Loading ...
Loading ...
Loading ...
4
OPERATION
BLOWER ACTIVATION/SPEED LEVEL CHANGE/
FILTER INDICATOR RESET
When blowers are OFF, press on this push button to turn ON
the blowers at the last saved speed. If there was no speed
saved, the blowers will be set on LOW speed.
NOTE: When LOW speed is activated from OFF, the
blowers start on MEDIUM speed for a very short
lapse of time, and then resume to LOW speed.
To change the blower speed, press on this push button again
until the desired speed is reached (from LOW to MEDIUM to
HIGH speed to OFF). Each time a blower speed is activated,
a rotating blower icon appears on left side of LCD screen,
with dot(s) under it (the rotation speed shows the chosen
speed: slow for LOW with one dot, faster for MEDIUM with
2 dots and fastest for HIGH with 3 dots).
When blowers are on (no matter the speed level), press and
hold this push button until the blower icon disappears from
the LCD screen; this will turn off the blowers and save the
blower speed chosen.
Heat Sentry™
This hood is equipped with a protective device that activates
the blowers when an abnormally high heat level is detected
while the blowers are activated. During the Heat Sentry
activation, this device takes control of the blowers and set
them on MEDIUM speed while all dots under the blower
icon blink. However, the lights can be still controlled. The
blowers will remain on MEDIUM speed until the heat is back
to normal, they then return to the speed previously selected.
NOTE: When excessive heat is detected, Heat Sentry will
shut off both blowers and lights while all dots under
the blower icon will blink faster. Both blowers and
lights will remain off until the ambient temperature
cools down; the blowers will then start on MEDIUM
speed (the lights can be controlled again). The
blowers will remain on MEDIUM speed until the heat
is back to normal, they then return to the speed
previously selected.
1
NOTE: At range hood start-up or after a power failure,
a small icon (1) appears shortly (for ± 2 seconds) on
LCD screen; this is normal.
DELAY OFF
When the blowers are on, press this button to activate the
delay function. This icon appears on LCD screen beside the
blower icon to indicate the function is on. The blowers will
continue to operate for 10 minutes and then, will shut off
automatically (both blower and delay icons will disappear
from LCD screen). When Delay off is activated, it is possible
to change the blower speed by pressing on blower push
button without aff ecting the remaining time of the delay.
To cancel the delay off function before the end of the
10-minute cycle, press again on delay off push button.
ON LIGHTING/LIGHT INTENSITY CHANGE
Press this push button to turn on the lights at the last saved
intensity; the light icon appears on right side of LCD screen
and the number of dots below it shows which light intensity
is on (one dot for LOW, two dots for MEDIUM and three
dots for HIGH).
To change the light intensity, press the push button until the
desired level is reached (from HIGH intensity, pressing again
will shut off the lights).
When lights are on (no matter the light intensity), press and
hold this push button until the light icon disappears from the
LCD screen; this will shut off the lights and save the chosen
light intensity.
The LED modules included with this hood are the latest in
LED cooktop illumination technology specially designed
to operate in the elevated temperatures of cooking -
off ering bright lighting and lasting up to 25 times as long
as a standard bulb and greater reliability than typical
replacement LED bulbs.
MASTER ON/OFF
Press this push button to turn on the ligths and the blowers
at the last saved intensity. When either lights or blowers are
ON, pressing on this push button will memorize the current
blower speed and lighting level prior to shut them OFF.
FILTER CLEANING REMINDER
This icon appears on LCD screen 30 seconds after turning
OFF the blowers when it is time to clean hood and fi lters
(refer to Cleaning and Maintenance on page 5). This
happens every time the blowers are turned OFF until the
fi lter cleaning reminder has been reset. Once the cleaning
is done, reset the fi lter cleaning reminder by pressing on
blower activation push button for 3 seconds while the icon
appears on LCD screen for 30 seconds.
OPERATION
Loading ...
Loading ...
Loading ...