Loading ...
Loading ...
Loading ...
Description of other Functions, Method for Setting These Functions
Program Midway Change Function
Auto Dosing System (ADS)
Child Lock Function
Setting Method
Disabling Beeps
Residual Water Draining Function
This is a function that can change the parameters of a procedure that has not been
performed after a wash starts. Procedures that are being performed and has
already been performed cannot be changed. The Scheduled Procedure cannot be
changed. (this function is unavailable for One Key Smart Select, Spin Dry and
Tub Clean.)
Automatic Addition of Liquid Detergent: The L2 level is enabled by default. You can
also adjust the addition amount according to the water level or laundry soil level.
Automatic Addition of Softener: You can enable the Softener Function only when a
rinse will proceed. The Softener Indicator will be lit constantly after the function is
enabled.
Note: • If the Detergent or Softener Indicator is blinking, it is an alarm prompting you
that you need to add liquid detergent or softener. Pour an appropriate amount of
the liquid detergent or softener through the Liquid Detergent or Softener Addition
Mouth.
• After the proper addition ends, please wipe the surrounding of the Addition Mouth
Cap, put the stopper in place, and close the Addition Mouth Cap.
• The ADS can remember the last addition status.
You can enable the Child Lock Function to avoid injury to a child opening the
Drum Cover of the Washing Machine.
Press the Power Button to turn on the power. Press and hold the Super Soak
Button for more than 3 seconds until the Indicator is lit and you hear a
beep. Repeat the operation to enable it again.
• After the Child Lock is enabled, while a Program is running, no Buttons except the
Power Button will respond.
Cancel Method: Press the Power Button to turn on the power. Press and hold the
Start/Pause Button for more than 4 seconds until you hear a beep. Repeat the
operation to enable beeps.
Enable the Residual Water Draining Function. 9 minutes after the set Program
ends, the Display will show and the Drain Valve will be opened for 30
seconds to drain the residual water in the Machine. Afterward, if there is no
operation for 30 seconds, the power will be cut off automatically. (The Program will
perform this function by default)
• The Residual Water Draining Function is enabled by default. During Residual
Water Draining, no Buttons except the Power Button will respond. After the
Residual Water Draining ends, the power will be cut off automatically without beeps.
• Method to Disable the Residual Water Draining Function: Press the Power Button
to turn on the power. Press and hold the Spin Time Button for more than 4
seconds and the function will be disabled. Repeat the operation to enable the
function.
Note: The Residual Water Draining Function will not work in Programs without
draining and spin-drying.
Troubleshooting Guide
When any of the following problems occurs, the Smart Microcontroller will detect
the abnormal status and emit alarming beeps for about 10 seconds, and the Digital
Display will display the following in the Table below.
Notes:
After all the items are checked and addressed, press the Start/Pause Button. If no
fault is displayed, the Washing Machine will resume its running. If there is still any
abnormality, please unplug the Power Cord and call the company’s Customer
Service number as soon as possible.
Fault Type
Fault Displayed
Cause
The washer
does not
work at all
Water does
not flow into
the drum
Water does
not drain out
Washer does
not spin
Wash Failure
Others
etc.
• Is the power connected?
• Has the Start/Pause Button been pressed?
• Is it in a Schedule State?
• Is the power fuse or current circuit breaker
intact ?
• Is there a power failure?
• Is the Faucet turned on?
• Is the Water Inlet Hose or the Screen Lint Filter
of the Water Inlet Valve blocked?
• Has the Water Inlet Hose of the Washing
Machine Water Hose been frozen?
• Is the water pressure too small and the water
addition time too long?
• Is the Drain Hose laid down?
• Is the Drain Mouth in a too high position (of
more than 15cm)?
• Is the Drain Mouth blocked?
• Is the laundry mostly on one side of the
Washing/Spin-drying Drum?
• Is the Washing Machine placed flatly?
Is the washer lid open?
• Is the Child Lock Function enabled?
• Is the washer lid open?
• Please press the Power Button to turn off
the power, unplug the Power Cord Plug,
and call the company’s Customer Service
number as soon as possible.
Non-malfunction Cases
1. Sometimes water is added during a wash or rinse. This is automatic water
replenishment due to a lowered water level.
2. At the beginning of Spin-drying, the drum will stop and start intermittently. This
is intermittent Spin-drying designed to achieve a better Spin-drying effect.
3. During the Spill Rinse, the Drain Hose does not drain water. This is due to the
set water level being too low or the water pressure being too low.
4. Sometimes water is replenished during Spin-drying. This is an automatic
replenishment due to the improper placement of the laundry to be Spin-dried.
5. After the Spin-drying ends, there is the sound of residual water, which is the
sound of the balance liquid that is in the balance ring and designed to reduce
Spin-drying vibration.
6. There was a power failure during operation and the operation cannot be
automatically resumed after the power supply restores. Please set the Machine
again.