Loading ...
Loading ...
Loading ...
49-7769
FINAL INSTALLATION
CHECKLIST
Ensure that all installation instructions
concerning clearances around the unit have
been adhered to.
,nspect and ensure that all components and
accessories have been installed properly and
that they have not been damaged during the
installation process.
Wall plenum flashing is installed, plenum level
and calked.
Unit is level, front to back and left to right.
Check to ensure that the unit air filter, indoor
coil, and outdoor coil are free from any
obstructions.
Check to make sure only one air filter is installed
in the system.
Check the condensate water drain(s) to ensure
that they are connected and adequate for the
removal of condensate water and that they meet
approval of the end user.
'XFWZRUNLVFRQQHFWHGDQGVHFXUHWRDLU
discharge outlet.
Secure all access panels (i.e. front cover and/or
FRQWUROER[
Wall thermostat is wired correctly.
Unit is wired correctly.
Ensure that the circuit breaker(s) /fuse(s) and
supply circuit wire size have been sized
correctly.
Ensure the unit has correct line voltage to it, is
on a single circuit and is properly grounded.
Ensure that the entire installation is in
compliance with all applicable national and local
codes and ordinances having jurisdiction.
CONNECT POWER
,IDOOWKHLWHPVRQWKHFKHFNOLVWDUHFRUUHFW
reinstall the power disconnect on the front of the
unit.
7XUQWKHSRZHURQDWWKHPDLQVHUYLFHSDQHO
7XUQRQDQGDGMXVWWKHWKHUPRVWDWVRWKHXQLW
begins to run.
&KHFNIRUSURSHURSHUDWLRQLQHDFKPRGH
,QVWUXFWWKHRZQHURURSHUDWRUUHJDUGLQJWKH
unit’s operation, and the recommended routine
maintenance schedule.
NOTE: Maintaining a log for recording the dates of
maintenance and/or service is recommended, and
should be suggested to the owner or operator of the
equipment.
SERVICING
WARNING
Risk of Electric Shock, can cause injury
or death.
Before servicing, switch power off at
the service panel and lock the area to prevent
power from being switched on accidentally. When
the area cannot be locked, securely fasten a
prominent warning device, such as a tag, to the
service panel.
NOTE: We strongly recommend that any servicing
be performed by a qualified individual.
To remove the unit from the closet.
6ZLWFKWKHZDOOWKHUPRVWDWWRRII
3XOOWKH3RZHU'LVFRQQHFWORFDWHGLQWKHIURQWRIWKH
chassis.
7XUQRIIDOOSRZHUFRPLQJLQWRWKHXQLWDWWKHPDLQ
breaker panel or the closet mounted disconnect.
'LVFRQQHFWWKHHOHFWULFDOFRQQHFWLRQDWWKHXQLW
'LVFRQQHFWWKHGUDLQV\VWHP
'LVFRQQHFWWKHGXFWZRUN
7. Slide the chassis out of the wall plenum.
8. Lift the chassis out of the utility closet.
Installation Instructions
INSTALLATION INSTRUCTIONS
ELECTRICAL CONNECTIONS (continued)
DIRECT CONNECTION
Heater Wattage
@ 230/208 Volts
Circuit Protective Device
.:
.:
.:
$PS7LPH'HOD\)XVHRU%UHDNHU
$PS7LPH'HOD\)XVHRU%UHDNHU
$PS7LPH'HOD\)XVHRU%UHDNHU
Heater Wattage
@ 265 Volts
Circuit Protective Device
.:
.:
.:
$PS7LPH'HOD\)XVHRU%UHDNHU
$PS7LPH'HOD\)XVHRU%UHDNHU
$PS7LPH'HOD\)XVHRU%UHDNHU
* See NEC for application for 265 Volts.
FINAL INSTALLATION
Loading ...
Loading ...
Loading ...