISSEMENT

RISQUE DE DÉCHARGE

ÉLECTRIQUE

)L[H]OHFROOLHUGHVHUUDJHGDQVOHWURXSUpVHQW

VHXOHPHQW1(3(5&(=3$6GDQVOHUpIULJpUDWHXU

ADVERTENCIA

Realice la conexión a un

suministro de agua potable únicamente. Se requiere

un suministro de agua fría para el funcionamiento

de la máquina de hielos automática y de la jarra de

llenado automático. La presión del agua deberá estar

entre 40 y 120 p.s.i. (275 – 827 kPa).

ADVERTENCIA

PELIGRO DE

DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

Loading ...

User Manual - Page 20