EC860M Instructions for use

Loading ...

Instructions for use

programming menu, press button again.

Setting the temperature

To modify the temperature (low, medium, high) of the water

used to make the coee, proceed as follows:

1. Accesstheprogrammingmenu;

2. Keep button pressed until the lights relative to the

wanted temperature turn-on (see chart below).

3. When the lights relative to the wanted temperature turn-

on, release the button.

4. Press to turn the appliance o (stand-by).

Adjust Stand-by

The machine is pre-set to switch to stand-by after 75 minutes

of non-use. This time interval can be modied so that the

appliance switches o after 15 minutes or after 3 hours.

Proceed as follows:

1. Accesstheprogrammingmenu;

2. Keep the button pressed until the lights relative to

the desired stand-by interval turn-on(see chart below).

3. When the lights relative to the wanted stand-by interval

turn-on, release the button.

4. Press to turn the appliance o (stand-by).

“Setting temperature” and “Adjust Stand-by” chart

Temperature Corresponding lights Stand-by after

Low

15 minutes

Medium

75 minutes

High 3 hours

Set the water hardness

The lights signaling the need to descale the appliance, after

a pre-set period of operation depends on the hardness of the

water.Itispossibletoprogramthemachineaccordingtothe

actual water hardness in use in the area, thus making descaling

less frequent. Proceed as follows:

1. Remove the provided reactive strip “TOTAL HARDNESS

TEST” from its packaging.

Activation of the water lter and lling of the water

tank

• Removethe lterfromthe packagingandrinseitwith

about17OZ/0.5Lofrunningwater(g.2).

• Turn the calendar disc (seeg.3) until the following 2

months of use are displayed.

Please note

thelterhas a twomonth duration if the applianceisused

normally, whereas if the machine remains unused with the

lterinstalled,ithasamaximum3monthduration.

• Removethewatertankandllitwithfreshwater(donot

exceedtheMAXline)(g.4).

• Completelydipthelterinthewater,tiltingittoenable

airbubblestocomeout(g.5).

• Insertthelterintheappropriateseat(g.6),pressdown

and close the tank with the lid.

• Placethetankbackintothemachine(Ensurethewater

levelisnotovertheMAXline)(g.7).

Thelterisnowactivatedandthemachinecanbeused.

Appliance rst use

• Turn the appliance on by pressing the I/O main switch

A3 at rear in pos. I: the appliance performs a self-test,

signalled by the sequential ashing of the lights.

•

Once the self-test is completed, the “hot water spout” light

B8asheswhiletheothersturn-o:theappliancesignals

itisnecessarytoinsertthehotwaterspout(g.8).

• Placea container underneaththespoutwithminimum

capacityof100ml(g.9).

• Pressthe“hotwater”button : delivery starts and

interrupts automatically.

• The coee and water spout lights ash to indicate the

appliance is reaching temperature: when the lights stop

ashing and remain permanently on, the appliance is

ready for use.

Please note: upon rst use

• Iflights and ash, press the button

again.

• Upon rst use, it is necessary to make 4-5 coees or

4-5 cappuccinos before the machine gives a satisfying

results.

Settings of the programming menu

To access the programming menu, ensure the appliance is

in stand-by, simultaneously press buttons

and

until the ON/Stand-by(B2) light ashes: the appliance is in

programmingmode.Setthemachineaswanted;toexitthe

Loading ...

Instructions for use - Page 10