Loading ...
Loading ...
Loading ...
3. Electrical Requirements
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse. To know the
circuit breaker or fuse required by your model, see
the serial plate to find the wattage consumption
and refer to table A to get the circuit breaker or
fuse amperage.
| I
Appliance ProtectiQn Appliance ProtectiQn
Rating Watts Circuit Rating Watts Circuit
n H
240V Recommended 208V Recommended
Lessthan 4800W 20A Lessthan 4100W 20A
4800W - 7200W 30A 4100W - 6200W 30A
7200W - 9600W 40A 6200W - 8300W 40A
9600W and + 50A 8300W and + 50A
Table A
Observe all governing codes and local ordinances
1. A 3-wire or 4-wire single phase 120/240 or
120/208 Volt, 60 Hz AC only electrical supply is
required on a separate circuit fused on both sides
of the line (red and black wires). A time-delay fuse
or circuit breaker is recommended. DO NOT fuse
neutral (white wire). Onty certain cooktop models
may be installed over certain built-in electric oven
models. Approved cooktops and built-in ovens are
listed by the MFG ID number (see the insert sheet
included in the literature package).
NOTE: Wire sizes and connections must conform
with the fuse size and rating of the appliance in
accordance with the American National Electrical
Code ANSI/NFPA No. 70-latest edition, or with
Canadian CSA Standard C22.1, Canadian Electrical
Code, Part 1, and local codes and ordinances.
An extension cord should not be used
with this appllance. Such use may result in a fire,
electrlcal shock, or other personal injury, if you
need a longer power cord you can purchase a 10'
(3 m) power cord kit #903056-9010 by calling the
Service Center.
2. These appliances should be connected to the
fused disconnect (or circuit breaker) box through
flexible armored or nonmetallic sheathed cable.
The flexible armored cable extending from the
appliance shoutd be connected directly to the
junction box. The junction box should be located
as shown in Figure 1 or Figure 2 and with as
much slack as possible remaining in the cable
between the box and the appliance, so it can be
moved if servicing is ever necessary.
3. A suitable strain relief must be provided to
attach the flexible armored cable to the
junction box.
Electrical Shock Hazard
* Electrlcal ground is required on this
appliance.
* Do not connect to the electrlcal supply until
appffance is permanenHv grounded.
* Disconnect power to the junction box before
making the electrlcal connection.
* This appliance must be connected to a
grounded, metallic, permanent wiring system,
or a grounding connector should be connected
to the grounding terminal or wire lead on the
appffance.
* Do not use a gas supply llne for grounding the
appffance.
Failure to do any of the above could result in a
fire, personal injury or electrical shock.
4. Electrical connection
It is the responsibility and obligation of the
consumer to contact a qualified installer to assure
that the electrical installation is adequate and is
in conformance with the National Electrical Code
ANSI/NFPA No. 70-latest edition, or with CSA
Standard C22.1, Canadian Electrical Code, Part 1,
and local codes and ordinances.
Risk of electrical shock (Failure to
heed this warning may result in electrocution or
other serious injury.) This appllance is equipped
with copper lead wire. if connection is made to
aluminum house wiring, use only connectors that
are approved for joining copper and aluminum
wire in accordance with the National Electrical
Code and local code and ordinances. When
installing connectors having screws which bear
direcHy on the steel and/or alumlnum fiexlble
conduit, do no tighten screws sufflcientiy to
damage the flexible conduit. Do not over bend
or excessively distort fiexlble conduit to avoid
separation of convolutions en exposure of internal
wires.
DO NOT ground to a gas supply pipe. DO NOT
connect to electrical power supply until appliance
is permanently grounded. Connect the ground wire
before turning on the power.
4
Loading ...
Loading ...
Loading ...