Loading ...
Loading ...
Loading ...
14
Clean the exterior door panel
Colored doors: use only a soft cloth dampened with soapy water.
Stainless steel doors: use a soft cloth with a non-abrasive cleaner (preferably a
liquid spray) made for cleaning stainless steel. For the best results, apply the
stainless steel cleaner to the cloth and then wipe the surface.
Clean the door gasket
Regularly clean the door gasket with a damp cloth to remove food particles and
other debris. Also clean the door seal, located inside the dishwasher at the bot-
tom of the door.
Winterizing your unit
If your dishwasher will be unused for an extended period of time in a location that experiences freezing tempera-
tures (holiday home or through a vacation period), have your dishwasher winterized by an authorized profes-
sional service. Turn your household water supply to the dishwasher off when on extended vacation or when
dishwasher will not be used for more than 1 month.
Self Help
Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The
following information may help you with a dishwasher problem without involving a repair professional.
Problem Cause Action
Dishwasher does
not start
1. Door may not be properly latched
2. Unit may not be turned on
3. Unit not reset or previous cycle not completed
4. Delay start engaged
5. Interruption of electrical power supply to dish-
washer or blown fuse.
6. The door may have been closed without first
selecting a cycle
7. Water supply may not be turned on
1. Shut the door completely until you hear it click.
2. Press the main power switch to turn unit on.
3. To reset, refer to “Cancel a Cycle” (page 12) in this manual.
4. To reset, refer to “Delay Start” (page 12) section in this manual.
5. Check circuit breaker
6. Select a cycle and close the door.
7. Check and turn on water supply.
Dishwasher beep-
ing (end of cycle
signal)
1. Default factory settings alert the customer that
the cycle is complete by beeping. This feature can
be deactivated if so desired.
1. To adjust the volume or deactivate, refer to the “Cycle Com-
pletion Signal” (page 12) section in this manual.
Display does not
illuminate
1. A fuse may have been blown or circuit breaker
tripped
2. Door not closed or latched
Note: For models with controls on top of the door, the
display only illuminate when the door is opened and
controls are visible.
1. Check the fuse or circuit breaker box and replace the fuse or
reset the breaker if necessary
2. Ensure door is properly latched and completely closed
Dishwasher seems
to run a long time
1. Incoming water is not warm enough
2. Cycle time can vary due to soil and water condi-
tions
3. Rinse agent dispenser is empty
4. Dishwasher connected to cold water supply
Note: Refer to “Wash Cycle Information” (page 11)
section in this manual for typical cycle lengths
1. Before starting a cycle, run hot water faucet at the sink clos-
est to the dishwasher
2. Sensors in the dishwasher automatically increase the cycle
time to ensure a good wash when heavy soil is detected
3. Add rinse agent
4. Verify dishwasher is connected to hot water supply plumbing
Dishes are not get-
ting clean enough
1. Spray arm movement obstructed
2. Spray arm nozzles clogged
3. Improper use of detergents
4. Filters could be clogged
5. Dishes are nested or loaded too close together
6. Selected wash cycle is not suitable for food soil
conditions
1. Ensure that spray arm movement is not blocked by hand rotat-
ing spray arms before starting cycle
2. Remove the spray arms and clean according to the “Care and
Maintenance” (pages 13-14) section of the manual
3. Increase or decrease detergent depending on the water hard-
ness (refer to Table 1)
4. Clean the filters according to the “Care and Maintenance”
(pages 13-14) section of the manual
5. Rearrange load such that water spray can reach all items in
the dishwasher - see “Loading the Dishwasher” (page 5-7) sec-
tion of the manual
6. Refer to “Wash Cycle Information” (page 11) section of the
manual
Micro
Figure 14
Filter
Loading ...
Loading ...
Loading ...