Loading ...
Loading ...
Loading ...
23
Chopper Accessory (D)
The chopper (10) is perfectly suited for chopping
meat, hard cheese, onions, herbs, garlic,
vegetables, bread, crackers and nuts.
Use the «mc» chopper (10) for larger quantities and
for hard foods.
For «mc» chopper do not exceed the quantity of
ingredients higher than max line.
For «hc» chopper do not exceed the quantity of
ingredients higher than max line. Maximum
operation time for the «hc» chopper: 1 minute for
large amounts of wet ingredients, 30 seconds for
dry or hard ingredients.
NOTE: leave an interval of at least 3 minutes before
operating again (To prevent faults). Immediately
stop processing when motor speed decreases and/
or strong vibrations occur.
Refer to the Processing Guide D for maximum
quantities, recommended times and speeds.
Before Use
• Pre-cut foods into small pieces for easier
chopping.
• Remove any bones, tendons and gristle from
meat to help prevent damage to the blades.
• Make sure the anti-slip rubber ring (10e) is
attached to the bottom of the chopper bowl.
Assembly and Operation
• Carefully remove the plastic cover from the
blade.
• The blades (10b/10c) are very sharp! Always
hold it by the upper plastic part and handle it
carefully.
• Place the blade on the center pin of the chopper
bowl (10d). Press it down and give it a turn so
that it locks into place.
• Fill the chopper with food and put on the lid (10a).
• For ice crushing, use the special ice blade (10c).
• To achieve good results fill up to 5 ice cubes in
«mc» chopper and chop 10-15 seconds.
• Align the chopper with the motor part (4) and
click together.
• To operate the chopper, switch on the appliance.
During processing, hold the motor part with one
hand and the chopper bowl with the other.
• Always chop harder foods (e.g. parmesan
cheese) at full speed.
• When chopping is complete, unplug and press
the EasyClick Plus release buttons (5) to detach
the motor part.
• Lift the lid up. Carefully take out the blade before
pouring out the contents of the bowl. To remove
the blade, slightly turn it then pull it off.
Caution
• Do not use the chopper accessory to process
extremely hard foods, such as unshelled nuts,
ice cubes, coffee beans, grains, or hard spices
e.g. nutmeg. Processing these foods could
damage the blades.
• Only the «mc» chopper accessory (10) with the
special ice blade (10c) is allowed to crush ice
cubes.
• If using the appliance to puree hot food ensure
the liquid is not boiling. Allow hot food to cool
slightly to avoid risk of scalding.
• Never place the chopper bowls in the microwave
oven.
«hc» Recipe example: Honey-Prunes (as a pancake
stuffing or spread)
50 g prunes
75 g creamy honey
70 ml water (vanilla-flavour)
• Fill the «hc» chopper bowl with prunes and
creamy honey.
• Store at 3 °C in refrigerator for 24 hours.
• Add 70 ml water (vanilla-flavoured).
• Chop 1,5 seconds at maximum speed (fully press
the Smartspeed switch).
Use the chopper accessory «hc» (optional
accessory available at your Braun Service Center;
however not in every country).
Food Processor Accessory XL
with Dicer
The food processor accessory with Dicer (11) can
be used for:
• Chopping, blending and mixing Pancake batter;
• kneading dough and preparing cake batter,
based on max. 500 g flour (cake batter is only
possible with models containing the dough tool
(11k);
• slicing, shredding, julienning and making French
fries;
• dicing.
Chopping (E)
Using the blade (11i) you can chop meat, hard
cheese, onions, herbs, garlic, vegetables, bread,
crackers, and nuts.
Refer to the Processing Guide E for maximum
quantities, recommended times and speeds.
Before Use
• Pre-cut foods into small pieces for easier
chopping
• Remove any bones, cartilage, tendons and
gristle from meat to help prevent damage to the
blades.
• Remove stems from herbs, shell nuts.
• Make sure the anti-slip rubber ring (11h) is
attached to the bottom of the food processor
bowl.
Assembly and Operation
• Carefully remove the chopper blade cover (11j)
from the blade.
5722114234_01_HB901-MQ91-75-87-95 INT.indd 23 08.02.21 14:50
Loading ...
Loading ...
Loading ...